Jsme International Journal Series A-solid Mechanics and Material Engineering最新文献_第6页

Residual Stress and Its Effect on Yielding in SiC/Ti Plate SiC/Ti板残余应力及其对屈服的影响

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.25

F. Zhou, R. Hashimoto, A. Ogawa, Y. Sofue

引用次数: 2

Investigation of High-Strength Electroformed Ni for Microprobes 微探针用高强度电铸镍的研究

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.79

T. Kimura, N. Arita, H. Fukinbara, T. Hattori

引用次数: 1

Fabrication of Composite Material Using Alumina Agglomerated Sludge and Aluminum Powder by Spark Plasma Sintering 火花等离子烧结制备氧化铝凝聚污泥与铝粉复合材料

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.91

I. Fukumoto, S. Mekaru, S. Shibata, K. Nakayama

引用次数: 18

Development of Newly Designed Ultra-Light Core Structures 新设计超轻核心结构的发展

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.38

T. Nojima, Kazuya Saito

引用次数: 77

Unified Constitutive Equations of Viscoplastic Deformation: Development and Capabilities 粘塑性变形统一本构方程:发展与能力

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.138

K.-C. Ho

引用次数: 7

Biomechanical Study on Distal Filling Effects in Cementless Total Hip Replacement 无骨水泥全髋关节置换术中远端填充效果的生物力学研究

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.147

S. Chae, Jun hyoung Lee, H. Choi

引用次数: 6

AE Monitoring of Microdamages in Bioceramics for Artificial Joints under Simulated Body Environment 模拟人体环境下生物陶瓷人工关节微损伤的声发射监测

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.11

S. Wakayama, Yasuhiro Suzuki, T. Oshima, Satoshi Kobayashi

{"title":"AE Monitoring of Microdamages in Bioceramics for Artificial Joints under Simulated Body Environment","authors":"S. Wakayama, Yasuhiro Suzuki, T. Oshima, Satoshi Kobayashi","doi":"10.1299/JSMEA.49.11","DOIUrl":"https://doi.org/10.1299/JSMEA.49.11","url":null,"abstract":"Microfracture process of 3 mol% yttria stabilized zirconia (3Y-TZP) for artiﬁcial joints was evaluated using the acoustic emission technique. In order to investigate the e ﬀ ects of environment and strain rate on the microfracture process, four point bending tests were carried out in air and physiological saline (P.S.) at various loading rates. From the results of AE behavior, rapid AE increasing point was observed before the ﬁnal unstable fracture. It was suggested from the previous work that the AE increasing point corresponds to the maincrack formation. The critical stress for maincrack formation, σ C , was determined from the bending stress at the AE increasing point. The critical stress as well as bending strength, σ B , decreased in physiological saline. In particular, the decrease in critical stress was remarkable. It was then understood that stress corrosion cracking (SCC) by water in physiological saline a ﬀ ected maincrack formation rather than the ﬁnal fracture. Consequently, it was suggested that the evaluation of σ C is essential for the reliability assessment of bioceramics.","PeriodicalId":170519,"journal":{"name":"Jsme International Journal Series A-solid Mechanics and Material Engineering","volume":"17 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-01-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125269333","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 1

Evaluation of Adhesive Behaviors of Chromium Nitride Coating Films Produced by Arc Ion Plating Method 电弧离子镀法制备氮化铬涂层的粘接性能评价

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.123

R. Murakami, Yun-Hae Kim, Kazushi Kimura, D. Yonekura, Do-Hoon Shin

{"title":"Evaluation of Adhesive Behaviors of Chromium Nitride Coating Films Produced by Arc Ion Plating Method","authors":"R. Murakami, Yun-Hae Kim, Kazushi Kimura, D. Yonekura, Do-Hoon Shin","doi":"10.1299/JSMEA.49.123","DOIUrl":"https://doi.org/10.1299/JSMEA.49.123","url":null,"abstract":"Scratch tests and pin-on-disk wear tests were performed to clarify the cracking and delaminating behavior of CrN coatings. The CrN films were coated onto an aluminum alloy substrate, JIS A2024, by an arc ion plating method. Eight types of single-layered coating and multilayered coatings were prepared by changing the bias voltage during the deposition. LCI and LCII values were not improved by increasing the number of layers. The critical loads of the single-layered coatings decreased with increasing the bias voltage. It appears that, for the multilayered coatings, the combination of bias voltages influenced the critical loads. The critical loads strongly depended on dynamic hardness and Young’s modulus. In particular, the critical loads of the multilayered coatings were influenced by the properties of the intermediate and bottom layers as well as the surface roughness, hardness and Young’s modulus of the top layer. The large film delamination for single-layered coatings deposited using a high bias voltage occurred during pin-on-disk wear tests even though the critical loads of the single-layered coatings were higher than those of the multilayered coatings. If the brittle top layer could be broken and delaminated by the sliding contact, the ductile bottom layer coated under a bias voltage of 0V could endure the complete delamination of film.","PeriodicalId":170519,"journal":{"name":"Jsme International Journal Series A-solid Mechanics and Material Engineering","volume":"239 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-01-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121870682","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 3

Coupled Deformation Properties of Anti-Symmetrical Laminate Composites 非对称层压板复合材料的耦合变形特性

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.43

M. Hojo, R. Hashimoto, A. Ogawa

引用次数: 0

Development of High Performance CFRP/Metal Active Laminates 高性能CFRP/金属活性层压板的研制

Jsme International Journal Series A-solid Mechanics and Material Engineering Pub Date : 2006-01-15 DOI: 10.1299/JSMEA.49.32

H. Asanuma, O. Haga, M. Imori

{"title":"Development of High Performance CFRP/Metal Active Laminates","authors":"H. Asanuma, O. Haga, M. Imori","doi":"10.1299/JSMEA.49.32","DOIUrl":"https://doi.org/10.1299/JSMEA.49.32","url":null,"abstract":"This paper describes development of high performance CFRP/metal active laminates mainly by investigating the kind and thickness of the metal. Various types of the laminates were made by hot-pressing of an aluminum, aluminum alloys, a stainless steel and a titanium for the metal layer as a high CTE material, a unidirectional CFRP prepreg as a low CTE/electric resistance heating material, a unidirectional KFRP prepreg as a low CTE/insulating material. The aluminum and its alloy type laminates have almost the same and the highest room temperature curvatures and they linearly change with increasing temperature up to their fabrication temperature. The curvature of the stainless steel type jumps from one to another around its fabrication temperature, whereas the titanium type causes a double curvature and its change becomes complicated. The output force of the stainless steel type attains the highest of the three under the same thickness. The aluminum type successfully increased its output force by increasing its thickness and using its alloys. The electric resistance of the CFRP layer can be used to monitor the temperature, that is, the curvature of the active laminate because the curvature is a function of temperature.","PeriodicalId":170519,"journal":{"name":"Jsme International Journal Series A-solid Mechanics and Material Engineering","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2006-01-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121001215","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}

引用次数: 4