{"title":"Evolution of AuSnx Intermetallic Components in Laser Reflowed Right-angled Solder Joints during Isothermal Aging Process","authors":"Liu Wei, Wang Chunqing, Tian Yanhong, L. Mingyu","doi":"10.1109/ICEPT.2006.359868","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359868","url":null,"abstract":"Au surface finish is common used as a protection layer on pads. In the traditional reflow process, Au will be dissolved into solder and form AuSn4 IMCs (intermetallic components). However, as for the solder joints fabricated by laser soldering, the morphology and distribution of the AuSnx IMCs are quite different from that in solder joints fabricated by traditional reflow methods. The formation, distribution and evolution of IMCs will affect the properly and reliability of solder joints directly. This paper presents a detailed analysis of AuSnx IMCs evolution in laser reflowed solder joints during isothermal aging process. To investigate the effect of Au thickness on the evolution of AuSnx IMCs, pads with 0.1, 0.5, 0.9 or 4.0 mum Au surface finish were introduced into our experiment. The solder joints were aged in the 125 degC isothermal oven. Experiment results showed that few IMCs formed at the interface of the solder and the pad with 0.1mum Au surface finish. Even in the condition of 31 days aging, the thickness of IMCs didn't increase a lot; as for the laser reflowed solder joints with 0.5 or 0.9mum Au surface finish on the pad, most of the AuSn4 IMCs stayed at the interface and formed in needle-like or dendritic morphology. With the increase of aging time, the AuSn4 IMCs became more flat and changed to a continuous layer; In the laser reflowed solder joints with 4.0mum Au surface finish on the pad, AuSn, AuSn2, AuSn4 IMCs and Au2Sn phase formed at the interface. With the increase of aging time, more Sn rich IMCs formed at the interface, and evolved to AuSn4 IMCs in the condition of long time aging. The thickness of AuSn4 IMCs can reach about 30mum","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"225 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122428662","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Solder Joint Thermal Fatigue Analysis of 48-FBGA","authors":"Song Chen, Taekoo Lee, Jaisung Lee, Nufeng Feng","doi":"10.1109/ICEPT.2006.359816","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359816","url":null,"abstract":"A three-dimensional finite element model has been developed to study the solder joint reliability of 48-1/0 fine pitch ball-grid-array (FBGA) assembly. Anand model was selected to describe the 62Sn36Pb2Ag creep behavior. Sub-modeling technique was used to transfer the displacements to the local model for a detailed analysis under thermal cycling conditions. Solder ball visco-plastic energy accumulated per temperature cycle was applied in this BGA product to predict the fatigue life. In addition, the effect of PCB thickness was pointed briefly","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122800655","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Investigation of Thermal-Mechanical and Moisture Driven Delamination in Lead-free QFN Packages during SMT Reflow Soldering Process","authors":"X. Su, H. Luo, D.G. Yang","doi":"10.1109/ICEPT.2006.359847","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359847","url":null,"abstract":"Interface delamination is one of the major failure modes in plastic IC packages. The encapsulating polymers used in electronic packaging are characteristic of high porosity, which makes the material susceptible to the moisture absorption. During reflow soldering process, the entire package is exposed to the soldering temperature as high as 260degC for lead-free solders. Under such temperatures, moisture absorbed by polymer materials evaporates, generating high internal vapor pressures in the voids. Interface delamination may be caused by the combined effect of the thermomechanical stress, hygromechanical stress and vapor pressure. The main objective of this paper is to investigate the effects of temperature, moisture diffusion and vapor pressure on the delamination in lead-free QFN package during SMT reflow soldering process. Finite element simulation on a plastic QFN package is carried out for the entire thermal and moisture history from the JEDEC Level 1 moisture preconditioning (85degC/85%RH for 168 hours) to subsequent exposure to a lead-free soldering process. The energy release rate due to thermal stress, hygro-stress and vapor pressure is computed and studied by using J-integral method. The result shows that the additional mismatch induced by the vapor pressure and moisture in the package is of the same order as the CTE mismatch, which has a quite significant effect on interfacial delamination failure","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"87 42 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130378844","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Analysis of Dark Stain on Chip Surface of High-Power LED","authors":"Fan Wu, Yiping Wu, B. An, Feng-shun Wu","doi":"10.1109/ICEPT.2006.359785","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359785","url":null,"abstract":"In the process of aging or in service of some high power blue LEDs, dark stain may occur on the LED chip surface, which cast a shadow over the