{"title":"Effect of Shallow Cryogenıc Heat Treatment on Metal Inert Gas Weldıng Zone of S 355 J2 Steel","authors":"Z. Özdemir","doi":"10.30811/jowt.v5i1.3888","DOIUrl":"https://doi.org/10.30811/jowt.v5i1.3888","url":null,"abstract":"Metal inert gas welding (MIG) is generally conducted in the pressure vessel industry due to its high quality and easy automation. S355 J2 steel is used widely in this industry for its proper welding properties. To carry out and obtain high melting efficiency for satisfactory mechanical properties according to welding parameters, sometimes heat treatment is applied to materials, but generally it is not common in welding industry. In this study the effect of conventional heat treatment and shallow cryogenic heat treatment effects to the mechanical properties of welding zone of S 355 J2 steel welded with MIG is investigated. The charpy impact tests have been carried out. The welding plate is prepared according to this purpose and it is cut for impact test samples 10 X 10 x 55 mm. Totally 30 samples are prepared for 5 processes. Process 1: 6 samples for without heat treatment. Process 2: 6 samples for normalization-quenching in water. Process 3: 6 samples for normalization-quenching-tempering. Process:4 6 samples for normalization-shallow cryogenic treatment. Process 5: 6 samples for normalization-shallow cryogenic treatment-tempering. Notch of impact test samples are prepared just in the middle of the welding zone (2 sample for each process) , HAZ (2 sample for each process) and basemetal (2 sample for each process). The hardness values are taken from base metal, heat affected zone and welding area respectively. Hardness values and impact test results are compared. As a result, generally, it has been observed that shallow cryogenic heat treatment have a remarkable effect on toughness, despite a little decrease in hardness. The toughness of welding zone is increased approximately %40 and HAZ % 5 after cryogenic heat treatment. The hardness of WZ is increased approximately % 5 after cryogenic heat treatment, no significant change is observed in HAZ.","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"198 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133036040","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
E. Widodo, D. Anggara, Moch. Karim Al Amin, M. I. Al Jawwad
{"title":"Hardness Analysis of Aluminium 5083 A-TIG Welding Due to The Effect of Active Flux and Current","authors":"E. Widodo, D. Anggara, Moch. Karim Al Amin, M. I. Al Jawwad","doi":"10.30811/jowt.v5i1.3886","DOIUrl":"https://doi.org/10.30811/jowt.v5i1.3886","url":null,"abstract":"Aluminium allow has been widely used recently due to their high strength to mass ratio, good formability and high corrosion resistance have a wide range of applications in aerospace, ship-building and railway industries. The 5083 series aluminum is the most widely used due to good strength and corrosion resistance properties. Tungsten Inert Gas Welding (TIG welding) is the most common welding method for aluminum alloys. This research was conducted A-TIG welding on 150 x 100 x 8 mm of 5083 aluminium and added by oxide powder (MgCl2 and TiO2) as active flux and various of current consist of 100, 130, and 160 A. The result of this research was obtained that the deepest penetration was 4.94 mm with TiO2 active flux and the current of 160 A, the highest hardness came from weld metal which using MgCl2 as an active flux with 100 A of current with 69.80 HVN. The hardness was increased by adding magnesium due to effect of it could be increased grain coarse. The lowest hardness was on weld metal with TiO2 active flux with 160 A of current due to the maximum heat input which decreased the hardness The recrystallization was occurred due to increase of heat input, so did the grain growth. The coarse grain which caused the decreasing of hardness was affected by the increase of heat input.","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"13 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"120976063","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Corrosion Rate Analysis on SA 240 TP 904L Material Experience Multiple Repair","authors":"Muhammad Ari, D. Anggara, Amar Sastra Adi","doi":"10.30811/jowt.v5i1.4019","DOIUrl":"https://doi.org/10.30811/jowt.v5i1.4019","url":null,"abstract":"Weld imperfections are likely to arise during any welding process. Due to the enormous number of joints that could result in weld defects, welding process faults could happen. Repair procedures are required to address welding defects. Multiple repairs are required if welding mistakes are made repeatedly. The duplex material used in this study is SA 240 TP 904L. By altering the repair procedure treatment 1x, 3x, 5x, and without repair, the welding process is carried out utilizing the SMAW method and E309L