{"title":"Sidewall damage induced by FIB milling during TEM sample preparation","authors":"Qiang Gao, M. Zhang, C. Niou, Ming Li, K. Chien","doi":"10.1109/RELPHY.2004.1315415","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315415","url":null,"abstract":"A novel method was brought out to observe the physical thickness of crystal damage layer on sidewall of TEM sample. The physical thickness of the damaged layer at different accelerated voltage and beam current was given. The damage depth is about 23 and 11 nanometer at 30KeV and 10KeV ion beam, respectively. For the current, damage layer thickness keeps constant with different beam current range from 30pA to 1000pA. According to our experiment result the amorphous layer thickness keeps constant in despite of the sample tilt angle. The angle between incident beam and sample sidewall keeps fixed independent of the sample tilt. The taper of the sample will vary with different tilt angle and then the ratio between crystal and whole sample decreases with the increase of tilt angle, especially when the tilt angle exceeds 2/spl deg/.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131151275","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Analysis of leakage mechanisms and leakage pathways in intra-level Cu interconnects","authors":"V. C. Ngwan, Chunxiang Zhu, A. Krishnamoorthy","doi":"10.1109/RELPHY.2004.1315394","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315394","url":null,"abstract":"Using the carrier transport modeling in intra-level Cu interconnects, we are able to distinguish the dominant leakage mechanisms: Ohmic, Poole-Frenkel and Schottky mechanisms. In addition, the probable dominant leakage pathways: bulk-induced, barrier layer-induced or their interfaces-induced pathways are deduced to explain the leakage behavior in multilayer interconnects.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"7 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133543018","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
K. Lim, S. Jang, Yong Soo Kim, Heung-Jae Cho, Jae-Geun Oh, Su-Ock Chung, Sung-Joon Lee, Woo-Kyung Sun, J. Suh, Hong-Seon Yang, H. Sohn
{"title":"Impact of gate sidewall spacer structures on DRAM cell transistors under Fowler-Nordheim and gate-induced drain leakage stress conditions","authors":"K. Lim, S. Jang, Yong Soo Kim, Heung-Jae Cho, Jae-Geun Oh, Su-Ock Chung, Sung-Joon Lee, Woo-Kyung Sun, J. Suh, Hong-Seon Yang, H. Sohn","doi":"10.1109/RELPHY.2004.1315376","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315376","url":null,"abstract":"We studied the reliability characteristics of cell transistors with two-different type gate sidewall spacer structures (O/N vs. N/O/N) in terms of Fowler-Nordheim (F-N) or gate-induced drain leakage (GIDL) stress-immunity. Through gate oxide stress-induced leakage current (SILC), junction leakage, GIDL, and drain current-gate voltage (Id-Vg) measurement, it was observed that the GIDL stress condition had much more critical effects on the reliability of cell array transistors than the F-N stress. Particularly, it was also found that the GIDL stress-induced device degradation was severer in case of the N/O/N gate sidewall spacer than the O/N spacer. It is thought that the relatively poor reliability of the N/O/N is closely related to the trap generation near the interface of the re-oxidized SiO/sub 2//nitride at the gate bottom edge as well as the defect generation due to the sidewall nitride film stress.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"14 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114820449","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Hsiung, K. Tan, A. Komrowski, Daniel J. D. Sullivan, J. Gaudestad, A. Orozco, E. Talanova, L. A. Knauss
{"title":"Failure analysis on resistive opens with Scanning SQUID Microscopy","authors":"S. Hsiung, K. Tan, A. Komrowski, Daniel J. D. Sullivan, J. Gaudestad, A. Orozco, E. Talanova, L. A. Knauss","doi":"10.1109/RELPHY.2004.1315414","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315414","url":null,"abstract":"Scanning Super-conducting Quantum Interference Device (SQUID) Microscopy, also known as SSM, is a current density imaging technique that has been used in failure analysis to localize package- and die-level shorts. New developments have extended this technology to localizing resistive opens, augmenting other non-destructive failure analysis tools like TDR and assisting destructive deprocessing by further pin pointing defect locations. A new method to isolate resistive opens with Scanning SQUID microscopy will be presented in this paper, and demonstrated on actual resistive open yield failures in both wire-bond and flip-chip devices.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"73 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"117326279","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Detection of tin plating and tin whisker mitigation","authors":"W. Bjorndahl, L. Singleton, R. Griese, F. Chong","doi":"10.1109/RELPHY.2004.1315390","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315390","url":null,"abstract":"The problem of tin whisker growth from pure tin-plated surfaces is a well-documented phenomenon. For the space industry in particular, vacuum plasma arcing as a result of tin whisker fusing has been known to cause the failure of on-orbit satellites. The complete prevention of tin plated parts in space hardware has been a very difficult goal to achieve. Visual inspection is not reliable because tin-plated parts can be mistaken for lead-tin solder plated parts, Supplier injunctions have not worked either. First tier suppliers may provide parts in their hardware that have been plated by second, third or even fourth tier suppliers, and it is difficult to have constant awareness across all those levels. Even with injunctions, all companies providing flight hardware have had the experience of \"'discovering\" tin whiskers in their assembled hardware. Also, with the commercial markets moving to lead-free solders, the risk of pure tin making its way into hardware increases. With the shrinkage of dimensions and reductions in voltages for electronic components and packaging, tin whisker growth is becoming more of a threat. Elemental analysis using x-ray techniques have been used to successfully screen and identify tin plating. They have also been used to identify other prohibited materials such as cadmium and zinc. The difficulty in the past has been that the x-ray detector systems which were used EDX attachments to scanning electron microscopes (SEMs). These lack portability and require significant span times because of sample preparation and vacuum pump-down. Recently however, handheld portable x-ray fluorescence (XRF) analyzers have become available which offer accurate analyses. The purpose of this poster session is not to describe or redescribe the tin whisker phenomenon. This is well described the literature. Rather, we describe the processes that we used in removing tin-plated parts from our inventories. There were three different parts to the