{"title":"Development of a Rayleigh Scattering Diagnostic for Time-Resolved Gas Flow Velocity, Temperature, and Density Measurements in Aerodynamic Test Facilities","authors":"A. Mielke, K. A. Elam, C. Sung","doi":"10.1109/ICIASF.2007.4380892","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380892","url":null,"abstract":"A molecular Rayleigh scattering technique is developed to measure time-resolved gas velocity, temperature, and density in unseeded turbulent flows at sampling rates up to 32 kHz. A high power continuous-wave laser beam is focused at a point in an air flow field and Rayleigh scattered light is collected and flber-optically transmitted to the spectral analysis and detection equipment. The spectrum of the light, which contains information about the temperature and velocity of the flow, is analyzed using a Fabry-Perot interferometer. Photomultiplier tubes operated in the photon counting mode allow high frequency sampling of the circular interference pattern to provide time-resolved flow property measurements. An acoustically driven nozzle flow is studied to validate velocity fluctuation measurements, and an asymmetric oscillating counterflow with unequal enthalpies is studied to validate the measurement of temperature fluctuations. Velocity fluctuations are compared with constant temperature anemometry measurements and temperature fluctuations are compared with constant current anemometry measurements at the same locations. Time-series and power spectra of the temperature and velocity measurements are presented. A numerical simulation of the light scattering and detection process was developed and compared with experimental data for future use as an experiment design tool.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"15 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121068189","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
C. Klein, U. Henne, W. Sachs, R. Engler, Y. Egami, V. Ondrus, U. Beifuss, H. Mai
{"title":"Application of Pressure-Sensitive Paint for Determination of Dynamic Surface Pressures on a Rotating 65° Delta Wing and an Oscillating 2D profile in Transonic Flow","authors":"C. Klein, U. Henne, W. Sachs, R. Engler, Y. Egami, V. Ondrus, U. Beifuss, H. Mai","doi":"10.1109/ICIASF.2007.4380887","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380887","url":null,"abstract":"Visualization and measurements of aerodynamic effects on a delta-wing model and a 2D-wing-profile model were conducted using an optical pressure measurement system, based on the pressure-sensitive paint (PSP) technique. The PSP technique can be used to obtain absolute pressure measurements on the surface of a model and in addition to evaluate quantitative aerodynamic flow phenomena by using scientific grade cameras and image processing techniques. The PSP technique has been used here for investigations of periodic and unsteady flows: first, a 65deg delta wing was tested in the transonic wind tunnel DNW-TWG in Gottingen. A specially designed roll apparatus enabled roll rates up to 10 Hz. The experiments were carried out at angles-of-attack up to alpha = 17deg at Ma = 0.8. Since the rotation of the delta wing is a periodic motion, the phase-locked unsteady PSP technique can be applied. In a second wind tunnel campaign in the DNW-TWG in collaboration with the DLR Institute of Aeroelasticity, a 2D-wing-profile model, which is pitch oscillating at up to 30 Hz, was investigated. The experiments were performed at angles-of-attack alpha = 1.12deg plusmn 0.6deg at Ma = 0.72. For these experiments pressure measurements were carried out in one wind tunnel entry by means of both phase-locked unsteady as well as unsteady PSP techniques.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"47 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124886153","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Virtual Diagnostics Interface: Real Time Comparison of Experimental Data and CFD Predictions for a NASA Ares I-Like Vehicle","authors":"R.J. Schwartz, G.A. Fleming","doi":"10.1109/ICIASF.2007.4380901","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380901","url":null,"abstract":"Virtual diagnostics interface technology, or ViDI, is a suite of techniques utilizing image processing, data handling and three-dimensional computer graphics. These techniques aid in the design, implementation, and analysis of complex aerospace experiments. LiveView3D is a software application component of ViDI used to display experimental wind tunnel data in real-time within an interactive, three-dimensional virtual environment. The LiveView3D software application was under development at NASA Langley research center (LaRC) for nearly three years. LiveView3D recently was upgraded to perform real-time (as well as post-test) comparisons of experimental data with pre-computed computational fluid dynamics (CFD) predictions. This capability was utilized to compare experimental measurements with CFD predictions of the surface pressure distribution of the NASA Ares I crew launch vehicle (CLV) -like vehicle when tested in the NASA LaRC unitary plan wind tunnel (UPWT) in December 2006 - January 2007 timeframe. The wind tunnel tests were conducted to develop a database of experimentally-measured aerodynamic performance of the CLV-like configuration for validation of CFD predictive codes.