{"title":"Innovative Cycles for Industrial Combined Heat and Power Generation With Carbon Capture and Storage","authors":"Riddhi R. Kapoor, S. Klein","doi":"10.1115/gt2022-80697","DOIUrl":"https://doi.org/10.1115/gt2022-80697","url":null,"abstract":"\u0000 Industry is a major contributor to the rise in global CO2 emissions, constituting one fifth of the global energy consumption, of which a significant amount is provided by fossil fuel combustion. Following the Paris agreement, emphasis has been made on the decarbonization of the industrial sector. This study focuses on industrial decarbonization by employing Carbon Capture and Storage for Combined Heat and Power (CHP) gas turbine plants. The scope of this study includes conceptual modelling and thermodynamic analysis of potential decarbonization options for zero carbon CHP plants. The studied options include post-combustion capture, exhaust gas recirculation, pre-combustion capture and oxyfuel combustion. As conventional air Brayton cycles are not applicable for oxy-fuel combustion in gas turbines, different working fluids and cycle configurations are proposed and thermodynamic performance is evaluated. Selected cycles were then compared based on thermodynamics, economics and off-design performance at a typical constant power to heat ratio of 0.78. It was observed that oxyfuel CHP cycle with CO2 working fluid is a promising solution for zero carbon CHP with relatively low costs and 100% CO2 capture. However, this solution requires new turbomachinery design.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116886466","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Majed Sammak, Maruthi Jupudi, A. Dawood, A. Khalidi
{"title":"Waste Heat Recovery Driven Turbocharger System for Gas Turbine","authors":"Majed Sammak, Maruthi Jupudi, A. Dawood, A. Khalidi","doi":"10.1115/gt2022-82941","DOIUrl":"https://doi.org/10.1115/gt2022-82941","url":null,"abstract":"\u0000 This paper introduces a novel concept for power augmentation by waste heat recovery turbocharger system. The turbocharger system, coupled to an external air compressor, is driven by the exhaust gases waste heat. The air compressor then compresses additional air that will be injected into the gas turbine compressor discharge and boost the gas turbine power. As the heat recovery system drives the turbocharger with heat recovered from the exhaust gas stream, the power produced by the power generation system increases without decreasing the efficiency.\u0000 Compressed air injection helps with resorting the missing gas turbine compressor air at high ambient temperatures and thus the compressed air injection is more suitable for gas turbines operating at hot ambient conditions. The paper also investigates utilizing the waste heat recovery turbocharger system at gas turbine part load operation for fuel saving and heat rate improvements.\u0000 This paper analyzes the gas turbine simple cycle power improvements at different ambient conditions and compressed air injection percentage. The gas turbine power proved to increase by around 2% at 1% air injection and 10% at 5% air injection at high ambient temperatures 30°C, 40°C and 50°C. Furthermore, the gas turbine heat rate improvement landed at 6.5% at 50°C and 5% air injection.\u0000 This study also compares the waste heat recovery system with other power augmentation technologies, namely the inlet mechanical chiller and the evaporative cooler.\u0000 Compared to a gas turbine with waste heat recovery turbocharger air injection system at 5% air injection, the electrical chiller system increases the gas turbine heat rate by around 2% assuming chiller COP of 5.\u0000 The waste heat recovery turbocharger system offers both power augmentation and heat rate improvements for simple cycle gas turbines. Additionally, this system can extend the hot gas path life by lowering the firing temperature without losing power.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"191 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121736808","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Liquid Air Combined Cycle","authors":"W. Conlon, Milton Venetos, Aaron M. Rimpel","doi":"10.1115/gt2022-80426","DOIUrl":"https://doi.org/10.1115/gt2022-80426","url":null,"abstract":"\u0000 Hybrid integration of thermal energy storage with gas turbines can provide compact, cost-effective, long-duration energy storage while reducing the fuel consumption of dispatchable resources needed for the reliability of renewable dominant electric grids. The Liquid Air Combined Cycle™ (LACC) is a hybrid energy storage system using cryogenic liquid air as an energy storage medium and gas turbine exhaust heat to extract stored energy.\u0000 The storage tank is charged using liquefaction processes employing electric motor-driven compressors to pressurize the air, heat exchangers to reject heat of compression, and expanders to reduce the temperature and liquefy the air. Proven cryogenic refrigeration processes can be selected based on capital cost (per kg/s of liquid air produced), efficiency (kJ per kg of air produced), and operating factors including startup speed and load following capability.