Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles最新文献

{"title":"Enhancing surfactant desorption through low salinity water post-flush during Enhanced Oil Recovery","authors":"I. Ngo, K. Sasaki, Li-qiang Ma, R. Nguele, Y. Sugai","doi":"10.2516/OGST/2021050","DOIUrl":"https://doi.org/10.2516/OGST/2021050","url":null,"abstract":"Low Salinity Water (LSW) incorporates in surfactant Enhanced Oil Recovery (EOR) as a pre-flush is a common practice aiming to reduce the formation salinity, which affects surfactant adsorption. However, in a field implementation, the adsorption of surfactant is unavoidable, so creating a scheme that detaches the trapped surfactant is equally essential. In this study, LSW was a candidate to enhance the desorption of surfactant. LSW solely formulated from NaCl (1 wt.%), Sodium Dodecylbenzene Sulfonate (SDBS) was chosen as the primary surfactant at its critical micelle concentration (CMC, 0.1 wt.%). It found that injecting LSW as post-flush achieved up to 71.7% of SDBS desorption that lower interfacial tension against oil (31.06° API) to 1.3 mN/m hence bring the total Recovery Factor (RF) to 56.1%. It was 4.9% higher than when LSW injecting as pre-flush and 5.2% greater than conventional surfactant flooding (without LSW). Chemical analysis unveiled salinity reduction induces Na+ ion adsorption substitution onto pore surface resulting in an increment in surfactant desorption. The study was further conducted in a numerical simulation upon history matched with core-flood data reported previously. By introducing LSW in post-flush after SDBS injection, up to 5.6% RF increased in comparison to other schemes. The proposed scheme resolved the problems of adsorbed surfactant after EOR, and further improve the economic viability of surfactant EOR.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"104 1 1","pages":"68"},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"85654358","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Crude oil price prediction using CEEMDAN and LSTM-attention with news sentiment index","authors":"Zhenda Hu","doi":"10.2516/OGST/2021010","DOIUrl":"https://doi.org/10.2516/OGST/2021010","url":null,"abstract":"Crude oil is one of the most powerful types of energy and the fluctuation of its price influences the global economy. Therefore, building a scientific model to accurately predict the price of crude oil is significant for investors, governments and researchers. However, the nonlinearity and nonstationarity of crude oil prices make it a challenging task for forecasting time series accurately. To handle the issue, this paper proposed a novel forecasting approach for crude oil prices that combines Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN), Long Short-Term Memory (LSTM) with attention mechanism and addition, following the well-known “decomposition and ensemble” framework. In addition, a news sentiment index based on Chinese crude oil news texts was constructed and added to the prediction of crude oil prices. And we made full use of attention mechanism to better integrate price series and sentiment series according to the characteristics of each component. To validate the performance of the proposed CEEMDAN-LSTM_att-ADD, we selected the Mean Absolute Percent Error (MAPE), the Root Mean Squared Error (RMSE) and the Diebold-Mariano (DM) statistic as evaluation criterias. Abundant experiments were conducted on West Texas Intermediate (WTI) spot crude oil prices. The proposed approach outperformed several state-of-the-art methods for forecasting crude oil prices, which proved the effectiveness of the CEEMDAN-LSTM_att-ADD with the news sentiment index.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"31 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75796430","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"The influence of residual stress for the strength of plate-fin structures in the typical operation process of Liquefied Natural Gas (LNG) heat exchanger","authors":"Hongqiang Ma, Jiwei Jia, Xinmei Luo, Li Wang, Caiqin Hou, Gang Wang, Yujin Zhang","doi":"10.2516/ogst/2021063","DOIUrl":"https://doi.org/10.2516/ogst/2021063","url":null,"abstract":"In order to ensure the safe operation of heat exchangers in the Liquefied Natural Gas (LNG), the stress analysis model of aluminum Plate-Fin Structure (PFS) is established based on the thermal-elastic-plasticity theory. The residual stress distribution of PFS and its influence on the structural strength is analyzed by the thermal-structural coupling method. The results indicate that the residual stress distribution of PFS is very complex, and the residual stress reaches the peak at the Brazed Joint (BJ). Due to the equivalent stress at BJ near the fin is higher than that at BJ near the plate, cracks are more easily produced at BJ near the fin. Therefore, the existence of residual stress has a negative impact on PFS, which may increase the possibility of strength failure at BJ under the typical operating conditions (normal operation, cut-down and heat-up) of the heat exchanger. In addition, the residual stress gradually decreases with the brazing cooling rate decrease. The residual stress within the PFS will be effectively reduced by properly reducing the brazing cooling rate, which can slow down the strength failure of the PFS. The above research results will provide an important basis for the design and safe operation of the aluminum plate-fin heat exchanger.