{"title":"Constraint transformation for IC physical design","authors":"E. Malavasi, E. Charbon","doi":"10.1109/IWSTM.1998.729767","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729767","url":null,"abstract":"In a top-down design methodology, design tasks are divided into simpler sub-tasks across levels of hierarchy and abstraction as an effective divide-and-conquer technique. For every task, tolerances are defined on all performance characteristics to take into account parasitics, mismatches and other nondeterministic process parameter variations. Constraint transformation is a process used to translate performance specifications into sub-task requirements. This paper introduces the problem of constraint transformation and describes some formal solutions for analog circuit applications. Examples illustrate the methodology and show the suitability of this approach for industrial-strength applications.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"34 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132826315","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Efficient yield estimation within automated analog IC design","authors":"G. Gielen, G. Debyser, F. Leyn, W. Sansen","doi":"10.1109/IWSTM.1998.729788","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729788","url":null,"abstract":"A new statistical design methodology is presented that uses symbolic methods to increase the efficiency of statistical IC design. The methodology is implemented in an environment that combines the symbolic design equation manipulation engine DONALD with the generic statistical design system GOSSIP. DONALD is used to generate the initial design and to create the symbolic computational plan that is used by GOSSIP for the actual statistical yield, Cp and Cpk optimization, where Cp, Cpk are process capability indices. The strengths and weaknesses of the proposed approach are discussed, and its accuracy and speed are compared with the traditional method of using a SPICE-type circuit simulator in the inner loop of the statistical optimization. Overall, a significant speed-up of the statistical IC design efficiency is observed.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"49 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122172262","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
M. Quarantelli, L. Daldoss, P. Gubian, C. Guardiani
{"title":"Predictive tolerance and sensitivity analysis based on parametric response surface methodology","authors":"M. Quarantelli, L. Daldoss, P. Gubian, C. Guardiani","doi":"10.1109/IWSTM.1998.729784","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729784","url":null,"abstract":"An innovative methodology aimed at deriving predictive response surface models for the variability of VLSI mixed-signal basic building block performances is explored in this paper. The purpose of this methodology is two-fold. First, we plan to be able to predict the sensitivity to process variations of basic ingredients of VLSI design, such as embedded memories, full custom and analog components. This can greatly enhance the capability of concurrently developing process, device, and circuit design, which is considered to be a key factor for system-on-chip designs. Secondly, the availability of parameterized process variability predictors together with functional macromodels of basic circuit components is the basis for top-down design and manufacturability analysis and optimization of large analog and mixed signal sub-systems. In our experiment, we studied the propagation delay and the power dissipation of an SRAM sense amplifier which has been characterized for three different state-of-the-art CMOS technologies, with 0.35, 0.25, and 0.18 /spl mu/m minimum gate length. We propose use of the response surface methodology (RSM) to compute performance sensitivities to low-level parameters. Finally, we use a sensitivity analysis to investigate the potential for technology-independent (i.e. parameterized) macromodels to be used in efficient hierarchical statistical analysis.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130235011","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Runs rules for bivariate Shewhart chart","authors":"A. Chen, R. Guo, C.-L. Lee","doi":"10.1109/IWSTM.1998.729787","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729787","url":null,"abstract":"Among the various statistical process control (SPC) charts, the Shewhart chart (Shewhart, Economic Control of Quality Improvement, Van Nostrand Reinhold, 1931) has been the most used control chart in practice due to its simplicity and explicit representation. In many practical situations, there are two or more related quality characteristics that must be monitored simultaneously. The Shewhart chart used at present is inefficient for monitoring multiple variables and lacks the capability to consider the relationships between variables. In this paper, we develop runs rules for the Shewhart chart to control bivariate data. The results show that the Shewhart chart with runs rules is comparable, and in some cases superior, to the T/sup 2/ control chart. We use the thickness data of an SiO/sub 2/ layer as an example to illustrate the methodology.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"24 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125220308","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Intrafield effects and device manufacturability: a statistical simulation approach","authors":"Z. Krivokapic, A. Minvielle, W.D. Heavlin","doi":"10.1109/IWSTM.1998.729764","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729764","url":null,"abstract":"For sub-250 nm technologies, one of the major systematic sources of variation is the intrafield variation induced by the stepper lens imperfections on critical layers. Using well-calibrated process, device, and statistical simulators, we predict the effects of lens aberrations on the manufacturing distributions of gate critical dimensions, drive currents, and ring oscillators. For a case involving four dies per reticle field, we predict significantly different distributions per reticle field.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"349 2","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114015197","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
J.C. Davis, S. Rao, K. Vasanth, S. Saxena, R. Burch, P. K. Mozumder
