Rapid Prototyping Journal最新文献

{"title":"Multimaterial 3D printing of auxetic jounce bumpers for automotive suspensions","authors":"Alberto Giubilini, Paolo Minetola","doi":"10.1108/rpj-02-2023-0066","DOIUrl":"https://doi.org/10.1108/rpj-02-2023-0066","url":null,"abstract":"Purpose The purpose of this study is to evaluate the 3D printability of a multimaterial, fully self-supporting auxetic structure. This will contribute to expanding the application of additive manufacturing (AM) to new products, such as automotive suspensions. Design/methodology/approach An experimental approach for sample fabrication on a multiextruder 3D printer and characterization by compression testing was conducted along with numerical simulations, which were used to support the design of different auxetic configurations for the jounce bumper. Findings The effect of stacking different auxetic cell modules was discussed, and the findings demonstrated that a one-piece printed structure has a better performance than one composed of multiple single modules stacked on top of each other. Research limitations/implications The quality of the 3D printing process affected the performance of the final components and reproducibility of the results. Therefore, researchers are encouraged to further study component fabrication optimization to achieve a more reliable process. Practical implications This research work can help improve the manufacturing and functionality of a critical element of automotive suspension systems, such as the jounce bumper, which can efficiently reduce noise, vibration and harshness by absorbing impact energy. Originality/value In previous research, auxetic structures for the application of jounce bumpers have already been suggested. However, to the best of the authors’ knowledge, in this work, an AM approach was used for the first time to fabricate multimaterial auxetic structures, not only by co-printing a flexible thermoplastic polymer with a stiffer one but also by continuously extruding multilevel structures of auxetic cell modules.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-31","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135927880","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Investigation and optimization of hot pressed porcelain dental prostheses production by MSLA application","authors":"Ana Carla Cordeiro, Gustavo George Verdieri Nuernberg, Lilian Cristina Côcco, Marlon Wesley Machado Cunico","doi":"10.1108/rpj-05-2023-0180","DOIUrl":"https://doi.org/10.1108/rpj-05-2023-0180","url":null,"abstract":"Purpose Different technologies may currently be used to produce dental prostheses, such as additive manufacturing and traditional milling. This study aims to evaluate and improve the fabrication process for hot-pressed porcelain dental prostheses and compare the use of masked stereolithography apparatus (MSLA) casting to computer-aided design/computer-aided manufacturing (CAD/CAM) casting. The cost-benefit analysis of producing dental prostheses through various technologies, including additive manufacturing and traditional milling, has not been fully explored. The cost of materials and processes used to produce prostheses varies based on complexity of design and materials used, and long-term effects, such as durability and wear and tear, must be taken into account. Design/methodology/approach Using key elements of part costs and estimation cost models, a multivariable approach was used to evaluate the practicality of the recommended strategy and process improvement. Findings The research found that MSLA casting provides a higher return on investment than CAD/CAM casting, and the optimized production process could be more suitable for the size and annual demand for prostheses. Originality/value Overall, this study highlights the need for a more comprehensive understanding of the cost-benefit analysis of different dental prosthesis production methods and emphasises the importance of evaluating long-term effects on the cost-benefit analysis.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136018904","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Method for manufacturing ergonomic bespoke external breast prostheses using low-cost computer-aided technology","authors":"Lucia Regina, José Aguiomar Foggiatto","doi":"10.1108/rpj-06-2023-0200","DOIUrl":"https://doi.org/10.1108/rpj-06-2023-0200","url":null,"abstract":"Purpose Breast cancer is the most diagnosed type of cancer in the world, and mastectomies to remove tumors are still common. An external breast prosthesis (EBP) can be used to minimize the asymmetry, due to the ablation. Some governments do not cover costs of that assistive technology, and women end up using socks and fabric pockets filled with seeds, to simulate the volume lost in the surgery. This study aims to offer to those women a decent solution, ergonomic, but still affordable. Design/methodology/approach The authors interviewed 20 mastectomized Brazilian women, listened to their relate and 3D scanned them, to give rise to personalized external lightweight breast prostheses. The authors used free software for computer-aided design and computer-aided manufacturing, and low-cost 3D printers. From the strategy of bespoke products, this study generalized the method, to conceive mass customized prostheses, in a compromise solution that reduces personalization, conserving the best features of design. Findings This study achieved a method to manufacture ergonomic, bespoke external breast prostheses, using low-cost technology. Previous literature made them using expensive scanners, software and printers. Research limitations/implications The authors validated this method during pandemic, which restricted the number of patients the authors could have access to. This impacted authors’ possibility to work on matching the color of the final product and real skin. The authors understood, though, that precision of color, in the final product, is challenging, because of the peculiar aspects of human skin. Originality/value Using the method the authors proposed, personalized external breast prostheses can be manufactured using low-cost resources, democratizing better quality of life for more breast cancer survivors.