{"title":"Effective metal cleaning to increase MTBC by scanning ECR plasma (Conference Presentation)","authors":"K. Hirota, Nanako Tamari, S. Shirayone, M. Sumiya","doi":"10.1117/12.2514932","DOIUrl":"https://doi.org/10.1117/12.2514932","url":null,"abstract":"Plasma etching requires the nanometer scale precision control of the etched structures without particle generation which is a key factor of the defect and the yield ratio. Nevertheless, process drifts [1] and particles flaking off from the chamber wall are frequently observed in case of non-volatile metal accumulation on a chamber wall, because cleaning of metal by-product is more difficult than other by-products such as silicon and carbon. R Ramos et al [2] have reported the effective cleaning to reduce AlFx residue. However, sometimes, an etching of non-volatile chamber wall materials such as Al2O3 and Y2O3 at the same time by metal cleaning chemistries becomes the root cause of the particle and decreasing MTBC(mean time between clean). Therefore, it is important not to generate particles flaking off in mass production.\u0000In this study, effective AlFx cleaning was evaluated without chamber wall damage by microwave ECR plasma etching system. At first, effective AlFx cleaning was quantified by using in-situ FTIR equipment attached to the chamber side wall. The FTIR data showed that BCl3/Cl2 chemistry was higher cleaning efficiency than other chemistries such as Cl2, SiCl4/Cl2 and SF6/O2 for removing AlFx residue as mentioned previous study [2]. Second, Al2O3 etch rate distribution were measured using Al2O3 coupon sample simulating AlFx deposition. In this experiment, Al2O3 coupons were set in different locations such as top plate, sleeve and susceptor near the wafer stage. One of the unique characteristics of ECR plasma is that plasma generation position (ECR height) is movable by changing solenoid coil setting. After exposing BCl3/Cl2 plasma with two kinds of ECR heights at 146.8 and 197.2 mm from ESC (Electrostatic chuck) position, Al2O3 etch rates were measured. High ECR plasma (197.2 mm) showed higher Al2O3 etch rate at high chamber location such as top plate, while low ECR plasma (146.8 mm) showed higher Al2O3 etch rate at lower chamber location such as sleeve and susceptor. The scanning ECR height improves clean uniformity in the chamber. Also, ECR plasma has an advantage in reducing chamber wall damage by spattering non-volatile chamber wall materials with plasma to be able to control ECR height away from chamber walls.\u0000To evaluate long-term process stability of BCl3/Cl2 cleaning, marathon tests of 500 alumina wafers were executed. The Al2O3 wafers were etched by fluorine-based gas chemistry to generate AlFx residue. The two kinds of plasma cleaning every three Al2O3 wafers were evaluated. One was BCl3/Cl2 cleaning and the following SF6/O2 cleaning. The other was only SF6/O2 cleaning. As a result, particle count was stable during 500 wafers with BCl3/Cl2 cleaning while particle increased after 200 wafers without BCl3/Cl2 cleaning. The increased particle component was mainly Al. Therefore, the ECR plasma with scanning BCl3/Cl2 metal cleaning which could remove Al2O3 at the every corner, enables us to increase MTBC in etching mass productions ","PeriodicalId":433139,"journal":{"name":"Advanced Etch Technology for Nanopatterning VIII","volume":"14 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2019-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122234127","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Kal, Y. Oniki, Matthew Falugh, Cheryl Pereira, Qi Wang, F. Holsteyns, Jeffrey T. Smith, A. Mosden, K. Kumar, J. Boemmels, J. Ryckaert, P. Biolsi, T. Hurd
{"title":"Enabling complimentary FET (CFET) fabrication: selective, isotropic etch of Group IV semiconductors (Conference Presentation)","authors":"S. Kal, Y. Oniki, Matthew Falugh, Cheryl Pereira, Qi Wang, F. Holsteyns, Jeffrey T. Smith, A. Mosden, K. Kumar, J. Boemmels, J. Ryckaert, P. Biolsi, T. Hurd","doi":"10.1117/12.2514741","DOIUrl":"https://doi.org/10.1117/12.2514741","url":null,"abstract":"Area scaling without compromising on performance has become a challenge for technology nodes beyond N7. Gate all-around (GAA) device architecture for N5 and beyond technology nodes is emerging as a promising solution and is being heavily investigated by the semiconductor industry. Imec has recently demonstrated that GAA transistor design offers 50% area scaling for both standard cells and SRAM memory cells, by stacking NMOS and PMOS wires on top of each other (also called complimentary FET (CFET)). In addition, design technology co-optimization analysis indicates that CFET architectures meet the N3 power and performance requirements (Ryckaert et.al.; SPIE 2018, VLSI technology symposium 2018). However, integration and fabrication of such CFET architectures become significantly challenging. A primary requirement for GAA (CFET or separate NMOS/PMOS) devices is the formation of silicon channels / nanowires (NW)/nanosheets (NS). For CFET fabrication, a quintessential challenge is an etching method which can provide required selectivity to recess an epitaxially grown material selective to either NMOS or PMOS channel materials into a low-k gate spacer with adequate etch selectivity in an isotropic manner such that stacked wires or sheets can be formed either sequentially or simultaneously.