\u0000 This paper presents results of studies undertaken for the U.S. Department of Energy to evaluate cost and performance tradeoffs for charge and discharge cycle components, optimize charge and discharge cycles, and assess the techno-economic potential of LACC technology.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131072140","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Organic Rankine Cycle Turbine and Heat Exchanger Sizing for Liquid Air Combined Cycle","authors":"Owen M. Pryor, Aaron M. Rimpel, W. Conlon","doi":"10.1115/gt2022-82263","DOIUrl":"https://doi.org/10.1115/gt2022-82263","url":null,"abstract":"\u0000 Cryogenic energy storage offers several opportunities to design turbomachinery and other equipment for novel cycles. This paper presents the design and analysis of turbomachinery and heat exchangers for an Organic Rankine Cycle (ORC) subsystem for a hybrid energy storage concept. The Liquid Air Combined Cycle is an energy storage system that stores air at cryogenic conditions at times with high variable renewable energy to be dispatched along with a gas turbine to recover the exhaust heat. In order to re-vaporize the air, the liquid air is coupled with an ORC as an additional bottoming cycle. The ORC turbine is expected to expand the fluid with a pressure ratio of nearly 30 and a flow rate of approximately 45 kg/s. Sizing calculations for both a radial and axial turbine solution were performed over a range of speeds and stages to determine the optimal design point. The results show that either an axial (8- or 9-stage) or radial (four stages at two shaft speeds) turbine are capable of handling the pressure ratios. Further trades of the two configurations would be required to determine the best option. The ORC system also incorporates five heat exchangers to distribute heat, vaporize the liquid air, or recover exhaust heat from the gas turbine. Three heat exchangers were analyzed to understand the size of heat exchangers and pressure drop for the overall system. Different types of heat exchangers were explored for the different purposes, including plate-fin heat exchangers, gasketed plate heat exchangers and shell-in-tube heat exchangers. It was determined that the ORC recuperator, liquid-air vaporizer, and vaporized air pre-heater would be counter-flow heat exchangers using a gasketed plate design.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"59 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130971381","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The Pump-Turbine Selection Approach for Geomechanical Storage Facility","authors":"Abhay V. Patil, Bunker Hill, Jason C. Wilkes","doi":"10.1115/gt2022-83146","DOIUrl":"https://doi.org/10.1115/gt2022-83146","url":null,"abstract":"\u0000 The geo-mechanical hydro-storage method utilizes the natural energy storage capability of subsurface formations to store water under pressure. The pumps supply water underground and store it in-between layers of low permeability formations. The natural elasticity of the rock holds the water under pressure. The pressurized water is released through a turbine to produce electricity to send back to the grid. The proven capability to cycle hydraulic power across a broad range of geographies for long duration energy storage makes this method attractive. However, with the proposed pumped storage concept, the storage capacity and head availability requirements change as compared to conventional hydro storage facilities due to specific limitations with well-size (flow rate) and underground formation. The current study focuses on exploring different pump and turbine options for the given operating conditions and developing a way forward to qualify the pump and turbine for specific operational conditions based on cost, performance, and reliability. Pump options include centrifugal and plunger pumps, while turbine options include Pelton and Francis or Centrifugal Pump as Turbine. Three configurations are proposed based on initial cost and round-trip efficiency values. A metric Levelized Cost of Stored Energy (LCOSE) is utilized to compare the performance of different options, considering 25 years of overall life span. A sensitivity study was applied to chosen configurations and sizes for different roundtrip efficiencies and projected initial costs. Within given bounds, operational conditions, and assumptions made, the study outputs Pump-as-Turbine (PaT) as an optimal solution for the proposed conditions.