process. First, we prioritized the part commodity types according to their likelihood of containing pure tin plating. Then, the prioritized inventory was evaluated using portable XRF detectors and where this was not possible using EDX analysis in a SEM system. Then, with tin plated lots that we knew had found their way into flight hardware, we followed a disposition process similar to that described by McDowell [2].","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124635940","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Effects of hot-carrier stress on the performance of CMOS Low Noise Amplifier","authors":"S. Naseh, M. Deen","doi":"10.1109/RELPHY.2004.1315363","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315363","url":null,"abstract":"The effects of DC hot-carrier stress on the performance of a CMOS Low Noise Amplifier (LNA) are investigated. It was observed that the main effects caused by stress on the NMOSFETs in the LNA are a decrease of the transconductance g/sub m/ and an increase of the output conductance g/sub ds/. As a result of these changes, the power gain of the amplifier S/sub 21/, input matching S/sub 11/ and output matching S/sub 22/ are deteriorated. The linearity of the LNA improved after stress and this is believed to be due to the improvement in the linearity of the I-V characteristics of the transistors in the circuit at the particular biasing points the measurements were made. The noise figure of the circuit also increases after hot carrier stress which is believed to be due to increase in channel thermal noise caused by hot carriers.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"61 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124682284","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
J. Fiorenza, G. Braithwaite, C. Leitz, M. Currie, Z. Cheng, V. Yang, T. Langdo, J. Carlin, M. Somerville, Anthony Lochtefeld, H. Badawi, M. Bulsara
{"title":"Investigation of misfit dislocation leakage in supercritical strained silicon MOSFETs","authors":"J. Fiorenza, G. Braithwaite, C. Leitz, M. Currie, Z. Cheng, V. Yang, T. Langdo, J. Carlin, M. Somerville, Anthony Lochtefeld, H. Badawi, M. Bulsara","doi":"10.1109/RELPHY.2004.1315378","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315378","url":null,"abstract":"This paper investigates off-state current leakage in strained silicon NMOSFETs built on supercritical thickness strained silicon films. it describes a simple conceptual model for the off-state leakage: the leakage is caused by enhanced dopant diffusion near misfit dislocations. This paper studies the validity of this hypothesis using both DC IV measurements and photon emission microscopy measurements of NMOSFETs with several different supercritical strained silicon thickness values. It shows that the emission measurements of the off-state leakage and the gate length dependence of the off-state leakage can both be easily explained by the leakage model. It also demonstrates that the response to an applied gate or back-bias voltage of the IV characteristics and the light emission data can be understood within the context of the proposed conceptual model.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"6 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130170806","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Layout design dependence of NBTI for I/O p-MOSFET","authors":"V. Kol'dyaev","doi":"10.1109/RELPHY.2004.1315440","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315440","url":null,"abstract":"Every VLSI product has some distributions of I/O p-MOSFET design with respect to the channel lengths and widths. For reliability evaluation the most vulnerable design is to be chosen. To do this there is a need to investigate a layout dependence of NBTI for I/O pMOSFET being the most weak among all others types of logic transistors. The study has resulted in the right choice of the transistors for NBTI routing testing, process optimization to improve the NBTI and to find the right spec for the product qualification.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129088551","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Development and use of a miniaturized health monitoring device","authors":"V. Rouet, B. Foucher","doi":"10.1109/RELPHY.2004.1315431","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315431","url":null,"abstract":"A Time Stress Measurement Device is an electronic instrument that records environmental or factual measurements (temperature, relative humidity, shocks, vibrations, on/off, open/closed, voltage, pressure, ...). All these measurements are then dated and stored. Typically, a TSMD is a battery-powered device that is equipped with a microcontroller (for electronic management), memory (for data storage) and sensors (for recordings of environmental data). Most TSMDs use turnkey software on a personal computer to set up and initiate the TSMD as well as retrieve and compute the collected data. TSMD technology is based on embedded or remote environmental stress sensors linked to a microcontroller that controls the sensors (e.g. threshold values), the inputs from the sensors (e.g. sampling frequencies) and the memories (e.g. number and type of recordings). A TSMD provides information for enhanced failure analysis, particularly intermittent failures, and permits trend analysis for preventive maintenance. The aim of using such a device is to determine the impact the environment has on a particular system of interest. The TSMD allows a complete recording of environmental data over time. The scope of the CLIO project is to generalise the TSMD concept, The aim is to develop an autonomous, miniaturised and multi-application TSMD that could be used in civil and military domains.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130556414","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
A. Itri, D. Ielmini, A.L. Lacaitat, A. Pirovano, E. Pellizzer, R. Bez
{"title":"Analysis of phase-transformation dynamics and estimation of amorphous-chalcogenide fraction in phase-change memories","authors":"A. Itri, D. Ielmini, A.L. Lacaitat, A. Pirovano, E. Pellizzer, R. Bez","doi":"10.1109/RELPHY.2004.1315325","DOIUrl":"https://doi.org/10.1109/RELPHY.2004.1315325","url":null,"abstract":"We investigated the current-induced phase transformations in chalcogenide-based memories. By electrical characterization and compact simulation of the memory I - V, we point out the evidence for a stacked distribution of phases as a result of the applied programming pulses. An anomalous cell behavior is also shown, which we explain in terms of parallel phase transition in the cell. A new technique for estimating the amorphous fraction is proposed, requiring only a simple manipulation of I - V characteristics of the memory.","PeriodicalId":319841,"journal":{"name":"2004 IEEE International Reliability Physics Symposium. Proceedings","volume":"63 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2004-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121095343","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}