\u0000\u0000 In the article, we will focus mainly on the Si NW/NS formation (or SiGe etch). Fabricating such NW/NS architecture requires two extremely selective, isotropic, and precise SiGe etches. As shown in Fig.1, step 2 (“SiGe cavity etch”) & step 8 (“channel release”). After the “SiGe cavity etch”, an ALD film of low-k spacer is deposited as the inner spacer (Fig.1, step 3). The SiGe cavity etch (Fig.1, step2) must be controlled with an extreme accuracy and have a straight etch front. The cavity etch will effectively define the inner spacer thickness in the area above and below the Si NW, after the inner spacer etch (step 4, Fig.1). A precise SiGe etch control is essential for the cavity formation, because: (1) if the SiGe recess is below target, the reformed inner spacer thickness will be under specification and may result in high parasitic capacitance between gate and source/drain expected. (2) If the SiGe recess is above target, the reformed inner spacer will penetrate into the replacement gate and will decrease the amount of gate metal wrapping around the nanowire and may impact channel length (Lg). Furthermore, in addition to the above requirements, etch selectivity towards the dummy gate, hard mask, oxide (STI, ILD0), and low K material around the gate (as shown in Fig 1) is essential. We will also demonstrate the process performance for “channel release” as mentioned earlier (Fig 1, step 8) and inner spacer etch (Fig 1, step 4) .To address the requirements described above, a process flow enabled with extremely high selective etches, where the selectivity is a function of film properties and/or etch chemistry is a quintessential advantage. In this article, we will de","PeriodicalId":433139,"journal":{"name":"Advanced Etch Technology for Nanopatterning VIII","volume":"9 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2019-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"117013005","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Promises of metasurfaces and challenges in scaling to mass production (Conference Presentation)","authors":"R. Devlin, J. Graff, P. Latawiec","doi":"10.1117/12.2514825","DOIUrl":"https://doi.org/10.1117/12.2514825","url":null,"abstract":"","PeriodicalId":433139,"journal":{"name":"Advanced Etch Technology for Nanopatterning VIII","volume":"170 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2019-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115998986","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Scaling below 3nm node: the 3D CMOS integration paradigm (Conference Presentation)","authors":"J. Ryckaert","doi":"10.1117/12.2517767","DOIUrl":"https://doi.org/10.1117/12.2517767","url":null,"abstract":"With the diminishing PPAC returns from dimensional scaling of CMOS technologies, new avenues to maintain the scaling roadmap need to be explored. Design-Technology Co-Optimization has succeeded in leveraging specific integration techniques to alleviate scaling bottlenecks of some critical design rules both in SRAM as well as logic cells. Unfortunately, these building blocks are now reaching records in compactness reducing the amount of integration opportunities to enhance their further scaling. The 3rd dimension has been seen for a long time as a holy grail that could unlock many design constructs bottlenecks in advanced CMOS technology nodes. Many of these attempts have failed in providing a universal solution for CMOS platforms. However, an optimal usage of the 3rd dimension can be found in some specific cases by a careful understanding of the design context. We will review in this talk few 3D CMOS integration techniques that offer new scaling opportunities for future technology nodes. Among these approaches we will explore the usage of buried interconnects for power delivery, the use of vertically oriented FETs for on-chip memory as well as a disruptive device built out of the stack of a pFET and an nFET into a single structure called CFET. In the latter, we will explore its scaling potential as a means to position it as a future general purpose device solution for CMOS logic as well as SRAM.","PeriodicalId":433139,"journal":{"name":"Advanced Etch Technology for Nanopatterning VIII","volume":"34 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2019-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116770323","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
