ASME 2020 Internal Combustion Engine Division Fall Technical Conference最新文献

{"title":"Impact of Geometric Compression Ratio and Variable Valve Actuation on Gasoline Compression Ignition in a Heavy-Duty Diesel Engine","authors":"Yu Zhang, Praveen Kumar, Meng Tang, Y. Pei, Brock Merritt, M. Traver, Sriram Popuri","doi":"10.1115/icef2020-3035","DOIUrl":"https://doi.org/10.1115/icef2020-3035","url":null,"abstract":"\u0000 Gasoline compression ignition (GCI) is a promising powertrain solution to simultaneously address the increasingly stringent regulation of oxides of nitrogen (NOx) and a new focus on greenhouse gases. GCI combustion benefits from extended mixing times due to the low reactivity of gasoline, but only when held beneath the threshold of the high temperature combustion regime. The geometric compression ratio (GCR) of an engine is often chosen to balance the desire for low NOx emissions while maintaining high efficiency. This work explores the relationship between GCR, variable valve actuation (VVA) and emissions when using GCI combustion strategies. The test article was a Cummins ISX15 heavy-duty diesel engine with an unmodified production air and fuel system. The test fuel was an ethanol-free gasoline with a market-representative research octane number (RON) of 91.4–93.2. In the experimental investigation at 1375 rpm/10 bar BMEP, three engine GCRs were studied, including 15.7, 17.3, and 18.9.\u0000 Across the three GCRs, GCI exhibited a two-stage combustion process enabled through a split injection strategy. When keeping both NOx and CA50 constant, varying GCR from 15.7 to 18.9 showed only a moderate impact on engine brake thermal efficiency (BTE), while its influence on smoke was pronounced. At a lower GCR, a larger fraction of fuel could be introduced during the first injection event due to lower charge reactivity, thereby promoting partially-premixed combustion and reducing smoke. Although increasing GCR increased gross indicated thermal efficiency (ITEg), it was also found to cause higher energy losses in friction and pumping. In contrast, GCI performance showed stronger sensitivity towards EGR rate variation, suggesting that air-handling system development is critical for enabling efficient and clean low NOx GCI combustion.\u0000 To better utilize gasoline’s lower reactivity, an analysis-led variable valve actuation investigation was performed at 15.7 GCR and 1375 rpm/10 bar BMEP. The analysis was focused on using an early intake valve closing (EIVC) approach by carrying out closed-cycle, 3-D CFD combustion simulations coupled with 1-D engine cycle analysis. EIVC was shown to be an effective means to lengthen ignition delay and promote partially-premixed combustion by lowering the engine effective compression ratio (ECR). By combining EIVC with a tailored fuel injection strategy and properly developed thermal boundary conditions, simulation predicted a 2.3% improvement in ISFC and 47% soot reduction over the baseline IVC case while keeping NOx below the baseline level.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"8 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123343910","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"RCCI With High Reactivity S8-ULSD Blend and Low Reactivity N-Butanol","authors":"V. Soloiu, Cesar E. Carapia, Rick Smith, Amanda Weaver, Levi Mckinney, David Mothershed, D. Grall, M. Ilie, Mosfequr Rahman","doi":"10.1115/icef2020-3010","DOIUrl":"https://doi.org/10.1115/icef2020-3010","url":null,"abstract":"\u0000 A fuel blend consisting of 10% S8 by mass (a Fischer-Tropsch synthetic kerosene), and 90% ULSD (Ultra Low Sulfur Diesel) was investigated for their combustion characteristics and impact on emissions during RCCI (Reactivity Controlled Compression Ignition) combustion in a single cylinder experimental engine utilizing a 65% by mass n-butanol port fuel injection (PFI). RCCI is a dual fuel combustion strategy achieved with the introduction of a PFI fuel of the low-reactive n-butanol, and a direct injection (DI) of a high-reactivity blend (FT-BLEND) into an experimental diesel engine. The combustion analysis and emissions testing were conducted at 1500 RPM at an engine load of 5 bar IMEP (Indicated Mean Effective Pressure), and CA50 of 9° ATDC (After Top Dead Center); CDC (Conventional Diesel Combustion) and RCCI with 65Bu-35ULSD were utilized as the baseline for AHRR (Apparent Heat Release Rate), ringing and emissions comparisons. It was found during a preliminary investigation with a Constant Volume Combustion Chamber (CVCC) that the introduction of 10% by mass S8 into a mixture with 90% ULSD by mass only increased Derived Cetane Number (DCN) by 0.8, yet it was found to have a significant effect on the combustion characteristics of the fuel blend.