Vegard Longva, E. Levold, H. Ilstad, S. Sævik, Frank Klæbo, Marie Finstad Opgård, Stefan Arenfeldt Vilsen
{"title":"Simulation of Trawl Board and Pipeline Pull-Over Interaction","authors":"Vegard Longva, E. Levold, H. Ilstad, S. Sævik, Frank Klæbo, Marie Finstad Opgård, Stefan Arenfeldt Vilsen","doi":"10.1115/omae2022-79928","DOIUrl":"https://doi.org/10.1115/omae2022-79928","url":null,"abstract":"\u0000 This paper presents a finite element (FE) model for simulation of trawl board and pipeline pullover interaction. The considered trawl gear system is referred to as a single otter trawl. This system consists of a single trawl net, two trawl boards and a fishing vessel which are connected by steel ropes. The trawl net was modelled by a new simplified trawl net model ensuring high computational efficiency. This trawl net model can simulate the correct tension level in the steel ropes connecting the trawl net and the trawl boards during the pipeline interaction phase, which is crucial to obtain a realistic trawl board interaction behaviour. The trawl boards were modelled as 6-DOF rigid bodies which were assigned a tailormade hydrodynamic load model based on a 3-parameter interpolation scheme both for the added mass and the forward-speed induced loads. Compared to previous work, the applied interpolation scheme was extended and improved in terms of parameter choice and number of parameters. The forward-speed induced loads consist of drag and lift loads. These loads were estimated by flume tank testing considering numerous trawl board configurations in terms of angle of attack, board-seabed inclination angle and gap between the trawl board and the seabed. Detailed measurements of the trawl board applied in the flume tank test were done to obtain an accurate description of the contact geometry, the centre of gravity and the rotational mass properties. The proposed FE model was validated against model test results of trawl board pull-over considering variation of pipeline height, pipeline diameter and trawling velocity. The FE model was found to give very good agreement with the model test in terms of build-up of pipeline interaction forces, peak force level and duration. The FE model is therefore regarded as applicable for use in design analysis of pipeline and trawl board pull-over interaction.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"204 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"134300080","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Lasse Moldestad, L. Reinås, Stian Sætre, Ø. Johnsen
{"title":"Proposal for Cyclic Riser Load Methodology Using High-Resolution Current Data","authors":"Lasse Moldestad, L. Reinås, Stian Sætre, Ø. Johnsen","doi":"10.1115/omae2022-81078","DOIUrl":"https://doi.org/10.1115/omae2022-81078","url":null,"abstract":"\u0000 Both in riser design and life extension exercises, analytical models are used to determine loads and load effects. For cyclic load assessments it is known that applied current load is an important modelling factor. In guidelines and codes for riser systems, such as DNV-RP-E104 and DNV-RP-F204, the prescribed methodology for including current in the analytical models is usually limited to scenarios with limited available statistical current data. This typically has the effect that the intended approach becomes to implement current conservatively in the analytical models, commonly applying a low current velocity. This paper presents results and findings from case studies of top tension marine drilling risers in shallow water, analyzed using 2D wave energy spectra with alternative approaches for current: high-resolution current velocity and direction data approach, and typical current loading approaches based on DNV-RP-E104. The different approaches are further investigated and supplemented by parameter sensitivity assessments. Based on the above, a methodology is proposed on how to implement current loading for cyclic load analysis when high-resolution current data is available, and the potential benefit of the improved prediction is shown. The motivation behind the proposed methodology is to provide an improved cyclic load prediction method for scenarios where high-resolution current data is available. This may be of particular interest for life extension exercises where historic cyclic riser loads can be reassessed based on historical environment and operational data.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"197 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133609409","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Vidar Hellum, Anders Vaalandsmyr, Thomas Schonlau, Anette Heimdal, Jawk Meijer
{"title":"Performance of PA6C Plastic Sheaves Used for Mooring Line Installation","authors":"Vidar Hellum, Anders Vaalandsmyr, Thomas Schonlau, Anette Heimdal, Jawk Meijer","doi":"10.1115/omae2022-79057","DOIUrl":"https://doi.org/10.1115/omae2022-79057","url":null,"abstract":"\u0000 Mooring lines are important components in floating offshore energy installations such as wind turbines and oil and gas vessels. Efficient installation of the mooring lines is important to reduce costly and energy consuming offshore operations. In the present paper investigations have been performed on the performance of sheaves made from Lamigamid® 319, which is a specific type of PA6C plastic. The sheaves are intended for subsea pull-in operations of mooring lines during mooring line installation. The sheaves are a vital component of