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135217877","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Development of process-structure linkage for Inconel 718 processed by laser powder bed fusion: a numerical modeling approach","authors":"Anuj Kumar, Mukul Shukla","doi":"10.1108/rpj-02-2023-0064","DOIUrl":"https://doi.org/10.1108/rpj-02-2023-0064","url":null,"abstract":"Purpose Understanding and tailoring the solidification characteristics and microstructure evolution in as-built parts fabricated by laser powder bed fusion (LPBF) is crucial as they influence the final properties. Experimental approaches to address this issue are time and capital-intensive. This study aims to develop an efficient numerical modeling approach to develop the process–structure (P-S) linkage for LPBF-processed Inconel 718. Design/methodology/approach In this study, a numerical approach based on the finite element method and cellular automata was used to model the multilayer, multitrack LPBF build for predicting the solidification characteristics (thermal gradient G and solidification rate R) and the average grain size. Validations from published experimental studies were also carried out to ensure the reliability of the proposed numerical approach. Furthermore, microstructure simulations were used to develop P-S linkage by evaluating the effects of key LPBF process parameters on G × R, G/R and average grain size. A solidification or G-R map was also developed to comprehend the P-S linkage. Findings It was concluded from the developed G-R map that low laser power and high scan speed will result in a finer microstructure due to an increase in G × R, but due to a decrease in G/R, columnar characteristics are also reduced. Moreover, increasing the layer thickness and decreasing the hatch spacing lowers the G × R, raises the G/R and generates a coarse columnar microstructure. Originality/value The proposed numerical modeling approach was used to parametrically investigate the effect of LPBF parameters on the resulting microstructure. A G-R map was also developed that enables the tailoring of the as-built LPBF microstructure through solidification characteristics by tuning the process parameters.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-19","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135666878","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Evaluation of a method for the additive tooling of injection mould inserts","authors":"Steffen Schrock, Stefan Junk, Albert Albers","doi":"10.1108/rpj-04-2023-0139","DOIUrl":"https://doi.org/10.1108/rpj-04-2023-0139","url":null,"abstract":"Purpose This study aims to investigate a systematic approach to the production and use of additively manufactured injection mould inserts in product development (PD) processes. For this purpose, an evaluation of the additive tooling design method (ATDM) is performed. Design/methodology/approach The evaluation of the ATDM is conducted within student workshops, where students develop products and validate them using AT-prototypes. The evaluation process includes the analysis of work results as well as the use of questionnaires and participant observation. Findings This study shows that the ATDM can be successfully used to assist in producing and using AT mould inserts to produce valid AT prototypes. As a reference for the implementation of AT in industrial PD, extracts from the work of the student project groups and suitable process parameters for prototype production are presented. Originality/value This paper presents the application and evaluation of a method to support AT in PD that has not yet been scientifically evaluated.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-19","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135666720","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Simulation of temperature profile in fused filament fabrication 3D printing method","authors":"Nastaran Mosleh, Masoud Esfandeh, Soheil Dariushi","doi":"10.1108/rpj-02-2023-0067","DOIUrl":"https://doi.org/10.1108/rpj-02-2023-0067","url":null,"abstract":"Purpose Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied. Design/methodology/approach COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand. Findings The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand. Originality/value The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136293219","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Assessment of the mechanical properties of PC/ABS blends for functional prototyping by FFF 3D printing","authors":"Cleiton Lazaro Fazolo De Assis, Cleber Augusto Rampazo","doi":"10.1108/rpj-04-2023-0153","DOIUrl":"https://doi.org/10.1108/rpj-04-2023-0153","url":null,"abstract":"Purpose This paper aims to evaluate the mechanical behaviour of polycarbonate/acrylonitrile butadiene styrene (PC/ABS) filaments for fusion filament fabrication (FFF). PC/ABS have emerged as a promising material for FFF due to their excellent mechanical properties. However, the optimal processing conditions and the effect of the blending ratio on the mechanical properties of the resulting workpieces are still unclear. Design/methodology/approach A statistical factorial matrix was designed, including infill pattern, printing speed, nozzle size, layer height and printing temperature as factors (with three levels). A total of 810 workpieces were printed using PC/ABS blends filament with the FFF. The workpieces’ finishing and mass were evaluated. Tensile tests were performed. Analysis of variance was performed to determine the main effects of the processing conditions on the mechanical properties. Findings The results showed that the PC/ABS (70/30) exhibited higher tensile. Tensile rupture corresponded to 30% of the tensile strength. The infill pattern showed the highest contribution to the responses. The concentric pattern showed higher tensile strength. Tensile strength and mass ratio demonstrated the influence of mass on tensile strength. The influence of printing parameters on deformation depended on the blend proportions. Higher printing speed and lower layer height provided better quality workpieces. Originality/value This study has implications for the design and manufacturing of three-dimensional printed parts using PC/ABS filaments. An extensive experimental matrix was applied, aiming at a complete understanding of mechanical behavior, considering the main printing parameters and combinations not explored by literature.