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"4 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125834775","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Simulation of the HiPowAR Gas-Steam Power Generation System Using Ammonia as Fuel","authors":"A. Cammarata, P. Colbertaldo, S. Campanari","doi":"10.1115/gt2022-81982","DOIUrl":"https://doi.org/10.1115/gt2022-81982","url":null,"abstract":"\u0000 This work presents a simulation activity on an innovative power generation cycle, developed within the EU Horizon 2020 project HiPowAR, using ammonia as fuel for an oxy-combustion process in a membrane reactor. The key advantages of the system are the low compression requirement, typical of steam cycles, and the large expander inlet temperature, typical of gas turbine cycles. The analysis explores the options of cooled or uncooled expander, either adopting a steam-cooled turbine made of conventional Ni-based alloys or using high temperature-resistant ceramic matrix composite (CMC) materials. The simulations show that, with a reactor outlet temperature of 1350°C, a cooled system could reach up to 48.2% efficiency, with limited additional advantages when further increasing the temperature. At the same temperature level, the uncooled system could instead achieve 52.5% efficiency, allowing also a substantial system simplification. However, since the expanded mixture contains nearly 90%mol steam, the use of CMC materials is made difficult by degradation issues and would require the development of suitable barrier coatings.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"5 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121476094","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Purushothaman, Avinash Renuke, A. Sorce, A. Traverso
{"title":"A Review of Pressure Gain Combustion Solutions for Aerospace Propulsion","authors":"S. Purushothaman, Avinash Renuke, A. Sorce, A. Traverso","doi":"10.1115/gt2022-83799","DOIUrl":"https://doi.org/10.1115/gt2022-83799","url":null,"abstract":"\u0000 Recent developments in Pressure Gain Combustion (PGC) technology have demonstrated its ability to achieve higher thermal efficiencies and lower carbon emissions as compared to conventional gas turbine counterpart working in Brayton cycle. Ongoing studies suggest the possibility of implementing PGC in aircraft engines by replacing the high-pressure section (HP compressor, combustion chamber and HP turbine) with a PGC system. This, coupled with research on advanced materials and cooling solutions, offers the potential for higher overall gas turbine efficiency and fuel economy, contributing towards emission reduction of the aviation sector.\u0000 This paper aims at a comprehensive review of PGC technology solutions applied in the area of aero propulsion. Reported background covers the historic as well as ongoing research activities at the component level, the cycle level, and the propulsion application of Pulse Detonation Engine (PDE), Rotating Detonation Engine (RDE), Oblique Detonation Wave Engine (ODWE), Free Piston Composite Cycle Engine (FP-CCE), and wave rotor engines. The analytical, numerical, and experimental research work is reviewed, providing also a comparison of PGC engine conceptual designs with existing gas turbine engines used in aerospace propulsion.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116681462","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Joshua Schmitt, Noemi Collado, A. Swanger, M. Otto, J. Kapat
{"title":"Techno-Economic Analysis of a Cryogenic Flux Capacitor for Grid Storage","authors":"Joshua Schmitt, Noemi Collado, A. Swanger, M. Otto, J. Kapat","doi":"10.1115/gt2022-83375","DOIUrl":"https://doi.org/10.1115/gt2022-83375","url":null,"abstract":"\u0000 The Cryogenic Flux Capacitor (CFC) is a cold, dense fluid storage core with integrated design features that afford the designer flexibility and provide new possibilities for the storage and discharge of energy. The stored energy, in this case, is represented by hydrogen physically bonded within the nanoscale pores within the aerogel composite blanket material, and the process of bonding or debonding is governed by principles of physical adsorption (physisorption) and thermodynamics. The large surface area afforded by the nanoporous aerogel (∼1,000 m2/g) allows for storage densities close to, or in some cases exceeding, that of normal boiling point liquids. Its performance easily exceeds what can be achieved via ambient temperature, high-pressure gas storage for an equivalent volume. CFC storage is predicted to be easily scalable, is constructed from readily available commercial materials, lends itself to a range of pressure applications, and is geometry insensitive.\u0000 The high energy density of CFC-stored hydrogen allows long durations of storage, such as daily to monthly cycling, which corresponds to approximately 10 to 100 hours of duration, respectively. The techno-economic analysis examines different types of hydrogen storage for commercial viability. The assessment includes the use of hydrogen blended with natural gas in a combined cycle gas turbine. The study provides results for a range of blends from 100% natural gas to 100% hydrogen. The required fuel usages are estimated for the intended application in a grid scenario that features large amounts of renewable penetration, 10 hours, and as a baseload, 100 hours.