a proposed installation system which could limit the time spent on subsea operations. Additionally, the low density of the material, the possibility of using it without bearings and using highly stressed sheaves makes it possible to reduce the necessary material for temporary equipment to a minimum. Initial Finite Element Analyses based on material models from tension tests showed that the designed sheaves would suffer large deformations when subject to the design loads. A full-scale test was performed to corroborate these results but during this test almost no permanent deformation was recorded on the sheave. Further, a test series with compression tests of different shaped samples were initiated. The first results from this test series showed a remarkable strength of the material in compression and raised several questions regarding models for predicting the behavior of Lamigamid® 319 during loading. Hence, further tests were done and modelling techniques for finding structural capacity are discussed.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"118 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116370302","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
B. Josefson, B. Chen, K. Gotoh, F. Wang, K. Liu, S. van Duin, P. Dong
{"title":"Benchmark Study of Welding Deformations in Stiffened Plate","authors":"B. Josefson, B. Chen, K. Gotoh, F. Wang, K. Liu, S. van Duin, P. Dong","doi":"10.1115/omae2022-87473","DOIUrl":"https://doi.org/10.1115/omae2022-87473","url":null,"abstract":"\u0000 The fabrication of ship hulls involves welding operations, one typical operation is fillet welding of stiffeners to plates (panels) a so-called T-joint. The residual stresses from the welding process will influence the fatigue life of the structure, and residual deformations will increase the risk for buckling of the panel and give poor fabrication tolerances which may complicate the assembly of a built-up structure.\u0000 Though this weld geometry has been frequently studied in the literature both experimentally and numerically, the focus has been on the residual stress field and if residual deformations are studied, the angular distortion and the typical V-shape seen in the welded plate (panel) are reported. This benchmark focusses on the residual shape after two-pass fillet welding of a stiffener to a plate (T-joint and the influence of the constraints used during welding. The information of the full welding residual deformations may be useful for the fabrication of larger complex welded structures.\u0000 The benchmark study clearly shows that careful consideration is needed when defining a reference plane for comparison of resulting deformations from FE-simulations and from experiments as well as good documentation of the actual boundary conditions and steps carried after the completion of the welding and before measuring residual deformations. The FE-simulations have shown that it is difficult to obtain the full antisymmetric, twisted shape of the plate as measured in the experiments, although a trend similar to the experiments can be seen as the plate tends to move upwards at the end of each weld pass, i.e a slight influence of the weld pass direction.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"41 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121701235","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Machine Learning in Fatigue Analysis for an Unbonded Flexible Riser","authors":"Jiabei Yuan, Linfa Zhu, Yucheng Hou, Z. Tan","doi":"10.1115/omae2022-83730","DOIUrl":"https://doi.org/10.1115/omae2022-83730","url":null,"abstract":"\u0000 Flexible pipelines are widely used in the offshore oil and gas projects. Comparing to steel pipes, flexible risers consist of multiple components layers, with each layer serving designated functions. For example, the helical tensile layers are used to work against axial tension from static pipe weight and amplification from the dynamic motions. As the risers are constantly experiencing stress variations due to different loadings, the fatigue performance of the tensile layers is essential to the design and operation of the flexible pipe system. Global and local fatigue analyses are usually performed in the design stage to estimate the fatigue life of tensile layers. Various parameters like vessel characteristic, pressure and temperature, environmental loadings affect the riser long-term performance. Also, multiple locations like top end fitting, bend stiffener region, touch-down zone are all potential fatigue hot-spots. To evaluate the fatigue damage at these locations, the industry standard practice is to run fatigue analysis in time domain with irregular wave. This approach is however time and resource consuming, especially when the designers have to consider thousands of load cases with long duration for numerous combinations of sea-states and operating conditions.\u0000 Baker Hughes developed a frequency domain technique for fatigue assessment on tensile layers of flexible risers. The approach builds transfer functions based on chosen time domain simulation and predict the total stress spectrum for other cases. Dirlik’s approximation method is used to estimate the fatigue damage based on the stress spectrum. Comparing to time domain approach, this approach is considerably more efficient in implementation. Since frequency domain technique simplifies the riser response as a linear system, the discrepancy must be addressed by calibration factors. To improve accuracy, more transfer functions are required to be built prior to the damage calculation.