Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science最新文献_第7页

Analysis investigation of the influence of sub-surface shear stress distribution of spur gear 直齿轮表面下剪应力分布影响的分析研究

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241261895

Wenzheng Liu, Rupeng Zhu, Wenguang Zhou, Jingjing Wang

引用次数: 0

Vibration characteristics of a rotating flywheel-flexible coupling system with misalignment fault: Experiment and simulation 存在不对中故障的旋转飞轮-弹性联轴器系统的振动特性：实验与模拟

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241266319

Zhiwei Liu, Qiong Wang, Hanqing Guan

{"title":"Vibration characteristics of a rotating flywheel-flexible coupling system with misalignment fault: Experiment and simulation","authors":"Zhiwei Liu, Qiong Wang, Hanqing Guan","doi":"10.1177/09544062241266319","DOIUrl":"https://doi.org/10.1177/09544062241266319","url":null,"abstract":"To avoid harmful and even catastrophic influences on internal combustion engine-generator set, it is essential to investigate early faults such as misalignment, rotor rubbing, shaft cracks, and bearing faults. To study the effect of the misalignment of the elastic coupling on vibration characteristics of the rotor system, experiment with different misalignment amplitudes and types is carried out on a flywheel-elastic coupling rotor test rig. Vibration responses of the rotor system with different amplitudes of parallel and angular misalignment are illustrated by amplitude frequency response curves, orbit plots and frequency spectra. Super-harmonic resonance phenomenon is revealed. Based on the misalignment of the high elastic coupling, dynamical equations of a generator rotor system, excited also by unbalanced magnetic pull and mass unbalance, are derived using the energy method and numerically investigated by the Runge-Kutta method. The theoretical results are in good accordance with the experimental ones. Besides, a new phenomenon of the flywheel-elastic coupling vibration system is found in the experiment.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782926","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Research on six-joint industrial robotic arm positioning error compensation algorithm based on motion decomposition and improved CIWOA-BP neural network 基于运动分解和改进型 CIWOA-BP 神经网络的六关节工业机器人手臂定位误差补偿算法研究

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241264706

Xuejian Zhang, Xiaobing Hu, Hang Li, Zheyuan Zhang, Haijun Chen

{"title":"Research on six-joint industrial robotic arm positioning error compensation algorithm based on motion decomposition and improved CIWOA-BP neural network","authors":"Xuejian Zhang, Xiaobing Hu, Hang Li, Zheyuan Zhang, Haijun Chen","doi":"10.1177/09544062241264706","DOIUrl":"https://doi.org/10.1177/09544062241264706","url":null,"abstract":"Motion errors in the trajectory of a six-joint industrial robotic arm’s end-effector can significantly impact machining precision. Complex milling operations can lead to deviations from the intended path due to the robotic arm’s structural characteristics. These errors often exhibit periodic and position-dependent variations, underscoring the need for meticulous control measures. To address this challenge, we propose a novel motion decomposition-based error compensation technique for a six-joint industrial robotic arm. This approach involves breaking down the robot’s motion trajectory into distinct components and constructing prediction models for each component using a BP neural network. These models are then optimized using the Whale Optimization Algorithm (CIWOA) and an adaptive chaotic mapping clustering approach to improve efficiency and global optimization. The proposed method is applied to various motion types of the robotic arm, resulting in substantial enhancements in absolute positioning accuracy. Experimental validation confirms the reliability of the CIWOA-BP neural network prediction model and the effectiveness of the nonparametric accuracy compensation method in refining motion planning precision.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782878","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Investigation on mechanical properties of bronze infill PLA composite fabricated by fused deposition modelling 熔融沉积建模法制造的青铜填充聚乳酸复合材料力学性能研究