chip and thus led to the losing of luminous flux. In the degraded samples, it was found that firstly the dark stain was formed on the chip surface equably, and then the color of this stain gradually darken with time. In this paper, this kind of dark stain was detected and analyzed. The morphology of the dark stain and the elements contained in it were measured by scanning electron microscopy (SEM) and energy dispersive analysis by X-ray (EDAX), respectively. A large mount of oxygen and carbon were found in the black zones, which implied that some chemical reactions occurred on the interface. After we removed the black materials off the chip surface, the quantity of luminous flux evidently increased. The origin of oxygen and the possible reason of the dark stain were also discussed","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"127 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126874319","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A Base Exciter for Dynamic Testing of MEMS on Wafer Level","authors":"Yang Shi, Honghai Zhang, Xuefang Wang, Sheng Liu","doi":"10.1109/ICEPT.2006.359769","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359769","url":null,"abstract":"With the rapid development of micro-electro-mechanical system (MEMS), it is indispensable to investigate dynamic characteristics of MEMS. Characteristics of conventional modal testing technology includes excitation of the structure via a function of known frequency characteristics using an impact hammer or an exciter, and measuring the associated response using force or motion sensors. Due to small size & ultra high frequency of MEMS, however, conventional modal testing methods cannot be directly applied to microstructures. A salient feature of modal testing of MEMS is non-contact. With application of wafer bonding, dynamic testing of MEMS on wafer level becomes very important. A base exciter for dynamic testing of MEMS on wafer level is described in this paper. The performance of the base exciter is investigated via experiments","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"11 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114332864","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Increasing Value in Lead-Free Soldering with Nitrogen","authors":"H. Ling, P. Stratton","doi":"10.1109/ICEPT.2006.359733","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359733","url":null,"abstract":"Many of the lead-free solder pastes on today's market claim either not to require the use of nitrogen inerting or to work equally well in air or nitrogen. There is a fine balance between a lead-free solder paste that performs well in air and one where the flux residue must be removed to avoid corrosion problems. Even the best pastes are close to their operating limit so that a small narrowing of the soldering window results in poor joint quality. One leading Asian consumer electronics manufacturer found that the best performing paste was also expensive. Trials were carried out to see whether the overall cost of the best solder paste reflowed in air would be less than the cheapest paste reflowed in nitrogen while maintaining the highest level of product quality. Commercial boards were reflowed using four different solder pastes in air and nitrogen. The resulting boards were visually inspected for joint quality. The results showed that not only did nitrogen inerting improve the quality of the joints produced by the best paste, but it could bring the cheapest paste up to that standard as well. The overall processing cost of the best paste reflowed in air was higher than that for the lowest cost paste reflowed in nitrogen, maximizing value","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"30 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124119790","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Modeling for Solder Self-Assembly of MEMS Microstructure Powered by Surface Tension","authors":"K. Pan, Yilin Yan, Bin Zhou, Lipu Wei","doi":"10.1109/ICEPT.2006.359789","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359789","url":null,"abstract":"Due to the characteristics of miniaturization of size and high integration of functions and so on, MEMS is taken as high-tech frontier of 21st century. The progress of surface micromachining and bulk micromachining promotes MEMS technology. But, the inherent defects of surface micromachining and bulk micromachining hinder the triumphant manufacture of complex three-dimensional. Surface tension powered MEMS self-assembly can deal with this \"bottle neck\" successfully. Self-assembly technology is based on the principle of surface energy minimization of molten material. During the process of minimizing the surface energy, surface tension may pull the horizontal hinge plate up to some angle and then achieve equilibrium state. In this paper, finite element method is employed, a new dynamic MEMS self-assembly model is developed by SURFACE EVOLVER. The model in this paper can dynamically simulate the angle change of microstructure during the process of evolvement. The main characteristics of this model are: (1) it is easier to obtain the final angle than static model for a certain volume of solder paste. (2) Under the condition of no change of parameters, such as solder paste volume, pad size and pad