2011 Fourth International Conference on Emerging Trends in Engineering & Technology最新文献

Effect of UWB Interference on WiMAX System 超宽带干扰对WiMAX系统的影响

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-12-01 DOI: 10.1109/TISC.2011.6169091

R. Thakare, K. Kulat

引用次数: 0

Design and Implementation of High Speed, Low Area Multiported Loadless 4T Memory Cell 高速、低面积、多端口无负载4T存储单元的设计与实现

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.23

D. Yagain, Ankit Parakh, Akriti Kedia, Gunjan Kumar Gupta

{"title":"Design and Implementation of High Speed, Low Area Multiported Loadless 4T Memory Cell","authors":"D. Yagain, Ankit Parakh, Akriti Kedia, Gunjan Kumar Gupta","doi":"10.1109/ICETET.2011.23","DOIUrl":"https://doi.org/10.1109/ICETET.2011.23","url":null,"abstract":"In several applications, the embedded SRAMs can occupy the majority of the chip area and contain hundreds of millions of transistors. Since RAMs are critical to processor performance, researchers have sought to optimize their performance and efficiency through reconfiguration [1]. This paper presents the architecture and circuit design for a multiported SRAM building block. In this paper SRAM cell with load (6T) and without load (4T) is designed and implemented in 180nm technology and comparison between them was made in terms of power consumed, area used and access time. It was found that load less 4T SRAM cell consumes less power as compared to 6T SRAM cell and occupies lesser area. Here as an application example, 8X1 memory using load less 4T is implemented. The decoding here is again done with Traditional CMOS decoder and Lyon Schediwy decoder. It is observed that the later performs much better in terms of power, timing and is area efficient. The 6T and 4T load less memory cell is further converted for multiport operation and simulated for various performance parameters such as area, power and delay and compared.","PeriodicalId":443239,"journal":{"name":"2011 Fourth International Conference on Emerging Trends in Engineering & Technology","volume":"18 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2011-11-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123734244","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 11

System of Systems and Emergence Part 2: Synergetic Effects and Emergence 系统的系统和涌现。第二部分:协同效应和涌现

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.52

N. Karcanias, A. Hessami

引用次数: 10

Challenges in Flexible Workflow Architecture: A Review 灵活工作流架构中的挑战:综述

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.64

S. M. Tayade, Vinay Chavan

引用次数: 4

Analysis of Adaptive LMS Filtering in Contrast to Multirate Filtering 自适应LMS滤波与多速率滤波的对比分析

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.48

Amanpreet Singh, B. Bansal

引用次数: 3

Design and Implementation of the Low Power 0.64mW, 380 KHz Continuous Time Sigma Delta ADC 低功率0.64mW, 380 KHz连续时间σ δ ADC的设计与实现

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.68

Aniruddha Kanhe, B. Acharya, R. Deshmukh

引用次数: 5

Design and Analysis of Glass Fiber Reinforced Polymer (GFRP) Leaf Spring 玻璃纤维增强聚合物(GFRP)钢板弹簧设计与分析

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.61

B. B. Deshmukh, S. Jaju

{"title":"Design and Analysis of Glass Fiber Reinforced Polymer (GFRP) Leaf Spring","authors":"B. B. Deshmukh, S. Jaju","doi":"10.1109/ICETET.2011.61","DOIUrl":"https://doi.org/10.1109/ICETET.2011.61","url":null,"abstract":"Weight reduction is now the main issue in automobile industries. Weight reduction can be achieved primarily by the introduction of better material, design optimization and better manufacturing processes. The achievement of weight reduction with adequate improvement of mechanical properties has made composite a very good replacement material for conventional steel. Selection of material is based on cost and strength of material. The composite materials have more elastic strain energy storage capacity and high strength to weight ratio as compared with those of steel, so multi-leaf steel springs are being replaced by mono-leaf composite springs. The paper gives the brief look on the suitability of composite leaf spring on vehicles and their advantages. The objective of the present work is design, analysis and fabrication of mono composite leaf spring. The design constraints are stress and deflections. The material selected is glass fibre reinforced plastic (GFRP) and the epoxy resin can be used which is more economical to reduce total cost of composite leaf spring with similar mechanical and geometrical properties to the multileaf spring. The composite leaf spring is fabricated by hand lay-up technique and tested. The testing was performed experimentally with the help of UTM and by (FEA) using ANSYS software showing stresses and deflections were verified with analytical and experimental results. Compared to the steel spring, the composite spring has stresses that are much lower, the spring weight is nearly 74% lower.","PeriodicalId":443239,"journal":{"name":"2011 Fourth International Conference on Emerging Trends in Engineering & Technology","volume":"28 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2011-11-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124845964","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 21

Microwave Interstitial Thermal Ablation of Hepatic Tumors by Extended Tip Sliding Choke Antenna 微波间质热消融在肝肿瘤中的应用

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.41

S. Maini, A. Marwaha

引用次数: 5

Parallel Concatenation of LDPC Codes with Two Sets of Source Bits 具有两组源位的LDPC码的并行连接

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.46

P. C. Catherine, K. Soyjaudah

引用次数: 5

Mobile Robot Programming by Demonstration 移动机器人编程演示

2011 Fourth International Conference on Emerging Trends in Engineering & Technology Pub Date : 2011-11-18 DOI: 10.1109/ICETET.2011.30

A. Kumaar, T. Sudarshan

引用次数: 16