A. Mameli, M. Verheijen, A. Mackus, F. Roozeboom, E. Kessels
{"title":"Isotropic atomic layer etching of ZnO using acetylacetone and O2 plasma (Conference Presentation)","authors":"A. Mameli, M. Verheijen, A. Mackus, F. Roozeboom, E. Kessels","doi":"10.1117/12.2514645","DOIUrl":"https://doi.org/10.1117/12.2514645","url":null,"abstract":"The continuous driving force from the semiconductor industry for realizing smaller features and device structures with higher density and higher-aspect ratio poses increasing challenges in traditional etching techniques. Atomic layer etching (ALE) provides the opportunity to overcome the shortcomings of more conventional etching processes. Extensive research in this field has led to the development of two main classes: plasma ALE to achieve anisotropic etching and thermal ALE for the isotropic counterpart. Besides anisotropic etching, plasma can also be applied for achieving isotropic etch profiles. Yet, this process option has not been explored extensively.\u0000\u0000In this work, we demonstrate isotropic ALE of ZnO on a regular array of vertical nanowires, using the alternated doses of O2 plasma and acetylacetone (Hacac). A linear ZnO thickness decrease with increasing number of cycles was measured by in-situ spectroscopic ellipsometry, and saturation behavior was demonstrated for both Hacac and O2 plasma, at 250 oC. The etch rates per cycle were found to increase from 0.5 to 1.3 A/cycle with process temperature increasing from 100 to 250 oC. Transmission electron microscopy (TEM) studies conducted on ZnO-coated nanowires before and after ALE proved the isotropic character of the process. Moreover, the ALE process produced no surface damage as concluded from high resolution TEM inspection. In-situ infrared spectroscopy measurements were conducted to elucidate the mechanism underlying self-limited etching. Based on these measurements, a preliminary reaction mechanism is proposed, in which Zn(acac)2 is assumed to be the etching product and persisting acac-species on the ZnO surface provide the self-limiting character. Finally, a high etch selectivity over SiO2 and HfO2, and the possibility to extend the process to other oxides such as Al2O3 are also demonstrated. \u0000\u0000We believe that this plasma-based ALE process represents a valuable addition to the ALE toolbox and opens-up new possibilities for using plasma-processing to achieve isotropic etch profiles. Furthermore, similar approaches can be used to extend the process to other materials by tuning the plasma chemistry accordingly.","PeriodicalId":433139,"journal":{"name":"Advanced Etch Technology for Nanopatterning VIII","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2019-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130293143","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
D. Miles, R. McEntaffer, F. Grisé, C. Eichfeld, R. McCurdy
{"title":"Blazed x-ray reflection gratings using electron-beam lithography and ion milling (Conference Presentation)","authors":"D. Miles, R. McEntaffer, F. Grisé, C. Eichfeld, R. McCurdy","doi":"10.1117/12.2514857","DOIUrl":"https://doi.org/10.1117/12.2514857","url":null,"abstract":"Astronomical X-ray diffraction gratings are a key technology under development for current and future NASA missions. X-ray reflection gratings, developed at Penn State University, have recently demonstrated both leading diffraction efficiency and high spectral resolving power. However, recent results are the result of different fabrication techniques and a single technique has not yet been developed to yield a grating that satisfies both the diffraction efficiency and resolving power required by future missions. Here we seek to leverage exiting electron-beam lithographic techniques to produce a grating with groove groove pattern capable of high resolving power. We then introduce new ion-milling techniques to create custom groove profiles capable of high diffraction efficiency. The goal is to produce a radial groove pattern with precisely blazed facets that are customizable based on ion mill input parameters. The process should be insensitive to groove density (ranging from ~150 nm to 400+ nm), facet size, and desired facet angle. Initial efforts in this study have concentrated on constraining various parameters in ion milling to fully characterize the effect of each parameter on the grating groove profile. We present here initial results and discuss experimental verification and future work.","PeriodicalId":433139,"journal":{"name":"Advanced Etch Technology for Nanopatterning VIII","volume":"7 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2019-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116847448","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}