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"2007 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128215492","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Conceptual Design of a Laser Light Sheet Flow Visualization System for a Pressurized, Low Speed Wind Tunnel","authors":"K. Mejia, C. Jorgens","doi":"10.1109/ICIASF.2007.4380896","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380896","url":null,"abstract":"The conceptual design and component validation of a laser light sheet flow visualization system for the QinetiQ 5m wind tunnel was conducted over the last two years by the Testing Methods Group of Boeing Commercial Airplanes. The purpose of this system is to complement wind tunnel force and pressure data by helping visualize off-body aerodynamic phenomena affecting model performance to help diagnose discrepancies between experimental and computational results. Smoke seeding and laser diagnostics are commonplace in many wind tunnels around the world. However, the requirement that this system be robust and user friendly enough to operate quickly and reliably in a high Reynolds number, large scale, low speed wind tunnel environment make this a unique and complex system. Each of the 4 major system components (laser, optics, seeding, and dispensing) were researched in detail and candidate system components were identified. In addition, two wind tunnel tests were conducted in a smaller, open circuit low speed wind tunnel to validate some of the findings and to prototype candidate hardware.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"27 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126374237","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Evaluation of Lifetime-based Pressure-Sensitive Paint Measurement in Low-speed Flow","authors":"T. Yamashita, H. Nagai, K. Asai","doi":"10.1109/ICIASF.2007.4380884","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380884","url":null,"abstract":"The lifetime-based method has been applied to pressure-sensitive paint (PSP) measurement in low-speed flow. Based on theoretical considerations and sample tests, a method to calculate pressure using \"a-priori\" method was proposed. In this method, pressure is related to the ratio of the luminescent intensity ratios obtained at two different gates between the wind-on and wind-off conditions, multiplied by a temperature correction factor calculated from the single-point measurement of model substrate temperature. The sample tests showed that the effect of temperature as well as non-uniformity of lifetime could be cancelled out by the proposed method. In order to evaluate the effectiveness of this method, a simplified car model was tested in a low-speed wind tunnel. The result obtained by the lifetime method was in good agreement with those of pressure taps and the intensity method.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123493050","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Velocity Measurements Near Walls, Cavities, and Model Surfaces Using Particle Shadow Velocimetry (PSV)","authors":"L. Goss, J. Estevadeordal, J. Crafton","doi":"10.1109/ICIASF.2007.4380874","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380874","url":null,"abstract":"The Particle Shadow Velocimetry (PSV) technique is utilized for velocity measurements near walls, in cavities, and near model surfaces. Measurements are made on a readward facing step, a cylinder in cross flow and in an open water cavity. Velocity information obtained by two different analysis approaches, traditional grid based and particle centric cross-correlations, are compared. It is shown that the particle centric methods yields more details in complex flows. This paper shows that the PSV technique is well suited for measurements near surfaces where conventional laser-based PIV methods are hampered by surface glare and/or optical access.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"16 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123510305","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Fonov, J. Crafton, L. Goss, G. E. Jones, B. Schulze
{"title":"Investigation of Pressure and Friction Force Distributions on a Model Tail Wing Using Pressure Sensitive Paint and Surface Stress Sensitive Film","authors":"S. Fonov, J. Crafton, L. Goss, G. E. Jones, B. Schulze","doi":"10.1109/ICIASF.2007.4380889","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380889","url":null,"abstract":"This paper describes measurement methodology and comparative results obtained using both the Pressure Sensitive Paint (PSP) and novel Surface Stress Sensitive Film (S3F) techniques. A wind tunnel test was performed by EADS together with ISSI to investigate PSP at low speeds in order to compare absolute PSP pressures and S3F relative pressure data on a typical high speed aircraft model. Furthermore the ability of the S3F film to sense wall shear stresses was demonstrated. Measurements were conducted in the flow range of 10-50 m/s, angles of attack of 10deg and 30deg and with two model configurations (with and without an air brake).","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"5 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124726849","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Determination of Velocity and Skin Friction Fields from Images by Solving Projected Motion Equations","authors":"Tianshu Liu, Lixin