\u0000 This led to the change in injection timing necessary for maintaining 65Bu-35F-T BLEND RCCI at a CA50 of 5° ATDC (After Top Dead Center) to be shifted 3° closer to TDC, thus affecting the Ringing Intensity (RI), Pressure Rise Rate, and heat release of the blend all to decrease. CDC was conducted with a primary injection of 14° BTDC at a rail pressure of 800 bar, all RCCI testing was conducted with 65% PFI of n-butanol by mass and 35% DI, to prevent knock, with a rail pressure of 600 bar and a pilot injection of 60° BTDC for 0.35 ms. 65Bu-35ULSD RCCI was conducted with a primary injection at 6° BTDC with neat ULSD#2, the fuel 65Bu-35F-T BLEND in RCCI had a primary injection at 3° BTDC to maintain CA50 at 9° ATDC. 65Bu-35ULSD RCCI experienced a NOx and soot emissions decrease of 40.8% and 91.44% respectively in comparison to CDC. The fuel 65Bu-35F-T BLEND in RCCI exhibited an additional decrease of NOx and soot of 32.9 and 5.3%, in comparison to 65Bu-35ULSD RCCI for an overall decrease in emissions of 73.7% and 96.71% respectively. Ringing Intensity followed a similar trend with reductions in RI for 65Bu-35ULSD RCCI decreasing only by 6.2% whereas 65Bu-35F-T BLEND had a decrease in RI of 76.6%. Although emissions for both RCCI fuels experienced a decrease in NOx and soot in comparison to CDC, UHC and CO did increase as a result of RCCI. CO emissions for 65Bu-35ULSD RCCI and 65Bu-35F-T BLEND where increased from CDC by a factor of 5 and 4 respectively with UHC emissions rising from CDC by a factor of 3.4. The fuel 65Bu-35F-T BLEND had a higher combustion efficiency than 65Bu-35ULSD in RCCI at 91.2% due to lower CO emissions of the blend.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"98 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122241358","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Engine Performance and Emissions for a Heavy-Duty Diesel Engine Converted to Stoichiometric Natural Gas Operation","authors":"Jinlong Liu, Christopher J. Ulishney, C. Dumitrescu","doi":"10.1115/icef2020-2964","DOIUrl":"https://doi.org/10.1115/icef2020-2964","url":null,"abstract":"\u0000 Converting existing compression ignition (CI) engines to spark ignition (SI) operation can increase the use of natural gas (NG) in heavy-duty engine applications and reduce the reliance on petroleum fuels. Gas fumigation upstream of the intake manifold and the addition of a spark plug in place of the diesel injector to initiate and control the combustion process is a convenient approach for converting existing diesel engines to dedicated NG operation. Stoichiometric operation and a three-way catalytic converter can help the engine to comply with increasingly strict emission regulations. However, as the CI-to-SI conversion usually maintains the conventional geometry of a CI engine (i.e., maintains the flat cylinder head and the bowl-in piston), the goal of this study was to observe some of the effects that the diesel conversion to stoichiometric NG SI operation will have on the engine’s performance and emissions. Dynamometer tests were performed at a constant engine speed at 1300 rpm but various spark timings. The experimental results for a net indicated mean effective pressure ∼ 6.7 bar showed that ignition timing did not affect the end of combustion due to the slow-burn inside the squish. Moreover, the less-optimal conditions inside the squish led to increased carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions. While the combustion event was stable with no signs of knocking at the medium load conditions investigated here, the results suggest that the engine control needs to optimize the mass fraction trapped inside the squish region for a higher efficiency and lower emissions.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"3 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121073081","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Quantification of Losses and Irreversibilities in a Marine Engine for Gas and Diesel Fuelled Operation Using an Exergy Analysis Approach","authors":"Beichuan Hong, Senthil Krishnan Mahendar, Jari Hyvönen, A. Cronhjort, A. Erlandsson","doi":"10.1115/icef2020-2956","DOIUrl":"https://doi.org/10.1115/icef2020-2956","url":null,"abstract":"\u0000 Large bore marine engines are a major source of fossil fuel consumption in the transport sector. The development of more efficient and cleaner marine engine systems are always required. Exergy analysis is a second-law based approach to indicate the maximum amount of work obtainable from a given system.