M. Gasik, M. Gasik, Klimchik Yu.V, Yu.V. Projdak, P. A, Y. Bortnikov
{"title":"Electron microscopy and x-ray spectral microanalysis of types and chemical propeties inclusions of the railway axis from a continuous billet","authors":"M. Gasik, M. Gasik, Klimchik Yu.V, Yu.V. Projdak, P. A, Y. Bortnikov","doi":"10.33101/S004-0284478","DOIUrl":"https://doi.org/10.33101/S004-0284478","url":null,"abstract":"Purpose. Analysis of status and chemical composition of non-metallic inclusions of raw railway truck axle shafts steel using electron microscopy and X-ray spectral microanalysis for the improvement of the throughout technology of the axles production.\u0000Methodology. Study of phase composition and type of non-metallic inclusions in axles shaft steel was carried out with modern equipment and method of X-ray spectral microanalysis for quantitative and qualitative data.\u0000Findings. The analysis of the elements on chemical composition on EA1N steel and of non-metallic inclusions on physical and mechanical properties of railway axles made by rolling of continuous cast billt of 470 mm diameter. The types and composition of non-metallic inclusions were studied with electron microscopy and X-ray spectral microanalysis. Results can be applied for improvement of steel refining and alloying technology for railway wheel axles production.\u0000Originality. There were discovered the original data about the types and chemical compositions of nonmetallic heterophasic inclusions in railway axis metal using the electronic microscopy and X-ray microanalysis. The obtained research results about formations of multiphase inclusions were proved using the phase equilibrium charts consiolering oxide, oxide-sulphide mineral phases. \u0000Practical value. The results of electron microscopy and X-ray spectral microanalysis are important to understand and improve the throughput technology of refining and alloying of EA1N steel for railway axle shafts.\u0000Keywords: railway axle, railway truck, axle shaft, steel chemical composition, continuous casting billet, mechanical properties, non-metallic inclusions","PeriodicalId":411963,"journal":{"name":"Metallurgicheskaya i gornorudnaya promyshlennost, №4, 2018","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116922265","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Украинскому научно-исследовательскому институту металлов – 90 лет","authors":"D. V. Stalinsky, A. S. Rudyuk","doi":"10.33101/s004-0112870","DOIUrl":"https://doi.org/10.33101/s004-0112870","url":null,"abstract":"Рассмотрены этапы становления и развития Украинского научно-исследовательского института металлов (УкрНИИМет), созданного 30 октября 1928 г. для оказания научно-технической помощи предприятиям металлургической отрасли. В течение 90 лет институт находится на передовых рубежах металлургии, совершенствуя действующие и разрабатывая новые эффективные технологии для всех металлургических переделов. В настоящее время УкрНИИМет входит в состав ГП «УкрНТЦ «Энергосталь» и, сохраняя многолетние традиции, нацелен на успешную реализацию новых проектов в области металлургического производства, энерго- и ресурсосбережения, использования вторичных энергоресурсов и защиты окружающей природной среды. Ил.3. Библиогр.: 11 назв.\u0000Ключевые слова: черная металлургия, сталь, чугун, непрерывная разливка стали, элементы верхнего строения железнодорожного пути, профили металлопроката, мелющие тела, стандартизация.","PeriodicalId":411963,"journal":{"name":"Metallurgicheskaya i gornorudnaya promyshlennost, №4, 2018","volume":"90 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126244355","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
V. Balakin, S. L. Stasevskyi, Dobriak V.D, Yu.D. Uhriumov
{"title":"Improving the preparation of the liner for rolling on the pilger mill","authors":"V. Balakin, S. L. Stasevskyi, Dobriak V.D, Yu.D. Uhriumov","doi":"10.33101/S04-38748594","DOIUrl":"https://doi.org/10.33101/S04-38748594","url":null,"abstract":"Purpose. Based on the analysis of the features of the hot piligrim pipe rolling process, develop a new and improved method for preparing liners on the mandrel by compressing their hind ends with specialized strikers of a horizontal hydraulic press.\u0000Metodology. The solution to the problem of determining the average specific application on the contact of the liner with the mandrel during compression of its rear end by specialized press dies using the method of slip lines.\u0000Findings. The article presents the results of a theoretical determination of the average specific pressure and the width of the contact surface area between the sleeve and the mandrel when the rear end of the sleeve is compressed by specialized strikers of a horizontal hydraulic press. The results obtained allow us to determine the conditions for preventing the liner from slipping from the mandrel as they move toward the rollers in the braking phase.\u0000Originality. The main factors affecting the adhesion of the liner to the mandrel were determined, and the values of average specific pressures on the contact of the metal with the mandrel were calculated during the reduction by the profile dies, as well as the width of the contact area and the required thickness of the dies. It has been established that the thickness of the strikers of a double-sided press can be assumed to be the same for all sizes of sleeves of the assortment TPA 5-12 ''.\u0000Practical value. The results of the theoretical studies can be used to modernize and reconstruct a section of the off-site charging of a pilger mill TPA 5-12 '' by installing horizontal hydraulic presses with double-die profile dies. This will increase the productivity of the mill by preventing the sleeve from sliding down the mandrel during roll-up to the rolls by creating the necessary adhesion forces between the sleeve and the mandrel. In addition, it will facilitate the conditions of the seed regime piligrim rolling, which will reduce machine time and increase productivity.\u0000\u0000Key words: pipe, liner, pilgrim mill, hydraulic press, hammer head, mandrel, performance.","PeriodicalId":411963,"journal":{"name":"Metallurgicheskaya i gornorudnaya promyshlennost, №4, 2018","volume":"17 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131533634","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Технологические способы ведения взрывных работ, позволяющие безопасно управлять действием взрыва\u0000в массиве горных пород","authors":"S. V. Tishchenko, G. I. Eremenko, D.Yu. Malykh","doi":"10.33101/s05-3958674","DOIUrl":"https://doi.org/10.33101/s05-3958674","url":null,"abstract":"Purpose. The work is devoted to improving the efficiency and safety of the escarpous blasting of rocks by borehole charges of explosives of a new design at iron ore quarries. In the thesis, the features of the process of explosive destruction of rocks by well charges of various designs are investigated. The dependences of their dynamics of explosive destruction on the physicomechanical properties of rocks are established, and the relationship between the distribution of energy of destruction in the medium and the magnitude of the specific impulse of the explosion is determined.\u0000Metodology. The obtained regularities of the impulse effect of an explosion associated with the overall energy balance imparted to a destructible medium can serve as a scale for evaluating the effectiveness of the action of well charges exploded simultaneously or through the definition of deceleration. Based on the obtained theoretical and laboratory results, a new design of a downhole charge of explosives with an air cavity in the bottom of the well has been developed.\u0000Findings. A feature of this design of the borehole charge is the concentration of the explosion energy in the bottom of the well. The optimal parameters of the air cavity and the location of the initiator relative to it in the technology of blasting have been established.\u0000Originality of the work lies in the fact that the conducted industrial tests of a new design of a borehole charge with an air cavity in the bottom part of the well showed its high efficiency.\u0000Practical value lies in achieving a reduced specific consumption of explosives. This technological process ensures uniform crushing of the blasted rock mass over the entire height of the ledge and high-quality development of the bottom of the ledge, which opens up real opportunities for the elimination of the re-drilling of the well at the inferior explosive blasting of rocks.","PeriodicalId":411963,"journal":{"name":"Metallurgicheskaya i gornorudnaya promyshlennost, №4, 2018","volume":"120 1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128488481","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}