Chien-Yi Peng, H. Sudarsanam, M. Hamasha, Susan S. Lu, T. Dhakal, C. Westgate
{"title":"Performance of aluminum-doped zinc oxide thin films under bending fatigue conditions","authors":"Chien-Yi Peng, H. Sudarsanam, M. Hamasha, Susan S. Lu, T. Dhakal, C. Westgate","doi":"10.1109/LISAT.2012.6223196","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223196","url":null,"abstract":"Aluminum-doped zinc oxide (AZO) film is a promising candidate for low cost transparent conductive oxide (TCO) applications. It is a viable alternative to indium tin oxide (ITO), the dominant material used in TCO. Although AZO has good electrical and optical properties, its mechanical properties must be thoroughly considered in the design and manufacturing of flexible devices. During the manufacture and use, thin films' are subjected to bending fatigue (cyclic bending) which leads to degradation and ultimately failure of the films. This work was designed to investigate the effects of the bending frequency, bending diameter, ways of bending, and number of bending cycles on the percentage change in electrical resistance (PCER) and transmittance of 575 nm thick AZO films, which were deposited on 127 μm Kapton substrate using RF-magnetron sputtering technique. Both the film and the substrate were subjected to cyclic bending test under controlled study parameters. The design of experiments technique (DOE) was used to investigate the significant factors on the PCER as well as to provide an average estimate of the effect of each factor and two-factor interaction through the main effects plot and the two-factor interaction plot, respectively. Moreover, the transmittance spectra were studied at different number of bending cycles. The primary result shows that the PCER is very sensitive to all study parameters. However, it increases rapidly in the first 400 bending cycles and then increases linearly until 1000 bending cycles. The result also points out that the PCER is large while the small bending diameter and low bending frequency are applied. Also the two ways bending experiment leads to the larger PCER compared with the one way bending test. The fresh films average transmittance (from 660 to 950 nm wavelength) is 59.6%, which decreased to about 3.4% after 1000 cycles of bending.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"2 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129416122","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Wadoo, Sadiksha Sapkota, Keerthish Chagachagere
{"title":"Optimal control of an autonomous underwater vehicle","authors":"S. Wadoo, Sadiksha Sapkota, Keerthish Chagachagere","doi":"10.1109/LISAT.2012.6223100","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223100","url":null,"abstract":"This paper presents the optimal control of the kinematic model of an autonomous underwater vehicle. An optimal feedback control methodology is developed for the trajectory tracking of underwater vehicles. The motion of underwater vehicles is presented first as a kinematic model. For the design of feedback control, the system is linearized and transformed into a chained form. The control for trajectory tracking of the kinematic model is presented as an H-2 optimal design. Formulating LQG as H-2 optimization is useful as it can be generalized to include frequency-domain performance specifications.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"29 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129417336","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The impact of major catastrophes on the global supply chain: Facility planning and inventory considerations","authors":"C. Axelrod","doi":"10.1109/LISAT.2012.6223097","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223097","url":null,"abstract":"In this paper, the author extends a prior model of supply-chain commonalities [1] to incorporate the impact of major catastrophes. Such disastrous events as the September 11, 2001 attack on New York's World Trade Center and the earthquake and tsunami that hit north-eastern Japan on March 11, 2011 wreak havoc with supply chains even when well-planned diversification and disaster-recovery strategies have been developed and implemented. Concepts are included from the author's prior work [2] on how organizations must develop and test catastrophe contingency plans. These recommended practices are applied to supply chains in order that they will survive major catastrophic events, which might harm regular disaster-backup staff, and which might destroy or severely damage systems and facilities. We extend the scope of commonality beyond individual producers and factories to extensive physical geographical areas and to virtual regions. Since catastrophe risk mitigation strategies must be both financially and operationally effective, we examine the geographical and logical diversification of facilities and distribution channels and suggest inventory cushions needed to reduce the impact of extended recovery times. This paper examines factors that need to be included in the analysis and suggests investments needed to reduce corresponding risks.