\u0000 In this study, an exergy analysis is used to identify losses and improvement potential of a large bore Wärtsilä 31DF four-stroke marine engine system with two-stage turbocharging. An exergy-based framework is implemented on a calibrated 1D engine model to view the evolution of exergy flow over each engine sub-system while operating on different load points fuelled with natural gas and diesel separately.\u0000 The overall distributions of engine energy and exergy are initially compared at a systematic level regarding the impact of fuel mode and operating load. Furthermore, the engine irreversibilities are characterized as three types: combustion, heat dissipation, and gas exchange losses. The first type, combustion irreversibility, is the largest source of engine exergy losses amounting to at least 25% of fuel exergy. A crank resolved analysis showed that premixed gas combustion produces lower exergy losses compared to diesel diffusion combustion. The second type, thermal exergy transferred and destroyed by heat losses, are summarized for the entire engine system. From the exergy view, the charge coolers present an opportunity to recover about 9% of the brake power at full load. The last type, gas exchange losses, are categorized by accounting the flow losses caused by the valve throttling, fluid friction in pipes and the irreversibility of the two-stage turbocharging system. Most of exergy destruction in gas paths occurs at turbocharging system, where the high pressure turbocharger contributes to around 40% of the total flow exergy destruction.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130368565","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Comparing Cetane Number Measurement Methods","authors":"Riley C. Abel, J. Luecke, M. Ratcliff, B. Zigler","doi":"10.1115/icef2020-3017","DOIUrl":"https://doi.org/10.1115/icef2020-3017","url":null,"abstract":"\u0000 Cetane number is one of the most important fuel performance metrics for mixing controlled compression-ignition “diesel” engines, quantifying a fuel’s propensity for autoignition when injected into end-of-compression-type temperature and pressure conditions. The historical default and referee method on a Cooperative Fuel Research (CFR) engine configured with indirect fuel injection and variable compression ratio is cetane number (CN) rating. A subject fuel is evaluated against primary reference fuel blends, with heptamethylnonane defining a low-reactivity endpoint of CN = 15 and hexadecane defining a high-reactivity endpoint of CN = 100. While the CN scale covers the range from zero (0) to 100, typical testing is in the range of 30 to 65 CN. Alternatively, several constant-volume combustion chamber (CVCC)-based cetane rating devices have been developed to rate fuels with an equivalent derived cetane number (DCN) or indicated cetane number (ICN). These devices measure ignition delay for fuel injected into a fixed volume of high-temperature and high-pressure air to simulate end-of-compression-type conditions. In this study, a range of novel fuel compounds are evaluated across three CVCC methods: the Ignition Quality Tester (IQT), Fuel Ignition Tester (FIT), and Advanced Fuel Ignition Delay Analyzer (AFIDA). Resulting DCNs and ICNs are compared for fuels within the normal diesel fuel range of reactivity, as well as very high (∼100) and very low DCNs/ICNs (∼5). Distinct differences between results from various devices are discussed. This is important to consider because some new, high-efficiency advanced compression-ignition (CI) engine combustion strategies operate with more kinetically controlled distributed combustion as opposed to mixing controlled diffusion flames. These advanced combustion strategies may benefit from new fuel chemistries, but current rating methods of CN, DCN, and ICN may not fully describe their performance. In addition, recent evidence suggests ignition delay in modern on-road diesel engines with high-pressure common rail fuel injection systems may no longer directly correlate to traditional CN fuel ratings. Simulated end-of-compression conditions are compared for CN, DCN, and ICN and discussed in the context of modern diesel engines to provide additional insight. Results highlight the potential need for revised and/or multiple fuel test conditions to measure fuel performance for advanced CI strategies.