filler. Microstructure testing, ferrite content testing, and 3-electrode cell corrosion are the test techniques used. The relationship between the corrosion rate and the amount of ferrite content was deduced from the test data. The corrosion rate increases as the ferrite content rises due to several repairs.","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"280 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126879164","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Influence of Weld Current and Weld Time on the Push Test, Nugget and Penetration Depth of Steel Plate SPFC590 with Weld T-Nut M10","authors":"Ardhi Alfarizzi Tanjung, B. Budiarto, Surjo Abadi","doi":"10.30811/jowt.v5i1.3651","DOIUrl":"https://doi.org/10.30811/jowt.v5i1.3651","url":null,"abstract":"This study describes the effect of parameter current and weld time, welding using materials plate steels SPFC590 t1.2 and Weld T-Nut M10 with media seated spot welding machines brand Dagensha 50 kVA. This test is to analyze push test, nugget, and penetration depth spot welding against the engineering standard of PT HMC (Hyundai Motor Company). In this research, the researcher used the factorial experimental design method to provide a test lay out formulation, know the optimal conditions for setting parameters, and determines the performance effect of setting the parameters such as push test, nugget, and penetration depth spot welding. Test results push test between plate steels SPFC590 t1.2 and Weld T-Nut M10 the largest was 17.7 kN and the smallest was 15.4 kN the test results have passed the results of the engineering standard 6.5 kN. The test results on the nuggets the longer the melt occurs the wider the growth of the melt, and after part at room temperature the melt zone will become nuggets for the average nugget test results is 5.6 mm and has passed the engineering standard results. While the penetration test results the longer the welding time the deeper the penetration depth. The conclusion from this research, among others, is that the parameters of welding time and current strength can affect the results of the Nugget size and penetration depth of Spot Welding, but can reduce the strength of the push test besides that the less the remaining plate that is not exposed to penetration the smaller the push test strength, and the less the penetration depth the smaller the push test strength and the higher the current strength the greater the size of the nugget","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"43 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128331305","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Analysis of the effect of current on tensile strength of aisi 1050 material in the SMAW welding process","authors":"Aris Mauliza, Usman Usman","doi":"10.30811/jowt.v4i1.2996","DOIUrl":"https://doi.org/10.30811/jowt.v4i1.2996","url":null,"abstract":"Shield Metal Arc Welding (SMAW) which is also called Electric Arc Welding is a welding process that uses heat to melt the base material or base metal and electrodes (fill material). Meanwhile, at the processing stage, the appropriate current strength will be selected to the working position. The purpose of this study was to determine the effect of welding current on the mechanical strength of AISI 1050 medium carbon steel. The currents used were 100 A, 125 A and 150 A. After doing research, SMAW welding on AISI 1050 medium carbon steel with variations in current affects the value tensile strength, stress and strain that occur after welding. As the results obtained are for welding currents with a current of 150 A having the highest tensile strength of 74.36 kgf/mm2, while for a current of 100 A having a tensile strength of 72.94 kgf/mm2, while the lowest value is at a current of 125 A which has a tensile strength of 51.45 kgf/mm2. , while the strain that occurs at a current of 100 A is 10.13%, while at a current of 125 A the strain that occurs is 5.27%, and at a current of 150 A that is 9.92%","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"32 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130464982","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Hot tapping process analysis on gas distribution pipes online service using Shielded Metal Arc Welding","authors":"B. Prasojo, Yunan Sadli Nasution","doi":"10.30811/jowt.v4i1","DOIUrl":"https://doi.org/10.30811/jowt.v4i1","url":null,"abstract":"In a piping system makes it possible to add branching into an existing piping system. In this research will discuss about installation 12 \" branch pipe in to 16” existing pipe. The system should be installed without interrupting the operation of the pipeline to avoid huge losses. Hot-tapping is a technology that works to create branching on the online service pipe condition. Calculation and analysis of the results