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241262255

K. Ravi Kumar, K. Sivavel Annamalai, H. Sriram, Nisha Soms

{"title":"Investigation on mechanical properties of bronze infill PLA composite fabricated by fused deposition modelling","authors":"K. Ravi Kumar, K. Sivavel Annamalai, H. Sriram, Nisha Soms","doi":"10.1177/09544062241262255","DOIUrl":"https://doi.org/10.1177/09544062241262255","url":null,"abstract":"This study is on the mechanical properties of bronze infill poly lactic acid composites fabricated by fused deposition modelling. By changing the nozzle temperature, printing speed, layer thickness and infill density the mechanical properties of the composites were studied. Tensile, flexural and impact strength tests were conducted on the composite specimen. Mathematical models were developed using response surface methodology and the significance of the models was tested using analysis of variance. Increase in infill density and nozzle temperature increased the strengths of the composites. Increase in layer thickness and printing speed decreased the strengths of the composite specimen. Tensile strength is primarily influenced by infill density (38.82%), flexural strength is primarily influenced by Nozzle Temperature contributes (44.02%) while Infill density (58.12%) plays the major role in contributing the impact strength followed by other parameters. The highest tensile strength, flexural strength, impact strength values obtained in this study are 19.3 (N/mm2), 36.08 (N/mm2) and 0.26 (kJ/m2) respectively. The mechanism of the fractured specimen was investigated using scanning electron microscopy. Fracture mechanisms such as cracks, infill gaps, voids, interface, delamination, hillocks, particle pull out, delamination had an effect on the fracture of composite specimens.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782932","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Enhancing efficiency and accuracy in robotic assembly task planning through tool integration using a hybrid class topper optimisation algorithm 使用混合类顶层优化算法，通过工具集成提高机器人装配任务规划的效率和准确性

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241264708

Chiranjibi Champatiray, MVA Raju Bahubalendruni, Golak Bihari Mahanta, Duc Truong Pham, Rabindra Narayan Mahapatra

{"title":"Enhancing efficiency and accuracy in robotic assembly task planning through tool integration using a hybrid class topper optimisation algorithm","authors":"Chiranjibi Champatiray, MVA Raju Bahubalendruni, Golak Bihari Mahanta, Duc Truong Pham, Rabindra Narayan Mahapatra","doi":"10.1177/09544062241264708","DOIUrl":"https://doi.org/10.1177/09544062241264708","url":null,"abstract":"Uncertainties in robotic assembly can substantially influence the quality of assembly task planning, often resulting in suboptimal solutions. It is crucial to account for these uncertainties when developing assembly task plans that are both efficient and practical for multi-part products. To address such issues, the proposed method integrates the NelderMead simplex algorithm with the Class Topper Optimisation Algorithm to create a hybrid NelderMead Class Topper Optimisation Algorithm. This study uses a vibration generator as an example to illustrate the application of the proposed method. Ensuring tool accessibility is emphasised, and the assembly tasks are initialised accordingly. The feasibility of these tasks is determined using liaison and tool-integrated geometric feasibility predicate analysis. Multiple criteria are considered to achieve the most efficient robotic assembly task planning, including part reorientation, gripper or tool change and the energy required to assemble the part. The effectiveness and robustness of the proposed optimisation algorithm are demonstrated by comparing it with other algorithms, such as the teaching-learning-based algorithm, the genetic algorithm, the bees algorithm and the particle swarm optimisation algorithm. The results have shown that the proposed approach is highly effective for real-industrial relevant problems.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782880","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Mechanical and microstructural investigation of three-dimensionally printed PEEK polymer 三维打印 PEEK 聚合物的机械和微结构研究

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241264950

Chithambaram Karunanithi, Senthilnathan Natarajan

{"title":"Mechanical and microstructural investigation of three-dimensionally printed PEEK polymer","authors":"Chithambaram Karunanithi, Senthilnathan Natarajan","doi":"10.1177/09544062241264950","DOIUrl":"https://doi.org/10.1177/09544062241264950","url":null,"abstract":"Three-dimensional polymer printing is becoming more popular due to its effectiveness in creating components of any geometric design. Polymer materials can be used at low temperatures but are weaker than other functional materials. Polyetheretherketone (PEEK) is a thermoplastic with outstanding mechanical properties that can tolerate high temperatures. A high-temperature fused deposition modeling machine manufactured PEEK specimens in this experiment to find the ideal printing parameters S1, S2, S3, and S4 were made using varying printing speeds and layer thicknesses. The polymer sample’s exterior surface was analyzed using FESEM, while physical characterization was conducted through X-ray diffraction analysis and water contact angle measurement. The strength of each sample in the relevant variables was determined using mechanical testing, such as tensile and compression tests. It was found that specimen S3 having a layer thickness of 0.15 mm and printing speed of 20 mm/s showed a high tensile and compressive strength value of about 78 and 144 MPa respectively than the other three samples. In addition, the fractured tensile samples were analyzed with scanning electron microscopy to discover the factors that contributed to the disparity in the values of their strengths.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782883","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Experimental and numerical investigation of monolithic and homo-stacked target plates of AA2014-T6 subjected to blunt and hemispherical projectiles AA2014-T6 单片和同层靶板在钝头和半球形射弹作用下的实验和数值研究