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114299392","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Numerical Investigation of Pre-Chamber Jet Combustion in a Light-Duty Gasoline Engine","authors":"Anqi Zhang, Xin Yu, Yu Zhang, Y. Pei","doi":"10.1115/icef2020-2997","DOIUrl":"https://doi.org/10.1115/icef2020-2997","url":null,"abstract":"\u0000 Open-cycle engine simulations of a passive pre-chamber operating inside a direct-injected gasoline engine are performed and analyzed in this study. A comprehensive three-dimensional computational fluid dynamics (CFD) model has been formulated with state-of-the-art physical sub-models to account for the complex processes of engine gas exchange, fuel injection and mixing, ignition, and combustion. Numerical results are validated against experimental measurements under low load condition with high internal EGR. Realistic modeling considerations are discussed to ensure proper fidelity. In particular, the mixture conditions and flow motions could present very different features between the pre- and main chamber, which requires comprehensive simulation of the full engine cycle and imposes challenges for combustion modeling. Practically validated chemical kinetics models are essential for proper prediction of cylinder pressure history of pre-chamber jet combustion systems. Detailed analysis is then carried out to highlight key processes associated with pre-chamber operation, including residual scavenging, fuel/air mixture formation, flow pattern and turbulence development within the pre-chamber, and the ignition of main chamber mixture by issued turbulent jets. Numerical evaluation of pre-chamber design variants has been attempted, and less commonly investigated geometry parameters such as swirl nozzles and nozzle umbrella angle are found impactful for pre-chamber ignition performances.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"53 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125705430","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Combustion and Emission Characteristics of a Diesel Engine Working With Diesel/Jojoba Biodiesel/Higher Alcohol Blends","authors":"Ahmed I. El-Seesy, M. Nour, Tiemin Xuan, Zhi-xia He, H. Hassan","doi":"10.1115/icef2020-3032","DOIUrl":"https://doi.org/10.1115/icef2020-3032","url":null,"abstract":"\u0000 The main concerns of utilizing jojoba biodiesel in CI engines is that it has a high viscosity and high NOx formation. Therefore, this article purposes in endeavoring to improve the combustion and emission parameters of a CI engine working with diesel/jojoba biodiesel blend and higher alcohols under various engine loads. The higher alcohols typically are n-butanol, n-heptanol, and n-octanol, which are combined with 50% diesel, 40% of jojoba biodiesel at a volume portion of 10%, and they are designated as DJB, DJH, and DJO respectively. The jojoba biodiesel is manufactured via a transesterification process with facilitating mechanical dispersion. The findings display that there is a drop in pmax and HRR for DJB, DJH, and DJO blends compared to pure diesel fuel, whereas the combustion duration and ignition delay are extended. The brake specific fuel consumption is enlarged. Concerning engine emissions, the NOx formation is reduced while the CO, UHC, and soot emissions are increased for DJB, DJH, and DJO mixtures. It can be deduced that combining high fractions of jojoba biodiesel with C4, C7, and C8 alcohols have the feasible to accomplish low NOx formation in the interim having high thermal efficiency level.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129969101","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Predicting the Cetane Number, Yield Sooting Index, Kinematic Viscosity, and Cloud Point for Catalytically Upgraded Pyrolysis Oil Using Artificial Neural Networks","authors":"Travis Kessler, Thomas J. Schwartz, H. Wong, J. H. Mack","doi":"10.1115/icef2020-2978","DOIUrl":"https://doi.org/10.1115/icef2020-2978","url":null,"abstract":"\u0000 The conversion of biomass using fast pyrolysis has the potential to be significantly less expensive at scale compared to alternative methods such as fermentation and gasification. Selective upgrading of the products of fast pyrolysis through chemical catalysis produces compounds with lower oxygen content and lower acidity; however, identifying the specific catalytic pathways for producing viable fuels and fuel additives often requires a trial-and-error approach. Specifically, key properties of the compounds must be experimentally tested to evaluate the viability of the resultant compounds. The present work proposes predictive models constructed with artificial neural networks (ANNs) for cetane number (CN), yield sooting index (YSI), kinematic viscosity (KV), and cloud point (CP), with blind test set median absolute errors of 5.14 cetane units, 3.36 yield sooting index units, 0.07 millimeters squared per second, and 4.89 degrees Celsius, respectively. Furthermore, the cetane number, yield sooting index, kinematic viscosity, and cloud point were predicted for over three hundred expected products from the catalytic upgrading of pyrolysis oil. It was discovered that 130 of these compounds have predicted cetane numbers greater than 40, with four of these compounds possessing predicted yield sooting index values significantly less than that of diesel fuel and predicted viscosities and cloud points comparable to that of diesel fuel.