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"40 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124726348","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Implementation and design of a low cost laser diode temperature controller","authors":"R. Piersiak","doi":"10.1109/LISAT.2012.6223197","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223197","url":null,"abstract":"It has become apparent that many commercial products and military applications require high-endurance laser diodes. Testing the life cycles of laser diodes currently requires large and expensive equipment that is overreaching in terms of the overall goal. Finding a cheap and minimalistic solution will provide a large sample size and allow for rapid testing of hundreds of lasers. This paper aims to log the process of designing and implementing a temperature controller system for laser diodes. This system will use a thermoelectric cooler (TEC) to harness control of the Peltier effect to maintain a constant temperature on a laser diode. The system will contain a combination of hardware and software that work intimately to provide an intuitive and simple method of testing the life cycle of a laser diode. The hardware will consist of a cooling fan, heat sink, TEC, and metal plate that constitute the testing apparatus. The software will work with a number of peripherals to provide a steady temperature during testing and rapid transition between different temperature set points. The software will need to control the drive current to the TEC using a software-based PID (Proportional-Integral-Differential) controller and function as a watchdog, capable of giving error messages and raising alarms. The primary purpose of the temperature controller is to perform endurance testing on laser diodes. It will also free up high cost equipment for precision needs, rather than endurance testing. This system aims to maintain a constant temperature within 0.5°C of the set point. This will guarantee a relatively stable and consistent light-intensity on the laser diode. The basic model of this temperature controller can be scaled and/or modified for applications other than laser diodes. This expands the potential impact of this system to be more consumer-friendly and will provide individuals with their own low cost temperature controller.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"5 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129718538","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Smart textiles based wireless ECG system","authors":"A. Alzaidi, Linfeng Zhang, H. Bajwa","doi":"10.1109/LISAT.2012.6223206","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223206","url":null,"abstract":"Advances in polymers, soft-electronics, biosensors and mobile communication, have led to a growing interest in wireless Electrocardiogram (ECG) monitors. A wide variety of textile-based wireless ECG sensors and systems have been developed [1, 2]. Typically, such wireless ECG systems rely on miniature ECG sensor/electrode that can be worn as badges, patches, or jewelry to measure and show advance reactions. Smart textile and non-contact electrodes have also been reported recently. The earlier stage of smart clothing usually tether conventional electrode sensors or devices attached to the textile. Such approaches have their limitations such as discomfort and integration with the fabric. In this paper, a wireless ECG system using smart textiles sensor is presented. Non-contact ECG electrode, developed with intelligent materials and different textile technologies, is an integral part of wireless ECG system. Such electrodes with integrated nanostructure conformal antenna can use a wireless transmitter to send data to any external device for remote health monitoring, telemedicine and health delivery. The paper will also present the design of the textile based integrated conformal patch antenna as well as system level radio design that could be integrated with the textile based conformable antenna and proposed ECG electrode.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"61 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124566155","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"XSSmon: A Perl based IDS for the detection of potential XSS attacks","authors":"C. Frenz, Jong P. Yoon","doi":"10.1109/LISAT.2012.6223107","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223107","url":null,"abstract":"Recent years have seen an explosion in the number of cross site scripting (XSS) incidents effecting Web sites and Web applications. As such, an intrusion detection system (IDS) capable of detecting potential cross site scripting attacks is demonstrated. The IDS involves the capturing of potential client side executable content on a Web page and the hashing of that content. At a future point in time, the Web page is reprocessed for client side executable content and the content rehashed, with any differences in the hash values indicative of a potential XSS attack. It is believed that the described IDS technique would be particularly useful for Web forums and other user content driven site, since the IDS only considers content recognized as potentially executable and not normal text content, such as that which would be typically enclosed in paragraph or heading tags.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"137 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115904280","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A cross layer, adaptive data aggregation algorithm utilizing spatial and temporal correlation for fault tolerant Wireless Sensor Networks","authors":"B. Beheshti, H. Michel","doi":"10.1109/LISAT.2012.6223204","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223204","url":null,"abstract":"Wireless Sensor Networks (WSNs) are ad hoc networks formed by tiny, low powered, and low cost devices. WSNs take advantage of distributed sensing capability of the sensor nodes such that several sensors can be used collaboratively to detect events or perform monitoring of specific environmental attributes. Since sensor nodes are often exposed to harsh environmental elements, and normally operate in an unsupervised fashion over long periods of time, within their MTBF, some of them are subject to partial failure in form of A/D readings that are permanently off the correct levels. Additionally, due to glitches in timing and in hardware or software, even healthy sensor nodes can occasionally report readings that are outside of the expected range. In this paper we present a novel approach that combines spatial and temporal correlation of the data collected by neighboring sensors to combat both error modes described above. We combine the weighted averaging algorithm across multiple sensors, with the LMS adaptive filtering of individual sensor data, in order to improve fault tolerance of WSNs. We present performance gains achieved by combining these methods; and analyze the computational and memory costs of these algorithms.