{"title":"Pulse width modulated buck-boost five-level current source inverters","authors":"F. Gao, P. Loh, F. Blaabjerg, D. Vilathgamuwa","doi":"10.1109/APEC.2008.4522763","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522763","url":null,"abstract":"This paper presents new five-level current source inverters (CSIs) with voltage/current buck-boost capability. Being different from the existing multilevel CSI, the proposed CSIs were first designed to regulate the flowing path of dc input current by controlling two additional active switches, resulting in the natural balance of input current. For maintaining the normalized volt-sec average unchanged, the alternative phase opposition disposition (APOD) modulation scheme with typical gating signal mapping technique from voltage source inverter (VSI) to CSI can be assumed to control the five-level buck-boost CSIs. Next by observing the hidden current charging path during inductive charging interval under APOD modulation, it is noted that the buck-boost five-level CSI can then be further modified with lesser active component without degrading output performance. To verify the theoretical findings, Matlab simulations with PSIM coupler were performed before constructed laboratory prototypes were tested, whose captured results are presented for visual confirmation.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130752159","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A reconfigurable solar photovoltaic array under shadow conditions","authors":"D. Nguyen, Bradley Lehman","doi":"10.1109/APEC.2008.4522840","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522840","url":null,"abstract":"This paper proposes an adaptive reconfiguration scheme to reduce the effect of shadows on solar panels. A switching matrix connects a solar adaptive bank to a fixed part of a solar PV array, according to a model based control algorithm that increases the power output of the solar PV array. Control algorithms are implemented in real-time. An experimental reconfiguration PV system with the battery load is presented and is shown to verify the proposed reconfigurations.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131004154","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"An electrical circuit based 3-D thermal model of a fan cooled 600μH, 80A inductor for a plasma cutting power supply","authors":"G. Kamath","doi":"10.1109/APEC.2008.4522753","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522753","url":null,"abstract":"This paper applies a 3-D electrical circuit based thermal model technique described in [1] to analyze the thermal performance of a 600 muH, 80 A inductor for a plasma cutting application. The forced convective heat transfer terms in the model are derived using the empirical correlation method [2, 3]. This approach is cost-effective since it does not use an FEA tool for the analysis. Also, the circuit based nature of the model facilitates seamless coupling of the magnetic and thermal physics that affect the inductor in a standard circuit simulator environment. A comparative evaluation of the simulation results with experiment shows that the average coil temperature error is in the 10-12% range while the average layer temperature error is in the 3-16% range. This is lower than that seen in [1] where errors in the range 25-40% are recorded. However, the model has limitations due to the presence of individual winding layer temperature errors in the range 18-50%. Factors affecting the performance of the model are also discussed in the paper.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131197943","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Multiple-Phase high-accuracy hysteretic current-mode voltage regulator for powering microprocessors","authors":"Chunping Song, J. Nilles","doi":"10.1109/APEC.2008.4522770","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522770","url":null,"abstract":"In this paper, the accuracy of multiple-phase hysteretic current-mode voltage regulators for powering microprocessors is thoroughly analyzed. The inaccuracy issue is pointed out and the root causes is identified. Then to improve the DC regulation accuracy, a new high-accuracy multiple-phase hysteretic current-mode regulator is proposed in the paper based on the accuracy analysis. Finally the experimental results show the effectiveness of this accuracy analysis and this new proposed high-accuracy multiple-phase hysteretic current- mode regulator for powering microprocessors.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"17 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132291260","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Interleaved flyback converter with turn-on/off snubber for poultry stunning applications","authors":"S. Tseng, C.-T. Hsieh, C.-M. Yang","doi":"10.1109/APEC.2008.4523002","DOIUrl":"https://doi.org/10.1109/APEC.2008.4523002","url":null,"abstract":"This paper proposes an interleaved flyback converter with a novel L-C-D snubber to reduce turn-on and turn-off losses. The proposed L-C-D snubber is composed of a single capacitor to form turn-off snubber, and an inductor and a diode connected in parallel to form turn-on snubber. In this circuit structure, the turn-off snubber is used to limit rising rate of drain-source voltage of MOSFET and to reduce turn-off switching loss. While, the turn-on ones are used to smooth out current passing switch and to reduce turn-on switching loss. In addition, the proposed converter is operated in an interleaved fashion to reduce output current ripple. Compared with the counterparts of conventional converter topologies, the proposed converter has the merits of less component counts, higher efficiency, small size, and they are easier to implement. Measured results obtained from a prototype flyback converter have verified the feasibility.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"141 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132688077","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A 10KV shunt hybrid active filter for a power distribution system","authors":"Wu Jian, He Na, Dianguo Xu","doi":"10.1109/APEC.2008.4522832","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522832","url":null,"abstract":"This paper analyzes the compensation performance of a shunt hybrid active power filter. The hybrid active power filter, which combines passive filter and active power filter, has both respective merits, and is an important developing trend of filtering device. The hybrid active power filter can reduce the capacity of active power filter effectively and is more suitable for the engineering application for high voltage nonlinear loads. The compensation performance of hybrid active power filter is analyzed by estimating the effect of different active power filter gain and parameters change. Then, a conclusion has been obtained that the harmonic attenuation rate is insensitive to the variation of passive parameters when the active power filter with an enough feedback gain is combined. Finally, the feasibility and validity of proposed scheme is verified by simulation using Matlab and a hybrid shunt active power filter prototype.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123526322","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Xinping Ding, Z. Qian, Shuitao Yang, Fang-zen Peng