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129781537","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Validation of a Directed Energy Ignition System on a Large-Bore Single Cylinder Gas-Fueled Engine","authors":"F. Pommier, David Lepley, G. Beshouri, T. Jacobs","doi":"10.1115/icef2020-2906","DOIUrl":"https://doi.org/10.1115/icef2020-2906","url":null,"abstract":"\u0000 The natural gas industry has seen a considerable increase in production recently as the world seeks out new sources of economical, reliable, and more environmentally friendly energy. Moving this natural gas requires a complex network of pipelines and compressors, including reciprocating engines, to keep the gas moving. Many of these engines were designed more than 40 years ago and must be retrofit with modern technologies to improve their performance while simultaneously reducing the harmful emissions that they produce. In this study a directed energy ignition system is tested on a two-stroke, single cylinder, natural gas-fired engine. Stability and emissions will be observed throughout a range of spark waveforms for a single speed and load that enables the most fuel-lean operation of the engine.\u0000 Improving the combustion process of the legacy pipeline engines is a substantial area of opportunity for reducing emissions output. One means of doing so is by improving an engines ability to operate at leaner conditions. To accomplish this, an ignition system needs to be able to send more energy to the spark plug in a controlled manner than a tradition capacitive-discharge ignition system. Controlling the energy is accomplished by optimizing the structure of the waveform or “profile” for each engine design. With this particular directed energy ignition system, spark profiles are able to be configured by changing the duration and amount of current sent to the spark plug. This study investigates a single operating speed and load for 9 different spark energy configurations. Engine operation at these test conditions will allow for emissions and engine performance data, using directed energy, to be analyzed in contrast to capacitive-discharge ignition.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"126 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121246980","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"The Relationship Between Steady-State Cetane Combustion Changes and Cold Start Engine Performance","authors":"Gretchen R. Simms, S. Fischer, Jay D. Cooke, L. Hamilton, D. L. Prak, J. Cowart","doi":"10.1115/icef2020-2907","DOIUrl":"https://doi.org/10.1115/icef2020-2907","url":null,"abstract":"\u0000 In the past, the Navy has investigated new renewable diesel engine fuels in comparison to conventional petroleum-based fuels using some previously published combustion metrics based on ignition delay, maximum rate of heat release and combustion phasing. These metrics quantify new fuel combustion changes using a conventional heat release analysis as compared to the base fuel. When combustion changes exceed established levels, fuel may be deemed marginal or unacceptable. In this study, these metrics are applied to Primary Reference diesel Fuel (PRF) mixtures in the range from 35 to 65. As expected, significant combustion variations are observed with lengthening ignition delay and increasing maximum heat release rate resulting from lower Cetane Number (CN) fuel. In this work, these steady-state metrics were then applied to predict the worsening of cold start engine performance. It is seen that the acceptable (‘green’) range of combustion change variations provides for acceptable cold engine starting performance. As the steady-state combustion changes become moderately more significant (‘yellow’), the cold start performance degrades. With very substantial steady-state combustion metric changes (‘red’), the cold start nature becomes unacceptable. This study shows that excellent correlation between steady-state engine performance and cold start behavior is possible.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127780182","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}