\u0000 In this paper, Baker Hughes introduces artificial neural network (ANN) technique to the developed frequency domain fatigue damage methodology. The ANN model is built between the wave spectrum and stress spectrum. Unlike the general AI technique, the type of neuron at each layer is carefully selected to represent the dynamic behavior of the riser system to improve the model efficiency. The ANN model is trained based on selected sea states. The trained model is used to predict riser damage and compared to that calculated from the time domain approach.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"43 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126128823","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Transitions in Charpy Energy and Splitting for X70 and X80 Pipe Steel","authors":"W. Mohr, T. Mcgaughy","doi":"10.1115/omae2022-78918","DOIUrl":"https://doi.org/10.1115/omae2022-78918","url":null,"abstract":"\u0000 Using data obtained for a standard production 42-inch X80 pipe with a 19.6-mm wall thickness produced around 2006 and a 24-inch diameter X70 pipe having a 0.5-inch (12.5-mm) wall thickness produced in 2016, the transition between fully brittle and fully ductile fracture behavior has been examined to assess any effects of transverse splits or delaminations. This is compared with a 48-inch X80 pipe from recent production. The 24-inch diameter pipe split more than the others, but all three showed splitting in the transition. The additional surface area formed at the splits can increase or decrease the Charpy energy by expending energy to form more fracture surface but also reducing constraint on the propagating crack as it extends through the unnotched Charpy ligament. Fitting of full Charpy energy transition curves using standard hyperbolic tangent functions does not represent the behavior well. An important transition is noted in the behavior between splitting that initiates at the initial notch tip and splitting that occurs further down in the ligament. Spitting across the notch tip increases Charpy energy by releasing constraint on crack initiation at the machined notch and occurs at temperatures just above the lower shelf temperature, where brittle fracture dominates. Splitting across the notch tip also decreases Charpy energy as compared to splitting across the ligament only. The Charpy splitting behavior also correlates to similar effects in crack tip opening displacement (CTOD) specimens for the same specimen orientation in the base material, both for conditions where unstable fracture and fully ductile response occurs.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130036370","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Kristian Norland, A. A. Larsen, Dorthe de la Cour, Henrik Ø. Larsen, T. Pedersen, M. Eriksen
{"title":"Axial In-Place Behaviour of Unbonded Flexible Pipes","authors":"Kristian Norland, A. A. Larsen, Dorthe de la Cour, Henrik Ø. Larsen, T. Pedersen, M. Eriksen","doi":"10.1115/omae2022-78959","DOIUrl":"https://doi.org/10.1115/omae2022-78959","url":null,"abstract":"\u0000 The axial behaviour of an unbonded flexible pipe is highly non-linear and may change throughout the load history and along the pipe. The axial stiffness and expansion coefficients (pressure and temperature) of a flexible pipe are given as two sets: one for the tension state and one for the compression state. Previously the typical interpretation has been that this tension/compression classification referred to the true wall axial force in the pipe. However, this approach is incomplete in several aspects:\u0000 • The determining physical factor is whether the tensile armour layers are in contact with the underlying layers.\u0000 • An unbonded flexible pipe consists of different layers with different axial force and orientation. It can be argued that the term “true wall axial force” does not make sense for an unbonded flexible pipe.\u0000 • To determine the axial force for a given condition, a set of expansion coefficients and axial stiffness must be selected. Hence, it becomes a circular argument.\u0000 Based on detailed analysis by the product supplier, a transition plane can be defined. The “Transition Plane Concept” offers an efficient way of implementing a realistic axial behaviour in the in-place design (incl. upheaval buckling). The axial behaviour during the in-place phase can be consistently defined by a transition plane and this can be implemented in the in-place analysis. Reduced risk for upheaval buckling of flexible pipes and removal of excessive conservatism can be achieved.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"18 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128772604","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The Long-Term Stress Range Distribution of Marine Risers Considering the Effect of Wave Directionality","authors":"Zohreh Sadat Haghayeghi, M. Ketabdari","doi":"10.1115/omae2022-80863","DOIUrl":"https://doi.org/10.1115/omae2022-80863","url":null,"abstract":"\u0000 The long-term distribution of stress cycles is a crucial part of the fatigue life assessment of offshore structures. This research studies the wave and current induced motion of a top tensioned riser connected to a semi-submersible platform. To account for the directionality, the platform’s directional response amplitude operator (RAO) is applied.