figure, the final angle may be more precise compared with the results of previous researches. It can provide guarantee to precisely control the final assembly angle of hinge plate. Designs of experiments are planned and the solder geometry shapes are estimated from this dynamic model, and the area, energy and forces are derived correspondingly. Further, the relationship between the solder parameters and the angle, energy and forces are conducted from the above results. From the experiments we can conclude that pad size and solder volume are critical parameters which influence the final assembly angle. The experimental results can be used to guide the design of the self-assembly for 3D MEMS microstructures","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"2015 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127684382","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Fengshun Wu, Mingmin He, Yiping Wu, B. An, Weigang Zhang
{"title":"Effect of Interfacial IMCs Proportion on the Reliability of Miniature Lead-Free Solder Joint","authors":"Fengshun Wu, Mingmin He, Yiping Wu, B. An, Weigang Zhang","doi":"10.1109/ICEPT.2006.359754","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359754","url":null,"abstract":"The effect of interfacial IMCs (intermetallic compounds) proportion on the reliability of miniature lead-free solder joint was studied. The miniature lead free solder joint was formed with Sn-3.5Ag-0.5Cu or Sn-3.5Ag solder alloys and two copper bars that the ends were plated with Ni and Au. Several sizes of micro-joints were gotten to measure the effect of IMCs proportion. Optical microscope (OM) was used to observe the changes of interfacial IMCs of different miniature joints. Maximal shear strength force and maximal impact force were tested to evaluate the effect of miniaturization on the reliability. The results showed that the interfacial IMCs proportion of solder joints increased when they were aged at 150degC for 0 hours, 120 hours, and 200 hours or the sizes of solder joints changed from 100 mum to 20 mum. The maximal shear strength and maximal impact force of the solder joints decreased when the interfacial IMCs proportion increased","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"24 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126397290","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The Optimization of Reflow Soldering Temperature Profile Based on Simulation","authors":"Yu-bing Gong, Quanyong Li, D.G. Yang","doi":"10.1109/ICEPT.2006.359831","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359831","url":null,"abstract":"Generally, the thermal profile created for the reflow furnaces contains several distinct regions, namely the initial ramp, a dwell at elevated temperature, a ramp to the maximum temperature, and a cool down region. Because of the mismatch in coefficient of thermal expansion (CTE) of the components interconnected, the thermal strain and associated thermal stress are produced during reflow, which may lead to delamination in interfacial materials and nucleating of micro crack. Reducing the maximum thermal stress has a significant improvement on the reliability of solder joints. In this paper, a finite element model of a specific BGA contained electronic assembly was built and the thermal mechanic behavior of eutectic SnPb solder joint was simulated during reflow. Further, several critical reflow profile parameters, namely the peak reflow temperature, dwell time above liquids, soak time, ramp rate, conveyor speed, were optimized in order to minimize the maximum thermal stress in the whole electronic assembly. The simulation results shows that the maximum thermal stress can be reduced by the optimization of the several critical reflow profile parameters","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"2013 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128175222","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Semiconductor Yield Analysis and Multi-Chip Package (MCP) Die Pairing Optimization using Statistical-Learning","authors":"R. Goodwin, R. Miller, E. Tuv, A. Borisov","doi":"10.1109/ICEPT.2006.359858","DOIUrl":"https://doi.org/10.1109/ICEPT.2006.359858","url":null,"abstract":"In this paper we discuss the advancement and applications of Tree based classification and regression methods to semiconductor data. We begin the paper with a description of the problem, followed by an overview of the statistical-learning techniques we use in our case studies. We then describe how the challenges presented by semiconductor data were addressed with original extensions to tree-based and kernel-based methods. Next, we review four case studies: home sales price prediction, signal identification/separation, final speed bin classification and die pairing optimization for multi-chip packages (MCP). Results from the case studies demonstrate how statistical-learning addresses the challenges presented by semiconductor manufacturing data and enables improved data discovery and prediction when compared to traditional statistical approaches","PeriodicalId":412184,"journal":{"name":"2006 7th International Conference on Electronic Packaging Technology","volume":"11 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121599525","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}