{"title":"Statistical aspects of tuning simulators to noisy data","authors":"J.C. Davis, S. Rao, K. Vasanth, S. Saxena, R. Burch, P. K. Mozumder","doi":"10.1109/IWSTM.1998.729757","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729757","url":null,"abstract":"The purpose of TCAD tools is to reduce the cost of developing new semiconductor technologies by replacing real wafers with simulations. If the process flows and device structures can be simulated accurately, then new device designs can be analyzed using simulations instead of real wafers. However, due to uncertainty in material coefficients and deficiencies in the physical models, process and device simulators often fail to provide the accuracy necessary for predictive device design, thereby limiting the impact of TCAD on device development cost. To address this problem, process and device simulators are often tuned to match experimental data, i.e. the simulator coefficients are adjusted such that the simulator outputs match experimentally measured data. However, the experimental data to which the simulators are tuned contain noise due to both process variation and measurement noise. Since tuning parameters are adjusted such that the simulator outputs, which are deterministic, match the experimental data, the uncertainty in the data implies uncertainty in the optimal values of the tuning parameters. This paper presents a methodology for tuning to uncertain and sparse experimental data and estimating the tuning parameter distribution based on the experimental data uncertainty. This distribution can be used to determine whether there is enough data to generate confidence in the optimal values of the tuned parameters. Additionally, we show how the tuned parameter distribution can be used to estimate the uncertainty in simulations conducted at conditions other than those used for tuning.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"253 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"134152887","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Impact of unrealistic worst case modeling on the performance of VLSI circuits in deep sub-micron CMOS technologies","authors":"A. Nardi, A. Neviani, E. Zanoni, C. Guardiani","doi":"10.1109/IWSTM.1998.729766","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729766","url":null,"abstract":"The impact of process fluctuations on the variability of deep sub-micron (DSM) VLSI circuit performances is investigated in this paper. In particular, we show that, as process dimensions scale down in the sub half-micron region, the relative weight of process variability tends to increase, thus wearing down a nonnegligible portion of the benefits that are expected from minimum feature size scaling. Therefore, in order to better exploit the advance of process technology, it is essential to adopt a realistic approach to worst case modeling, as in the assigned probability technique (APT) (Dal Fabbro et al, Proc. 32nd ACM/IEEE Design Automation Conf., pp. 702-6, 1995). The application of the APT technique to a 16-bit ripple-carry adder designed in 0.35 /spl mu/m, 0.25 /spl mu/m and 0.18 /spl mu/m CMOS technologies with a power supply ranging from 3.3 V down to 1 V demonstrates how the manufacturability of DSM designs is going to be a vital factor for the successful implementation of high performance or low-power systems in 0.18 /spl mu/m and lesser technologies.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"45 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131899991","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
D. Kapila, A. Jain, M. Nandakumar, S. Ashburn, K. Vasanth, S. Sridhar
{"title":"The effect of deterministic spatial variations in retrograde well implants on shallow trench isolation and latchup immunity","authors":"D. Kapila, A. Jain, M. Nandakumar, S. Ashburn, K. Vasanth, S. Sridhar","doi":"10.1109/IWSTM.1998.729774","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729774","url":null,"abstract":"The retrograde well implants for sub-0.18 /spl mu/m CMOS are done at a normal or near-normal incidence to minimize shadowing due to the thick photoresist edges. The endstation geometry in the high energy implanter results in an incident angle variation across the wafer, which causes strong spatial variations in the well profile and can negatively affect device performance. We show that the spatial variations can have significant impact on shallow trench isolation (STI), latchup immunity, well resistance and capacitance. The spatial variations can cause in a deterministic way the failure of a large number of isolation structures on a single wafer.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116849653","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Controlling mesh effects in integrated process and device simulation","authors":"V. Axelrad, M. Duane","doi":"10.1109/IWSTM.1998.729781","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729781","url":null,"abstract":"Mesh discretization effects can have a significant impact on obtaining meaningful results in statistical TCAD simulations. Discretization errors, i.e. inaccuracy of the solution due to too large or poorly shaped mesh elements, can be damaging in an absolute sense, as an offset of nominal values. Potentially even more dangerous are relative errors between statistical runs due to meshing noise, which can mask the desired sensitivity values, correlations, etc. This work discusses the application of an advancing-front mesh generation algorithm to study the sensitivity of MOSFET simulation results to (a) mesh density and (b) variation of physical process parameters (gate oxide thickness). It is shown that the utilized mesh generation algorithm can produce accurate results at low cost. In contrast to the conventional approach, results obtained using the new mesh are more accurate and vary smoothly in response to variation of physical input parameters, while requiring only about one third of the CPU time for a device simulation.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"19 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125874181","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Defect control using an automatic killer defect selection method","authors":"Yasuhiro Yoshitake, Shunji Maeda, Kenji Watanabe","doi":"10.1109/IWSTM.1998.729763","DOIUrl":"https://doi.org/10.1109/IWSTM.1998.729763","url":null,"abstract":"In LSI mass production lines, it is very important to improve the detection accuracy of fatal excursions in defect trend charts in order to ramp up quickly and maintain good yield. It is for this reason that killer defects which could cause device faults should be monitored. We have developed an automatic killer defect selection (AKIDS) method to assist and improve the accuracy of this process. This method judges defects as killer or nonkiller by comparing defect sizes against killer defect judgement criteria. We applied AKIDS in the defect QC and sampling review processes, and found it to be effective in both detecting fatal excursions and selecting good review points for identifying the source of device faults.","PeriodicalId":112436,"journal":{"name":"IWSM. 1998 3rd International Workshop on Statistical Metrology (Cat. No.98EX113)","volume":"7 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1998-06-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127998279","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}