{"title":"A Numerical Method for Fast Filtering Antenna Analysis with Arbitrary Reference Impedances at Millimeter-wave Frequencies","authors":"Teng-Yuan Chang, H. Chou, Chia-Hung Chang","doi":"10.1109/RFIT52905.2021.9565312","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565312","url":null,"abstract":"In this research, a numerical method is presented for the design of filtering antennas. It aims to quickly verify filter characteristics of the Q factor, bandpass bandwidth, and order, which are integrated into the antenna architecture in a cascading fashion. The developed software tool can be used to reduce the design cycle time of antennas and also predict the filtering performance. It applies to problems of filtering antenna design using cascaded connections of multiple n-order filters. This method is validated and adopted to design a filtering antenna at 110 GHz, where the antenna is integrated with two three-order bandpass filters. The simulated result shows a broad frequency bandwidth with good filtering effects.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"29 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121118536","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"94 GHz CRLH Substrate-Integrated-Waveguide (SIW) Slot Antenna Array Using Silicon-Based IPD","authors":"Chiao-Yun Hsiao, C. Wu, C. Kuo","doi":"10.1109/RFIT52905.2021.9565246","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565246","url":null,"abstract":"This paper presents an on-chip 94 GHz composite right/left-handed (CRLH) substrate-integrated-waveguide (SIW) slot antenna array using silicon-based integrated passive device (IPD) technology. By harnessing the negative and zeroth modes of CRLH SIW resonators, the proposed silicon-based IPD antenna can demonstrate a return loss of 13.8 dB at 94 GHz, whereas the 10-dB return loss bandwidth is 6.6 GHz in the measurement. Moreover, beam steering characteristics at 94 GHz are also verified by the proposed two-element CRLH SIW array prototype excited with different progressive phases.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"3 Dermatol Sect 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125875718","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Design of Quasi-Elliptic Bandpass Filters Based on Short-Circuited Coupled-Line Stubs","authors":"Shih-Fong Chao","doi":"10.1109/RFIT52905.2021.9565242","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565242","url":null,"abstract":"This paper presents a new method to design quasi-elliptic bandpass filters (BPFs). A short-circuited coupled-line stub (SCCLS) is proposed to serve as a resonator of a BPF and also generate a pair of symmetrical transmission zeros (TZs) at the stopband frequencies. An equivalent circuit model of the SCCLS is derived to facilitate the design procedure. To demonstrate an example, a 3rd-order quasi-elliptic BPF is designed and fabricated. The implemented quasi-elliptic BPF is based on a coupled-resonator filer design, except a connected coupling mechanism is introduced to incorporate the SCCLS into a BPF. The measured results agree well with the simulations thus successfully verify the design concept.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"6 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123898729","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"High Power Wide-Band GaN Amplifiers: Industrial Design and Challenges","authors":"K. Samanta","doi":"10.1109/RFIT52905.2021.9565203","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565203","url":null,"abstract":"Many advanced industrial applications demand high power amplifiers (HPAs) with ever greater power across a wideband, within a small size, and with high reliability and long life. In addition, for a wideband GaN HPA, withstanding high output mismatch, overcoming inherent limitations, efficient thermal management, and achieving linearization and modulation requirements across a wide-bandwidth raise many design challenges. This paper presents the practical design and assembling difficulties with industrial solutions, and the development of very high power GaN PAs with decade bandwidth, and delivering high CW (P1dB) power to 1 kW (close to Psat), overcoming the inherent limitations of GaN devices.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"72 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114528420","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A 3.5-GHz 2-W Power Amplifier in GaN HEMT Technology","authors":"Lung-Yi Chen, Jia‐Shiang Fu","doi":"10.1109/RFIT52905.2021.9565317","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565317","url":null,"abstract":"A power amplifier (PA) is designed at 3.5 GHz for 5G small-cell base station applications. The proposed PA is implemented in WIN $0.25- mu m$ GaN HEMT technology. The chip area is $1 times 1 mm 2$. Measurement results show that, from 3.3 to 3.8 GHz, the input return loss and gain of the PA are greater than 10.2 dB and 12.6 dB, respectively. At 3.5 GHz, the measured $OP _{1dB}$ and the corresponding PAE are 33 dBm (2 W) and 44%, respectively.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"41 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121613356","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"High-Output Current Gallium Nitride Transconductance Amplifier","authors":"A. L. T. Costa, C. Saavedra","doi":"10.1109/RFIT52905.2021.9565283","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565283","url":null,"abstract":"In analog and microwave signal processing, transconductance amplifiers are used as building blocks for tunable filters, phase shifters, signal generation and other applications. These amplifiers are commonly known as operational transconductance amplifiers (OTAs) and deliver output currents in the milliampere range. Meanwhile, a different type of application space exists for transconductance amplifiers (TCAs) that yield output currents from Amperes to tens Amperes. These TCAs are systems onto themselves and are used for monitoring of power flow in electricity distribution networks, calibration of power transformers, power meters and high-current clamp meters among other applications. At present, commercial TCAs deliver up to 100 A of current from dc to 1 MHz to a shunt load. A standard TCA design uses a