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241263413

Anoop Kumar Pandouria, Rohit Kumar, Kuldeep Yadav, Purnashis Chakraborty, Vikrant Tiwari

{"title":"Experimental and numerical investigation of monolithic and homo-stacked target plates of AA2014-T6 subjected to blunt and hemispherical projectiles","authors":"Anoop Kumar Pandouria, Rohit Kumar, Kuldeep Yadav, Purnashis Chakraborty, Vikrant Tiwari","doi":"10.1177/09544062241263413","DOIUrl":"https://doi.org/10.1177/09544062241263413","url":null,"abstract":"In this article, the ballistic response of thin sheets of the aluminium AA2014-T6 in monolithic and homo-stacked configurations was studied experimentally and numerically. Firstly, the experiments were performed on 1 and 2 mm thick monolithic and 1 + 1 mm homo-stacked target plates with blunt and hemispherical nose shape projectiles at different velocities. All experiments were carried out using a single stage gas gun coupled with two ultra-high-speed cameras. Transient response and full-field out-of-plane displacement of the target plates are analysed using 3D digital image correlation technique (3D-DIC). During the investigations the nose shapes of the projectile were found to have a significant influence on both out-of-plane displacement and failure mode of the impacted plates. The target plate is penetrated by shear plugging in the event of a blunt projectile, whereas for a hemispherical projectile impact, penetration occurred from first tensile stretching and then shear plugging. It was also found that the ejected plug and hole size are almost the same and equal to the projectile’s diameter for blunt projectiles. While in case of hemispherical impact both were less than the projectile’s diameter. Secondly, 3D FE simulations for all the configurations were also performed using J-C plasticity and damage criteria. The simulation results were found to be in accordance with the experimental results in terms of failure mode, ejected plug size and plate hole size. Detailed Russel error analysis was also performed to validate the correlation between the experimental and numerical data.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782652","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Mechanical comprehensive evaluation model and sealing performance research of rubber cylinder at large pressure and high temperature 橡胶气缸在大压力和高温下的力学综合评价模型和密封性能研究

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241261252

Lan Zhang, Jing Wen, Hang Zhang, Guoqiang Zhang, Ming Liu, Feihong Yun, Shoubo Shang

{"title":"Mechanical comprehensive evaluation model and sealing performance research of rubber cylinder at large pressure and high temperature","authors":"Lan Zhang, Jing Wen, Hang Zhang, Guoqiang Zhang, Ming Liu, Feihong Yun, Shoubo Shang","doi":"10.1177/09544062241261252","DOIUrl":"https://doi.org/10.1177/09544062241261252","url":null,"abstract":"The submarine pipe stopper is prone to failure at large pressure and high temperature conditions. This work focuses on the submarine pipe stopper’s sealing failure caused by excessive shear stress and high temperature. First, the working principle of the sealing device in the stopper was analyzed and its performance was verified through land and sea trials. Then a comprehensive evaluation model fit for the large working pressure was established by analyzing the rubber cylinder’s sealing performance and strength. Next, the model was modified by simulation using the nitrile rubber (NBR) cylinder and the fluororubber (FKM) cylinder were used as examples to revise the comprehensive evaluation model while taking temperature into account. The maximum contact stress and the maximum shear stress of the NBR rubber cylinder at 100°C increased by 28% and 30.62% compared to 25°C, and that of the FKM rubber cylinder increased by 24% and 26.12%. In comparison to 25°C, the maximum contact stress and maximum shear stress of the NBR rubber cylinder increased by 28% and 30.62% at 100°C, while the FKM rubber cylinder had an increase of 24% and 26.12%. At 100°C, the NBR rubber cylinder exhibits a maximum contact stress of 4.71 MPa and a maximum shear stress of 1.18 MPa, whereas the FKM rubber cylinder displays maximum contact and shear stresses of 5.09 and 2.44 MPa. Finally, the rubber cylinder’s maximum working pressure at different temperatures was derived, and the influence of its parameters was discussed. The maximum working pressure at 100°C is only 21% of what the rubber cylinder can bear at 25°C. This work is of great significance for accurately evaluating the rubber cylinder’s sealing performance in the submarine pipe stopper and provides new ideas for the rubber cylinder’s design at high-temperature conditions.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782876","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Multi-objective trajectory planning and implementation of a metamorphic palletizing robot 变形码垛机器人的多目标轨迹规划与实施

