ASME 2020 Internal Combustion Engine Division Fall Technical Conference最新文献

{"title":"The Experimental Study of the Inner Insulated Turbocharger Turbine","authors":"Yang Liu, M. Madamedon, R. Burke, Jürgen Werner","doi":"10.1115/icef2020-3042","DOIUrl":"https://doi.org/10.1115/icef2020-3042","url":null,"abstract":"\u0000 For turbocharged diesel engine systems, emission reduction is the most significant challenge that manufacturers should overcome. In response to the emission reduction challenge most turbocharged diesel engine systems have adopted complex exhaust aftertreatment systems. Due to the current stringent emission regulation, exhaust aftertreatment system nowadays needs to discover new methods to increase its efficiency of pollution conversion.\u0000 Increasing the inlet temperature of aftertreatment systems can help reduce the light-off time. Whilst most methods to do this involve increases in fuel consumption (retarded injection, engine throttling), insulating the turbocharger turbine to reduce heat loss does not have this drawback.\u0000 This paper presents a simulation and experimental study the performance of a turbocharger with inner insulated turbine housing, compared with the standard turbocharger (same turbine wheel without inner insulation). Both turbochargers were tested on an engine gas stand test rig with a 2.2L prototype engine acting as an exhaust gas generator. In a steady state condition, the insulated turbocharger can achieve 5 to 14K higher turbine outlet temperature depending on the engine speed and load conditions.\u0000 Three types of transient tests were implemented to investigate turbocharger turbine heat transfer performance. The test plan was designed to the engine warm up, step load transient, WLTC cycle and simplified RDE cycle. In the engine warm up test result, the temperature drops between the turbine inlet and outlet was reduced by 4K with the insulated turbine housing. In the results of step load transient test, the turbine with insulated turbine housing was observed to get only 4K temperature benefit but with 2kRPM higher turbocharger speed under the same turbocharger inlet and outlet boundary conditions. In the WLTC cycle test result, turbocharger average speed was increased by 0.8kRPM due to the increased enthalpy of the turbine with insulation, the turbine outlet temperature has an average 1.7K improvement.\u0000 The experimental results were used to parameterise a simple, 1D, lumped capacitance model which could predict similar aerodynamic behaviour of the two turbines (turbine housing insulated and non-insulated). However, current model has less accuracy in highly transient process as the heat transfer coefficients are unchangeable in each process. The turbine outlet temperature got at most 10K error for the turbine with non-insulated housing and 13K error for the insulated one. The model was shown to over-estimate the benefits of the inner insulation for 1K in turbine outlet temperature.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"31 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122275368","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Study on Design Method of Combustion Reference Values for Model-Based Control of Advanced Diesel Engine","authors":"Jihoon Kim, Y. Yamasaki","doi":"10.1115/icef2020-3024","DOIUrl":"https://doi.org/10.1115/icef2020-3024","url":null,"abstract":"\u0000 Model-based control systems are drawing attention in relation to implementing next-generation combustion technologies with high thermal efficiency and low emissions, such as homogeneous charge compression ignition (HCCI) and premixed charge compression ignition (PCCI) combustion, which have low robustness. A model-based control system derives control inputs according to reference values and operating conditions during every cycle and has potential to replace the conventional control map, which requires a large number of experiments. However, model-based control for engines requires reference values for combustion, such as heat release peak timing and heat release peak value; such values represent the combustion state. Therefore, the reference for the transient condition is important for utilizing the benefit of model-based control systems, given that such systems derive control outputs cycle by cycle.\u0000 In this study, a design method for the combustion reference values for the transient operating condition is described for advanced diesel combustion, which uses premixed compression ignition combustion by multiple fuel injections. Specifically, a statistical method and a method based on model prediction considering the driving characteristics are proposed and compared in engine control experiments. These proposed methods were evaluated under defined simple transient operation conditions and worldwide harmonized light vehicles test cycles (WLTC) mode considering real road conditions. Results showed that designing the combustion reference values for transient operation by model prediction is effective, and such method has the potential to reflect the driving characteristics.","PeriodicalId":379034,"journal":{"name":"ASME 2020 Internal Combustion Engine Division Fall Technical Conference","volume":"5 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2020-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133083859","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}