{"title":"A new feedforward compensation to reject Dc-link voltage ripple in bi-directional Z-Source inverter ASD system","authors":"Xinping Ding, Z. Qian, Shuitao Yang, Fang-zen Peng","doi":"10.1109/APEC.2008.4522972","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522972","url":null,"abstract":"A feedforward compensator applied in Z-source inverter ASD system has been presented. With this technique a constant peak dc-link voltage can be achieved with an excellent transient performance which enhances the rejection of input voltage ripple, and have good ride- through for voltage-sags. The effect of six pulse input voltage ripple which result from front-end diode rectifier has been described in detail, and the compensator is designed. The Z-source inverter ASD system with feedforward compensator has rapid transient response and good ride-through for voltage sag. It is very suitable for practical application due to its simplified controller design. The proposed technique was verified on a 10-kW prototype. The experimental and simulation results verified the theory very well.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"183 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121937456","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Current sensorless control for single-phase boost-type SMR","authors":"Hung-Chi Chen, Chih-Kai Huang","doi":"10.1109/APEC.2008.4522878","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522878","url":null,"abstract":"In this paper, the single-loop current sensorless controls (SLCSC) for single-phase boost-type switching-mode- rectifiers (SMRs) are developed and digitally implemented in DSP-based system. Compared to the conventional multi-loop control with one inner current loop and one outer voltage loop, there is only one voltage loop in the proposed SLCSCs where its output is used to shift the nominal duty ratio pattern generated from the sensed input and output voltage. Because of no current loop, the efforts of sampling and tracking inductor current are unnecessary. It implies that the proposed SLCSCs are simple and very adaptable to the implementation with mixed-signal integrated circuits. It is also noted that the proposed SLCSCs are operated at continuous-current-mode (CCM). In this paper, first, the effects of shifting nominal duty ratio pattern on the input current waveform are analyzed and modeled with considering the inductor resistance and conduction voltages. It shows that the aligned current waveform can be inherently generated by the nominal duty ratio pattern and the current amplitude is roughly proportional to the shifting phase of nominal duty ratio pattern. Then, a voltage controller is included to regulate the dc output voltage by tuning this controllable phase. Finally, some simulated and experimental results have been given to demonstrate the performances of the proposed SLCSCs.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124473031","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"PWM inverter output filter cost to losses trade off and optimal design","authors":"R. Pasterczyk, J. Guichon, J. Schanen, E. Atienza","doi":"10.1109/APEC.2008.4522764","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522764","url":null,"abstract":"This paper describes how to design the output filter of a PWM inverter used in a Uninterruptible Power Supply. Several constraints apply to this design: physical limitations of all material and components, output waveform quality, losses, cost, ... All models used in the design process are described: semiconductor, inductor and capacitor losses, cost, Total Harmonic Distortion (THD), short circuit behavior... Input parameters are control law, switching frequency, inductor design parameters (number of turns and magnetic circuit) and capacitor values. Based on these design models, optimization is carried out, and cost-losses trade-off curves are deduced. Two power levels (30 kVA and 300 kVA) are taken as design example, with the same models, in order to show the robustness of the method.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"29 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129426337","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Mariéthoz, A. Beccuti, G. Papafotiou, M. Morari
{"title":"Sensorless explicit model predictive control of the DC-DC buck converter with inductor current limitation","authors":"S. Mariéthoz, A. Beccuti, G. Papafotiou, M. Morari","doi":"10.1109/APEC.2008.4522957","DOIUrl":"https://doi.org/10.1109/APEC.2008.4522957","url":null,"abstract":"This paper investigates the digital control of DC- DC buck converters. It proposes a new explicit model predictive controller for a buck DC-DC converter. The controller features an inherent current limitation over a wide range of loads and supply voltages using no current sensor. It achieves good reference tracking and good rejection of line and load transients. The complexity of the controller is limited as it consists of a table of optimal state feedback gains that have been derived off-line and that are chosen according to the measured state. Feasibility is validated experimentally on a fixed point DSP.","PeriodicalId":219425,"journal":{"name":"2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition","volume":"7 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2008-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128668608","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}