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"43 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75472472","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Nitrogen compounds removal from oil-derived middle distillates by MIL-101(Cr) and its impact on ULSD production by hydrotreating","authors":"E. Meneses-Ruiz, J. Escobar, Rodolfo Juventino Mora, J. A. Montoya, María Concepción Barrera, D. Solís-Casados, L. Escobar-Alarcón, P. Angel, G. Laredo","doi":"10.2516/OGST/2021038","DOIUrl":"https://doi.org/10.2516/OGST/2021038","url":null,"abstract":"Oil-derived middle distillates (straight-run gas oil and mixture with light cycle oil and coker gas oil) for Ultra-Low Sulfur Diesel (ULSD) production by HyDroTreating (HDT) were pretreated by selective Nitrogen Organic Compounds (NOC) adsorption. Highly crystalline Metal-Organic Framework (MOF) MIL-101(Cr) prepared with propylene oxide (proton scavenger) as textural improver was used to that end. MOF was characterized by N2 physisorption, X-ray diffraction, thermal analysis, infrared, Raman and UV-vis spectroscopies, and electron microscopy (SEM and HR-TEM). NOC removal was carried out at room temperature and atmospheric pressure, the adsorbent being easily regenerable under mild conditions. Extruded MOF efficiently removed NOC from real feedstocks to concentrations ~ 80 ppm which allowed ULSD production at much milder conditions to those used during pristine feedstocks HDT. Operating temperature could be significantly diminished (from 350 to 330 °C, at 56 kg cm−2 (5.77 MPa), LHSV = 1.5 h−1 , H2 /oil = 2500 ft3 bbl−1 (445 m3 m−3 )) which could notably prolong cycle life of NiMo/Al2 O3 formulation used.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"336 1","pages":"56"},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75472500","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Shale adhesion force measurements via atomic force microscopy","authors":"N. Mitiurev, M. Verrall, S. Shilobreeva, A. Keshavarz, S. Iglauer","doi":"10.2516/ogst/2021057","DOIUrl":"https://doi.org/10.2516/ogst/2021057","url":null,"abstract":"Wettability of sedimentary rock surface is an essential parameter that defines oil recovery and production rates of a reservoir. The discovery of wettability alteration in reservoirs, as well as complications that occur in analysis of heterogeneous sample, such as shale, for instance, have prompted scientists to look for the methods of wettability assessment at nanoscale. At the same time, bulk techniques, which are commonly applied, such as USBM (United States Bureau of Mines) or Amott tests, are not sensitive enough in cases with mixed wettability of rocks as they provide average wettability values of a core plug. Atomic Force Microscopy (AFM) has been identified as one of the methods that allow for measurement of adhesion forces between cantilever and sample surface in an exact location at nanoscale. These adhesion forces can be used to estimate wettability locally. Current research, however, shows that the correlation is not trivial. Moreover, adhesion force measurement via AFM has not been used extensively in studies with geological samples yet. In this study, the adhesion force values of the cantilever tip interaction with quartz inclusion on the shale sample surface, have been measured using the AFM technique. The adhesion force measured in this particular case was equal to the capillary force of water meniscus, formed between the sample surface and the cantilever tip. Experiments were conducted with a SiconG cantilever with (tip radius of 5 nm). The adhesion forces between quartz grain and cantilever tip were equal to 56.5 ± 5 nN. Assuming the surface of interaction to be half spherical, the adhesion force per area was 0.36 ± 0.03 nN/nm2. These measurements and results acquired at nano-scale will thus create a path towards much higher accuracy-wettability measurements and consequently better reservoir-scale predictions and improved underground operations.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"15 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"80930515","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Onset of intermittent flow: Visualization of flow structures","authors":"A. Arabi, Y. Salhi, Amina Bouderbal, Y. Zenati, E. Si-Ahmed, J. Legrand","doi":"10.2516/OGST/2021009","DOIUrl":"https://doi.org/10.2516/OGST/2021009","url":null,"abstract":"The transition from stratified to intermittent air-water two-phase flow was investigated experimentally, by flow visualization and pressure drop signals analyses, in a 30 mm ID pipe. The intermittent flow’s onset was found to be mainly dependent on the liquid superficial velocity and the pipe diameter. Plug flow, Less Aerated Slug (LAS) or Highly Aerated Slug (HAS) flows could be obtained on the gas superficial velocity grounds. The available models, compared to experiments, could not predict adequately the intermittent flow onset. The appearance of liquid slugs was revealed by peaks in the pressure drop signal. Furthermore, it was shown that the available slug frequency correlations were not valid in the zone of the onset of intermittent flow.