Shen","doi":"10.1109/ICIASF.2007.4380878","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380878","url":null,"abstract":"This paper describes a general method to extract velocity and skin friction fields from images based on the projected motion equations. The generic form of the projected motion equations and the optical flow equation are given for typical flow visualizations, where the optical flow is proportional to the path-averaged velocity of fluid or particles weighted with a specific field quantity like dye concentration, fluid density and particle density. The variational formulation with a smoothness constraint is used to calculate the optical flow in the image plane that is proportional to the path-averaged velocity. This method allows determination of velocity fields from various visualization images of complex flows from large atmospheric storms to supersonic mixing layers. Similarly, the projected motion equation for oil doped with luminescent molecules is derived under an assumption that the luminescent intensity is proportional to the oil thickness when the oil film is optically thin. The equation is solved using the variational method to extract a skin friction field from images of the evolution of the luminescent oil film in flows. Examples are given to illustrate applications of the proposed method.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"12 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121211671","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Filtered Rayleigh Scattering-Based Concentration Measurements for a Horizontal Buoyant Jet","authors":"C. McGaha, M. Reeder","doi":"10.1109/ICIASF.2007.4380890","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380890","url":null,"abstract":"Filtered Rayleigh scattering (FRS) is a non-intrusive technique which is used to study a variety of flowfields. It utilizes a narrow linewidth laser, an absorption filter, and a detector. The laser illuminates the flow field and molecular scattering provides the signal to the camera. The difference in molecular cross section can be used to discriminate between unmixed gaseous components. The focus of this research is to document the behavior of a horizontal buoyant jet of gaseous helium using FRS. Despite its simplicity, the behavior of the near field of horizontal buoyant jets is sparsely described in the literature compared to vertical buoyant jets. Gross features, such as jet core trajectory and gross mixing rate are generally characterized using Reynolds number (Re) and Grashof number (Gr), and are presented herein as well. The FRS system for this research consists of a continuous coherent argon Sabre R series ion laser, an iodine absorption filter, and a PCO.4000 camera. A helium jet of precisely controlled mass flow rate is flows through a tube into the surrounding ambient laboratory with a very low velocity co-flow of particle free air. The behavior of jets with Reynolds numbers under 1000 are described in this report. Our results of our study show a clear expulsion of core fluid in the form of side jets, consistent with helical mode excitation. The pattern of core fluid expulsion is striking and apparently is Reynolds number dependent. Additionally, the trajectory and mixing characteristics of the buoyant jet were analyzed as a function of downstream distance. A significant portion of this study is dedicated to measuring the rate at which FRS data can be acquired with a continuous wave laser. Exposure times as small as 0.01 seconds provided some data, though most of the analysis was performed for longer time exposures to improve the signal to noise ratio.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"283 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116091021","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Clean Seeding for Particle Image Velocimetry","authors":"C. McNiel, D. Peltier, M. Reeder, J. Crafton","doi":"10.1109/ICIASF.2007.4380880","DOIUrl":"https://doi.org/10.1109/ICIASF.2007.4380880","url":null,"abstract":"Particle Image Velocimetry (PIV) is a flow velocity measurement technique in which small seed particles are inserted into a flow and tracked through photography. Traditional PIV techniques utilize solid or liquid seed particles that can persist in closed circuit wind tunnels and corrode or damage components of the tunnel or model. Solid carbon dioxide (CO2) is an alternative seed material that neither persists in closed loop wind tunnels nor damages any tunnel components. This research effort demonstrates the viability of CO2 as a PIV seed material in a supersonic blow down tunnel. Experiments were conducted with an empty test section, a cavity flow and a cone model present in the test section. For the empty test section, the results compare to within 4% of the velocity predicted by one dimensional isentropic flow models. In addition, experiments were conducted for a cavity flow regime and for flow around a cone model. These additional experiments all qualitatively demonstrated expected flow characteristics.","PeriodicalId":195072,"journal":{"name":"2007 22nd International Congress on Instrumentation in Aerospace Simulation Facilities","volume":"6 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-06-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126148756","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}