\u0000 Since this research aims to calibrate Weibull distribution parameters, a long-term analysis of stress cycle distribution for all sea states is run. A finite element model is developed to solve riser dynamics under the effect of waves, currents, and top vessel motions. The code is solved for 87 sea states in the time domain, and then the stress cycles are derived by the Rainflow counting method. Finally, the long-term stress ranges distribution is fitted to a Weibull distribution. Comparison of the results in cases with and without directionality, shows that directional assumption leads to a broader distribution for stress ranges.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"224 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115556660","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Panagiotis Delizisis, C. Kokkinos, D. Chatzipetros, Dionisis Pettas, A. Chrysochos, K. Loukas
{"title":"Numerical Evaluation of the Thermal Performance of Modern Offshore Wind Farm Cables Installed in J-Tubes","authors":"Panagiotis Delizisis, C. Kokkinos, D. Chatzipetros, Dionisis Pettas, A. Chrysochos, K. Loukas","doi":"10.1115/omae2022-80962","DOIUrl":"https://doi.org/10.1115/omae2022-80962","url":null,"abstract":"\u0000 The submarine cables used to interconnect Offshore Wind-Farms (OWFs) with the mainland typically pass through large, metallic risers having a J-shape when approaching the Wind Turbine Generators (WTGs). These so-called “J-Tubes” consist of three main parts: water, air and platform sections. The air-section is typically sealed at both ends for practical reasons: its bottom is bounded by the water surface, while the top end by means of the armor hang-off cap. Hence, the cable may experience adverse thermal conditions within this enclosed section and the latter is likely to be the thermal bottleneck of the entire subsea route. Unfortunately, no Standardized method currently exists to calculate the current rating of cables installed in J-Tubes. This paper evaluates the applicability of the semi-empirical formulae existing in literature given the modern export cable and J-Tube designs presently used, which in many cases can give Ra numbers substantially higher than 2.3 · 106. Computational Fluid Dynamics (CFD) coupled with heat transfer analysis is employed for this purpose, while simpler heat transfer models applying the existing analytical methods are also used for comparison purposes. Furthermore, the cable is represented in a more realistic way and the convective heat transfer in the filler interior is also considered. As demonstrated in the paper, the use of analytical methods gives relatively good results for lower Ra numbers compared to the more realistic numerical models developed. However, the analytical methods may lead to very optimistic conductor temperature values when Ra becomes higher than 2.3 · 106, thus making their use rather questionable for larger J-tubes.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"17 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115710383","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The Challenges of Data Availability for the Life Extension of Steel Catenary Risers","authors":"B. Mekha, R. Gordon","doi":"10.1115/omae2022-83455","DOIUrl":"https://doi.org/10.1115/omae2022-83455","url":null,"abstract":"\u0000 Many offshore floating production systems including their risers are approaching the end of their original Design Life. Operators are faced with the choice of either decommissioning or demonstrating that the original Design Life can be extended (Life Extension). Life extension requires the Operator to perform detailed engineering analyses to verify that the system can be operated safely over the period of Life Extension. This generally requires detailed fatigue analysis of actual fabrication data to demonstrate that the fatigue damage still within the required design life and the original fabrication flaws or fatigue cracks that may have initiated over the original Design Life will not grow to a critical size resulting in failure. In some cases, the detailed engineering analysis is supplemented by an in-line inspection program.\u0000 The critical challenge that many operators face nowadays is finding the original design, fabrication and inspection records since they may be more than 20 years old. The use of actual procurement and fabrication data provides more credibility to the life extension engineering. Furthermore, the actual data could support the removal of at least some of the conservatism associated with the design of new risers.\u0000 This paper will review and discuss specific issues associated with the availability of procurement and fabrication data and how to optimize and use the available knowledge and information in cases where data is not available. Some focus will be placed on the fracture mechanics aspect of the fatigue and the Engineering Criticality Assessment (ECA) approach to determine the riser life extension based on the weld original flaws. Finally, the paper will provide guidance and examples of how to take advantage of in-line inspection to supplement the life extension analysis and provide increased confidence on the predicted life extension.","PeriodicalId":367331,"journal":{"name":"Volume 3: Materials Technology; Pipelines, Risers, and Subsea Systems","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122048357","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}