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-26 DOI: 10.1177/09544062241263411

Rugui Wang, Ningjuan Zhao, Yichen Dong, Lin Li, Zhipeng Fan

{"title":"Multi-objective trajectory planning and implementation of a metamorphic palletizing robot","authors":"Rugui Wang, Ningjuan Zhao, Yichen Dong, Lin Li, Zhipeng Fan","doi":"10.1177/09544062241263411","DOIUrl":"https://doi.org/10.1177/09544062241263411","url":null,"abstract":"This paper focuses on a metamorphic palletizing robot, elaborating on its working principles and analyzing its working trajectory. The primary aim is to address the complex challenge of multi-objective trajectory planning during the robot’s motion, with a focus on minimizing time, energy consumption, and jerk. We present a general formula for optimizing multiple objectives, taking into account transformation characteristics based on actual working conditions. The optimization process employs the Non-dominated Sorting Genetic Algorithm with an elite strategy (NSGA-II), while Particle Swarm Optimization (PSO) is integrated into the optimization progression to identify specific metamorphic points. This approach ultimately produces a set of Pareto optimal solutions. From this set, the solution with the lowest time consumption is chosen as the definitive option for multi-objective planning. The joint driving functions of the robot during configuration transformations and within each configuration are analyzed accordingly. To ensure precision, the joint driving functions employed in the experiment are fine-tuned with pulse compensation values. Subsequently, experimental validation is carried out to verify the accuracy and practical feasibility of the multi-objective trajectory planning method.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141783042","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0

Hand anthropometrics from radiograms of Italian women: A population-specific ergonomic design procedure 从意大利女性的放射线照片中得出的手部人体测量数据：针对特定人群的人体工程学设计程序

IF 2 4区工程技术

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Pub Date : 2024-07-25 DOI: 10.1177/09544062241258073

Alberto Dal Maso, Francesca Cosmi

{"title":"Hand anthropometrics from radiograms of Italian women: A population-specific ergonomic design procedure","authors":"Alberto Dal Maso, Francesca Cosmi","doi":"10.1177/09544062241258073","DOIUrl":"https://doi.org/10.1177/09544062241258073","url":null,"abstract":"To design a comfortable hand support, the population-specific morphological characteristics of human hands must be known. Surface and bone anthropometric data from 177 radiograms of the left hands of an unselected sample of 87 subjects (training set) belonging to the Italian, female population (age 58 ± 12) were collected. Hand Length (HL) and Hand Width (HW) were respectively 172 ± 8 mm and 81 ± 4 mm; Hand Bone Length (HBL) was 179 ± 8 mm. A separate validation set consisting of 25 radiograms from 25 patients belonging to the same population was also collected. Bone and surface measurements were compared to validate the relationships proposed by Kong et al. Their approach applied to the validation set resulted in errors between 3.1% and 8.7%, which is almost as accurate (low bias) but somewhat less precise (higher mean errors) than what found by Kong et al. on their own sample belonging to the Korean population. Two methods were developed to predict the positions of the Metacarpo-phalangeal joints of the Index, Middle, and Ring fingers with reference to the Index-Middle interdigital crotch: method PM, based on the population mean, and method PR, which also considers the Hand Width. The overall average estimation error for method PM is 1.87 mm, while for method PR it is 1.69 mm. Method PR compared to method PM improves the precision by up to 32% in the x direction and 3% in the y direction. Based on these results, a 3D CAD hand model representing the target population was developed, which can be used for the design of population-specific ergonomic medical devices.","PeriodicalId":20558,"journal":{"name":"Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science","volume":null,"pages":null},"PeriodicalIF":2.0,"publicationDate":"2024-07-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141782935","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 0