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"91 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"83728645","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"The formation mechanism of authigenic chlorite in tight sandstone and its effect on tight oil adsorption during hydrocarbon filling","authors":"Qianshan Zhou, C. Li, Guojun Chen, Chengfu Lyu, Xuefeng Qu, Xiaofeng Ma, Chengze Li, Qihong Lei, Qichao Xie","doi":"10.2516/OGST/2021015","DOIUrl":"https://doi.org/10.2516/OGST/2021015","url":null,"abstract":"Authigenic chlorite, which is frequently found in sandstone, has a controlling effect on the reservoirs in which tight oil is adsorbed during hydrocarbon filling. In this study, the content, occurrence state, timing, mechanism and influence of authigenic chlorite on the micro-occurrence states of tight oil were studied using Thin Section (TS), Fluorescent Thin Section (FTS), X-Ray Diffraction (XRD), Field Emission-Scanning Electron Microscopy (FE-SEM), Environmental Scanning Electron Microscopy (ESEM), and Energy Dispersive Spectroscopy (EDS). The results indicate: (1) a spatial coupling between chlorite development, a brackish water delta front facies depositional environment, and biotite-rich arkosic sandstone. (2) Authigenic chlorite can be divided into three types: grain-coating chlorite, pore-lining chlorite, and rosette chlorite. Chlorite forms after early compaction but before other diagenetic phases, and grows via precipitation from pore waters that contain products released during the dissolution of volcanic rock fragments and biotites. Porewater is also pressure-released from feldspars and mudstone. (3) The micro-occurrence states of tight oil can be divided into five types: emulsion form, cluster form, throat form, thin-film form, and the isolated or agglomerated particle form. (4) During hydrocarbon filling, tight oil mainly occurs on the surface of grain-coating and pore-lining chlorite in the form of a thin film, the granular or agglomerated forms are mainly enriched within the intercrystalline pores within the authigenic chlorite, and the cluster forms are mainly enriched in dissolution pores. Isolated or agglomerated particles of tight oil primarily occur in the intercrystalline pores of the rosette chlorite. (5) The specific surface area and the authigenic chlorite’s adsorption potential of authigenic chlorite control the micro-occurrence of tight oil on the surface of the chlorite and in intercrystalline pores. The adsorption capacity of chlorite lies in the following order: pore-lining chlorite intercrystalline pores > rosette chlorite > chlorite in feldspar dissolution pores > pore-lining chlorite surface > grain-coating chlorite intercrystalline pores > grain-coating chlorite surface.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"23 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82852128","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Correlation and modelling of the penetration and softening point tests of bitumen binders with a variety of physical and chemical properties","authors":"Marvy Girgis, J. Barbier, A. Quignard, I. Merdrignac, J. Marques","doi":"10.2516/ogst/2021046","DOIUrl":"https://doi.org/10.2516/ogst/2021046","url":null,"abstract":"Studying bitumen has always posed a challenge to researchers owing to its extreme complexity and unique properties. To classify it commercially and to determine bitumen grade, two standard empirical tests have been adopted within the European standardized bitumen binders system [EN 12591:2009 (2009) Bitumen and bituminous binders – Specifications for paving grade bitumens]: Softening Point (SP) and Penetration (PEN). The relationship between these two tests and the physical or chemical properties of bitumen is not well understood. For the first time, this study represents an attempt to build more understanding of such a relationship through a comprehensive study of the correlation between the two standard tests and many physical and chemical properties of bitumen. A second goal is to propose some predictive models for these two tests and compare their predictive accuracy. Therefore, 13 Straight Run Vacuum Residues (SRVR) samples from different geographical origins were analyzed to measure the following parameters: Dynamic Viscosity (VisDy), Conradson Carbon Residue (CCR), C5 Asphaltenes Content (AspC5), C7 Asphaltenes Content (AspC7), Elemental Analysis (including