parallel arrangement smaller silicon-based TCA cells, each delivering 5 A of current. In this work, we report on the design, fabrication and measurement of a 25 MHz gallium nitride (GaN) transconductance amplifier (TCA) cell that delivers up to 6.45 A of ac current (12.9 A, peak-to-peak) to a shunt load. The TCA accepts input voltage signals of up to 3 V amplitude and yields a maximum transconductance gain of 2.15 Siemens. The TCA features a Class AB output stage driven by signal conditioning circuitry that converts a single-ended input to a differential signal. The gate bias for the dc-coupled GaN devices is provided through the driver circuits. The output current flows through a high-precision sensing resistor and terminates in a 10 m$Omega$ load. The nominal dc power rating of the transistors is 35 Watts and this value is used to set the transistor dc bias voltages. For a target output current of 10 A peak-to-peak (5 A, peak), the VDS for each transistor is set to 7 V. Considering the basic case of a balanced TCA output of 0 V, then $V_{S1} = V_{D2}$ = 0 V for the GaN devices and therefore, VDD = 7 V and VSS = −7 V. The GaN transistors used in this work are packaged Wolfspeed CGH40035F power HEMT operating from a 28 V rail supply. The total harmonic distortion (THD) of the TCA was calculated from measured time-domain data. The worst-case THD is 7% over the 25 MHz band while the minimum is 1% at 10 MHz and 10 A peak-to-peak output current. Table I below compares the frequency response of the Queen’s GaN TCA cell with industrial designs.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"203 3-4","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114027262","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A 210.4-dBc/Hz FoMT 67.9% Tuning Range LC-VCO IC with a Single Analog Voltage-Controlled Novel Varactor in 40-nm CMOS SOI","authors":"Mengchu Fang, Akihiko Kumura, T. Yoshimasu","doi":"10.1109/RFIT52905.2021.9565258","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565258","url":null,"abstract":"This paper presents a wideband VCO IC with a single analog voltage-controlled novel varactor. The novel varactor which consists of two parallel Inversion-MOS (IMOS)-based varactors and a variable resistor is tuned by a single analog voltage. Two IMOS-based varactors are biased at different gate-to-source voltages so that KVCO can be improved while the variable resistance contributes to the extension of the tuning range. The proposed VCO IC is designed, fabricated, and fully evaluated on-wafer in 40-nm CMOS SOI. The proposed wideband VCO IC delivers a tuning range of 67.9% from 3.20 to 6.49 GHz and has exhibited an excellent measured FoMT of 210.4 dBc/Hz under the minimum power consumption of only 0.35 mW.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"13 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126434875","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A 19-GHz 5-Bit Switch-Type Phase Shifter Design Using Phase Compensation Techniques","authors":"You-Jen Liang, Kun-Chan Chiang, Yi-Hsien Lin, Hamed Alsuraisry, Jeng‐Han Tsai, Tian-Wei Huang","doi":"10.1109/RFIT52905.2021.9565300","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565300","url":null,"abstract":"A 19-GHz 5-bit switch-type phase shifter (STPS) using 180-nm CMOS technology is presented. In this paper, the reverse-direction phase compensation technique is used to make the final results closer to the design goal. The measured insertion loss for all 32 states is 13 ± 1 dB at 19 GHz. The phase shifter achieves a RMS phase error of 3.7° and a RMS amplitude error of 0.5 dB at 19 GHz, which are improved from initial phase error of 8.2° and amplitude error of 0.82 dB, respectively.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115763555","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A 28/39 GHz Dual-Band Power Amplifier Using Optimal Matching Contour in GaAs pHEMT","authors":"B. Huang, Z. Fu, Kun-You Lin","doi":"10.1109/RFIT52905.2021.9565282","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565282","url":null,"abstract":"In this paper, a dual-band power amplifier (PA) fabricated in 0.15-μm GaAs pHEMT process is presented. The concept of the optimal matching contour is used in the matching network design to minimize the loss in both operating frequency bands. Thus, this PA achieves good power performance in both frequency bands. The measured results of small-signal gain are 20/12 dB at 28/39 GHz, respectively. The saturated output power (Psat) is 21.9/22.7 dBm, the peak power-added efficiency (PAEmax) is 28.9/32.6%, and the OP1dB and corresponding PAE (PAE1dB) are 21.8/22.6 dBm and 28/32% at 28/39 GHz, respectively.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"27 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131845913","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S.-D. Yin, Wenyuan Zhang, Wenfei Hu, Zhikai Wang, Ruitao Wang, Jian Zhang, Yan Wang
{"title":"An Efficient Reference-point Based Surrogate-assisted Multi-objective Differential Evolution for Analog/RF Circuit Synthesis","authors":"S.-D. Yin, Wenyuan Zhang, Wenfei Hu, Zhikai Wang, Ruitao Wang, Jian Zhang, Yan Wang","doi":"10.1109/RFIT52905.2021.9565309","DOIUrl":"https://doi.org/10.1109/RFIT52905.2021.9565309","url":null,"abstract":"In this paper, we propose an efficient reference-point based surrogate-assisted multi-objective differential evolution algorithm for analog/RF circuit synthesis, which aims to greatly reduce simulation time while maintaining accuracy. First, offspring are generated by differential evolution operator and polynomial mutation. Then we predict the offspring by Gaussian process. Finally, sort the offspring by modified reference-point based NSGA-III criterion, only the most promising one instead of multiple designs is able to be simulated by the circuit simulator. Experimental results on two real-world circuits show that compared with two state-of-the-art multi-objective evolutionary algorithms, our method can achieve up to 6X simulation time reduction without surrendering any accuracy.","PeriodicalId":406432,"journal":{"name":"2021 IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)","volume":"13 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130995913","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}