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-06","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135304281","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Experimental characterization, theoretical modeling and failure analysis of the mechanical behavior of acrylonitrile butadiene styrene parts by fused filament fabrication","authors":"Roberto Junior Algarín Roncallo, Luis Lisandro Lopez Taborda, Diego Guillen","doi":"10.1108/rpj-03-2023-0097","DOIUrl":"https://doi.org/10.1108/rpj-03-2023-0097","url":null,"abstract":"Purpose The purpose of this research is present an experimental and numerical study of the mechanical properties of the acrylonitrile butadiene styrene (ABS) in the additive manufacturing (AM) by fused filament fabrication (FFF). The characterization and mechanical models obtained are used to predict the elastic behavior of a prosthetic foot and the failure of a prosthetic knee manufactured with FFF. Design/methodology/approach Tension tests were carried out and the elastic modulus, yield stress and tensile strength were evaluated for different material directions. The material elastic constants were determined and the influence of infill density in the mechanical strength was evaluated. Yield surfaces and failure criteria were generated from the tests. Failures over prosthetic elements in tridimensional stresses were analyzed; the cases were evaluated via finite element method. Findings The experimental results show that the material is transversely isotropic. The elasticity modulus, yield stress and ultimate tensile strength vary linearly with the infill density. The stresses and the failure criteria were computed and compared with the experimental tests with good agreement. Practical implications This research can be applied to predict failures and improve reliability in FFF or fused deposition modeling (FDM) products for applications in high-performance industries such as aerospace, automotive and medical. Social implications This research aims to promote its widespread adoption in the industrial and medical sectors by increasing reliability in products manufactured with AM based on the failure criterion. Originality/value Most of the models studied apply to plane stress situations and standardized specimens of printed material. However, the models applied in this study can be used for functional parts and three-dimensional stress, with accuracy in the range of that obtained by other researchers. The researchers also proposed a method for the mechanical study of fragile materials fabricated by processes of FFF and FDM.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135696293","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Selection methodology for additive manufacturing processes considering design, material, and manufacturability","authors":"Suraj Goala, Prabir Sarkar","doi":"10.1108/rpj-05-2023-0155","DOIUrl":"https://doi.org/10.1108/rpj-05-2023-0155","url":null,"abstract":"Purpose One of the critical reasons for the nonacceptance of additive manufacturing (AM) processes is the lack of understanding and structured knowledge of design for additive manufacturing (DfAM). This paper aims to assist designers to select the appropriate AM technology for product development or redesign. Using the suggestion provided by the design assist tool, the user’s design alterations depend on their ability to interpret the suggestion into the design without affecting the design’s primary objective. Design/methodology/approach This research reports the development of a tool that evaluates the efficacy values for all seven major standard AM processes by considering design parameters, benchmark standards within the processes and their material efficacies. In this research, the tool provides analytical and visual approaches to suggestion and assistance. Seventeen design parameters and seven benchmarking standards are used to evaluate the proposed product and design quality value. The full factorial design approach has been used to evaluate the DfAM aspects, design quality and design complexity. Findings The outcome is evaluated by the product and design quality value, material suit and material-product-design (MPD) value proposed in this work for a comparative assessment of the AM processes for a design. The higher the MPD value, the better the process. The visual aspect of the evaluation uses spider diagrams, which are evaluated analytically to confirm the results’ appropriateness with the proposed methodology. Originality/value The data used in the database is assumed to make the study comprehensive. The output aims to help opt for the best process out of the seven AM techniques for better and optimized manufacturing. This, as per the authors’ knowledge, is not available yet.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-09-29","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135132658","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Controlling anisotropy and brittle-to-ductile transitions by varying extrusion width in short fibre reinforced additive manufacturing","authors":"Jiongyi Yan, Emrah Demirci, Andrew Gleadall","doi":"10.1108/rpj-09-2022-0315","DOIUrl":"https://doi.org/10.1108/rpj-09-2022-0315","url":null,"abstract":"Purpose Extrusion width, the width of printed filaments, affects multiple critical aspects in mechanical properties in material extrusion additive manufacturing: filament geometry, interlayer load-bearing bonded area and fibre orientation for fibre-reinforced composites. However, this study aims to understand the effects of extrusion width on 3D printed composites, which has never been studied systematically. Design/methodology/approach Four polymers with and without short-fibre reinforcement were 3D printed into single-filament-wide specimens. Tensile properties, mechanical anisotropy and fracture mechanisms were evaluated along the direction of extruded filaments (F) and normal to the interlayer bond (Z). Extrusion width, nozzle temperature and layer height were studied separately via single-variable control. The extrusion width was controlled by adjusting polymer flow in the manufacturing procedure (gcode), where optimisation can be achieved with software/structure design as opposed to hardware. Findings Increasing extrusion width caused a transition from brittle to ductile fracture, and greatly reduced directional anisotropy for strength and ductility. For all short fibre composites, increasing width led to an increase in strain-at-break and decreased strength and stiffness in the F direction. In the Z direction, increasing width led to increased strength and strain-at-break, and stiffness decreased for less ductile materials but increased for more ductile materials. Originality/value The transformable fracture reveals the important role of extrusion width in processing-structure-property correlation. This study reveals a new direction for future research and industrial practice in controlling anisotropy in additive manufacturing. Increasing extrusion width may be the simplest way to reduce anisotropy while improving printing time and quality in additive manufacturing.","PeriodicalId":20981,"journal":{"name":"Rapid Prototyping Journal","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-09-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135477612","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}