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"12 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126664512","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Engineered nanoparticles for targeted drug delivery","authors":"Matthew Breland, Badal Patel, Hassan Bajwa","doi":"10.1109/LISAT.2012.6223198","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223198","url":null,"abstract":"DNA based nanostructures and advances in DNA origami techniques have shown great potential in fabrication and of nanostructures and devices. Though a large number of DNA origami structures have been reported [1-3], very few applications of DNA structures have been presented. Custom shapes formed by programmable DNA self assembly can be used to engineer nanoscale devices such as a biological antenna. The focus of our research is to design a nanoscale antenna using DNA biostructure as a scaffold. Conductivity of such a biological antenna can be achieved by using conductive nanoparticles coating on DNA [4] or by attaching conducting polymers to DNA structures[5]. In this paper, we will present design of engineered nano-antennas with well defined engineering characteristics. Engineered nano-antennas have a resonant frequency, that can be used for diagnostic and drug delivery. The ability of such antennas to resonate at a particular frequency will give researchers the ability to communicate and control the nanoparticles. Such nanoparticles are carriers that can be used as advanced detection systems to help identifying toxicity of nanoparticles in the body. Organic molecules, such as folic acid, can be easily bonded to the surface of antenna to detect cancerous cells. We will further discuss detailed DNA origami techniques that can be used to realize such nanostructures.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"91 2 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116300035","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Steganography by multipoint Arabic letters","authors":"A. Odeh, A. AlZubi, Q. B. Hani, K. Elleithy","doi":"10.1109/LISAT.2012.6223209","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223209","url":null,"abstract":"Security methodologies are taken into consideration for many applications, where transferring sensitive data over network must be protected from any intermediate attacker. Privacy of data can be granted using encryption, by changing transmitted data into cipher form. Apart from encryption, hiding data represents another technique to transfer data without being noticeable by an attacker. This technique is called Steganography. In this paper, we will discuss the main concepts of Steganography and a carrier media that is used for this goal. Employing text as mask for other text represents the most difficult method that can be used to hide data. We will discuss some algorithms that use Arabic text. We then describe our doted space methodology to enhance data hiding.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"118 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116364163","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A LEGO based undergraduate control systems laboratory","authors":"S. Wadoo, R. Jain","doi":"10.1109/LISAT.2012.6223207","DOIUrl":"https://doi.org/10.1109/LISAT.2012.6223207","url":null,"abstract":"The cost of establishing a traditional control systems laboratory usually runs into many thousands of dollars. This paper introduces an alternative method of teaching a control systems laboratory for undergraduate engineering students using LEGO NXT kits and ROBOTC software. The total cost of the kit and the software is under $350 which makes this combination a very cheap alternative for establishing a control systems laboratory. The set of experiments described here are ideal for colleges and universities that wish to introduce a control system laboratory curriculum at a minimal cost. In the first experiment the students observe and explore the working of the inbuilt ROBOTC PID controller for the LEGO NXT motor. In the second experiment, tuning of the PID controller assuming the system equations of the LEGO NXT motor system are unknown is studied. Ziegler-Nichols (Z-N) method and its Tyreus-Luyben (T-L) modification are also studied. In the third experiment, the transfer function of the LEGO NXT motor is derived using system identification by the experimental data modeling approach. PID control design using the new model is then finally studied in the fourth experiment using the experimentally obtained transfer function.","PeriodicalId":445446,"journal":{"name":"2012 IEEE Long Island Systems, Applications and Technology Conference (LISAT)","volume":"2374 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2012-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127477180","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}