\u0000 The study presents preliminary estimates of the capital cost of storage and operating cost of storage. In addition, the cost of firing natural gas and capturing the carbon dioxide (CO2) in a carbon capture and sequestration (CCS) system is assessed. Based on the study, it is shown that CFC can competitively meet performance and cost needs for grid-based energy storage.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"24 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114988390","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
G. F. Frate, M. Pettinari, Emanuele Di Pino Incognito, Riccardo Costanzi, L. Ferrari
{"title":"Dynamic Modelling of a Brayton PTES System","authors":"G. F. Frate, M. Pettinari, Emanuele Di Pino Incognito, Riccardo Costanzi, L. Ferrari","doi":"10.1115/gt2022-83445","DOIUrl":"https://doi.org/10.1115/gt2022-83445","url":null,"abstract":"\u0000 The need for storage capacity is continuously increasing due to the progressive penetration of renewable energy sources in the power grids. New storage technologies for large-scale applications are emerging in this context, among which Pumped Thermal Electricity Storage (PTES) is a promising alternative. PTES is based on closed Brayton cycles: a Brayton heat pump is operated in the charging phase, using the off-peak electricity to transfer heat between two reservoirs. A Brayton heat engine is operated between the same reservoirs in the discharging phase, producing electric energy. The purpose of grid-scale storage facilities is to provide flexibility to the grid. Therefore, the proposed technologies must effectively operate in part-load conditions and quickly react when the load must be adjusted. In this study, the transient response of the Brayton PTES technology is studied, with particular emphasis on its off-design operation and control strategy. To this end, a detailed thermodynamic model of the system is developed. Particular attention is given to the sizing of the components relevant to the control. Furthermore, a control strategy suited for the power regulation of closed Brayton cycles, the Inventory Control, is investigated, and implementation is proposed. As it resulted, the system can operate in part-load with negligible performance degradation and is characterized by a rapid transient response. Therefore, Brayton PTES resulted as a promising storage technology for grid-scale applications.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"49 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121693973","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Salvatore Guccione, S. Trevisan, R. Guédez, Björn Laumert, Simone Maccarini, A. Traverso
{"title":"Techno-Economic Optimization of a Hybrid PV-CSP Plant With Molten Salt Thermal Energy Storage and Supercritical CO2 Brayton Power Cycle","authors":"Salvatore Guccione, S. Trevisan, R. Guédez, Björn Laumert, Simone Maccarini, A. Traverso","doi":"10.1115/gt2022-80376","DOIUrl":"https://doi.org/10.1115/gt2022-80376","url":null,"abstract":"\u0000 High-efficient supercritical CO2 (sCO2) power blocks and the hybridization with solar photovoltaic (PV) plants have been identified as two viable solutions to enhance the economic competitiveness of Concentrating Solar Power (CSP) plants. This work introduces an innovative hybrid PV-CSP system layout with molten salt thermal energy storage and a sCO2 power block. An active hybridization has been proposed employing a molten salt electric heater that allows storing the excess PV production as thermal energy. The scalability of the plant has been investigated using size-dependent cost functions and introducing a novel methodology for scaling the sCO2 turbomachinery efficiencies. The conducted techno-economic optimizations show that the proposed hybrid PV-CSP plants can be cost-competitive. For a European solar resource location - 1900 kWh/(m2yr) - Levelized Cost of Electricity (LCOE) values lower than 66 EUR/MWh and capacity factors higher than 70 % can be achieved at 100 MWe. For a high-irradiance location - 3400 kWh/(m2yr) - a capacity factor of 85 % and a LCOE of 46 EUR/MWh have been found for the same scale. The selection of the sCO2 power cycle has a marginal impact on these results so that a simple recuperated cycle can yield similar LCOEs as the recompressed, reheated, and intercooled layouts. For smaller scales, systems with large gaps between the PV and CSP capacities are preferred, laying the optimal conditions for the electric heater integration with utilization factors up to 21 %.","PeriodicalId":217779,"journal":{"name":"Volume 4: Cycle Innovations; Cycle Innovations: Energy Storage","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129491431","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}