C, H, O, N, S, Ni, and V content), Simulated Distillation (SD), Fourier-Transform Infrared Spectroscopy (FT-IR), and proton nuclear magnetic resonance spectroscopy (H-NMR). Results of studying correlations using correlation matrix and Principal Component Analysis (PCA) have emphasized the prominent effect of asphaltenes content on the other properties and the results of SP and PEN. It has also shown the potential importance of the aliphaticity/aromaticity of bitumen. Then, four models were proposed for the prediction of SP and PEN: viscosity, FT-IR, H-NMR, and multi-parameter models. Partial least squares (PLS) regression was used for building all models, except viscosity ones. All SP models, except H-NMR model, exhibited very good accuracy compared to the standard method. On the other hand, PEN was more difficult to predict than SP and only the multi-parameter model of PEN showed relatively good accuracy of prediction.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"40 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"78086119","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"Prediction of engine NOx for virtual sensor using deep neural network and genetic algorithm","authors":"Jongmyung Kim, Jihwan Park, Seunghyup Shin, Yongjoo Lee, K. Min, Sangyul Lee, Minjae Kim","doi":"10.2516/ogst/2021054","DOIUrl":"https://doi.org/10.2516/ogst/2021054","url":null,"abstract":"The Nitrogen Oxides (NOx) from engines aggravate natural environment and human health. Institutional regulations have attempted to protect the human body from them, while car manufacturers have tried to make NOx free vehicles. The formation of NOx emissions is highly dependent on the engine operating conditions and being able to predict NOx emissions would significantly help in enabling their reduction. This study investigates advanced method of predicting vehicle NOx emissions in pursuit of the sensorless engine. Sensors inside the engine are required to measure the operating condition. However, they can be removed or reduced if the sensing object such as the engine NOx emissions can be accurately predicted with a virtual model. This would result in cost reductions and overcome the sensor durability problem. To achieve such a goal, researchers have studied numerical analysis for the relationship between emissions and engine operating conditions. Also, a Deep Neural Network (DNN) is applied recently as a solution. However, the prediction accuracies were often not satisfactory where hyperparameter optimization was either overlooked or conducted manually. Therefore, this study proposes a virtual NOx sensor model based on the hyperparameter optimization. A Genetic Algorithm (GA) was adopted to establish a global optimum with DNN. Epoch size and learning rate are employed as the design variables, and R-squared based user defined function is adopted as the object function of GA. As a result, a more accurate and reliable virtual NOx sensor with the possibility of a sensorless engine could be developed and verified.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"42 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75722830","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

{"title":"An integrated gas-oil and bio-diesel supply network model with strategic and tactical applications considering the environmental aspects","authors":"Seyed Meysam Rafie, H. Sahebi","doi":"10.2516/ogst/2021021","DOIUrl":"https://doi.org/10.2516/ogst/2021021","url":null,"abstract":"In recent years, research has shown that biomass can be a source of energy to replace fossil fuels and effectively reduce current environmental crises. Researchers have studied how biofuels are supplied through the oil supply chain to achieve tangible results. This paper presents an optimization model for the gas-oil and biodiesel supply chains suggesting the optimization of both supply chains simultaneously for the first time. The proposed model deals with the connection points of two supply chains and determines the two chains’ connection points by considering two economic and environmental objective functions. The model can be used to make decisions on issues such as location, allocation, production planning, inventory management, capacity expansion, and so forth. The proposed programming model’s performance has been studied through a real case study in Iran and the sensitivity analyses have been performed. The ε-constraint method was used to solve the multi-objective model. The proposed model is expected to be effective in the future management of countries’ fuel sources, particularly to be used as an alternative to fossil fuels. Also, this research can provide a basis for more extensive research on fuel supply chain integration.","PeriodicalId":19424,"journal":{"name":"Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles","volume":"176 1","pages":""},"PeriodicalIF":1.5,"publicationDate":"2021-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"77471916","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}