to ensure the process of hot-tapping absolutely safe to operate. parameters that must be considered include the heat input, the operating pressure during welding hot-tapping process with Shielded Metal Arc Welding, stress that occurs at the branching system. Analysis on split tees must be done because of stress that occurs due to the welding process and the reduction in thickness. Analysis on the plumbing system must be done because of a new branching thus causing new stress. The results of the analysis on split tees and the pipe system is used as a reference-making procedures for implementing hot-tapping. Maximum stress that occurs in the pipes during hot-tapping process is the welding area (22.828 psi). The welding process causes melting partial in the metal pipe so, during welding process (hot-tapping) working pressure should be reduced by 25.27%. The condition of the fluid in the existing pipeline still safe because liquefaction as a result of the welding process does not penetrate to the inner pipe. The new design results in branch pipe eligible to fabricated because stress that occurs is still below the allowable stress values","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"8 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123403924","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The Effect of Heat Input on the Tensile Strength and Toughness of welded SS400 Materials by SMAW","authors":"Syukran Syukran, Alvi Syahri, Adi Saputra Ismy","doi":"10.30811/jowt.v5i1.3508","DOIUrl":"https://doi.org/10.30811/jowt.v5i1.3508","url":null,"abstract":"Joint materials using welding require the correct stages, starting from the design stage to the processing stage. The design stage starts from the selection of the type of welding, to the selection of the seam angle used. Meanwhile, at the processing stage, the current strength will be selected according to the processing position. The purpose of this study was to determine the effect of welding heat input on the mechanical strength of SS-400 steel in SMAW welding. In this study the material used was SS-400 with current variations of 90 A and 100 A. The results showed that the welding current affected the tensile strength and toughness of the material. The welding current of 100 A has the highest tensile strength and toughness, and then 90 A which has the lowest tensile strength and toughness, while the strain that occurs at current 90A is 13.53%, and the strain that occurs at current 100 A is 12.07%.","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"25 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127815094","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The effect of weld groove variations on the toughness of welding joints of AISI 1050 material","authors":"Z. Purba, Samsul Bahri","doi":"10.30811/jowt.v4i1.2998","DOIUrl":"https://doi.org/10.30811/jowt.v4i1.2998","url":null,"abstract":"SMAW (Shielded Metal Arc Welding) welding is a metal joining process that uses heat energy to melt the workpiece and electrode (fill material). The flux material used for type E7016, a low hydrogen electrode wire typically used for welding heavy-duty plates and structures. Its use is for welding medium carbon steel, bridges, ships and machinery. The result of welding electrode E7016 is very smooth, deep penetration, crack resistant, ductile, good weld appearance and stable arc, the material used in the SMAW welding process is AISI 1050 steel. While AISI 1050 steel is steel that has a carbon content of 0.50 % so that it is classified as medium carbon steel. This steel is widely used in the market because it has many advantages, one of which is as an automotive component. This steel has the characteristics of good machinability, good wear resistance and medium mechanical properties. This study aims to determine the shock strength (impact) and the difference in the time of making weld grooves on SMAW welding results on AISI 1050 steel with variations of Double Bevel and Double V Groove grooves. In testing in the Weld Metal area with a current used of 110 Ampere. From the tests that have been carried out, it is known that the value of the highest impact strength is in the Double Bevel groove which has a value of 1.91 Joule/mm2, for the manufacture of welded grooves where the Double Bevel time is shorter than Double V Groove, so the time produced by Double Bevel which is 3.44 minutes/second.","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"48 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-06-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122048362","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Analysis of Hydro Test Pressure Variations on A106 Grade B Carbon Steel Pipe Welded Joints with Welding Repair Method","authors":"Riswan E.W. Susanto, Kris Witono","doi":"10.30811/jowt.v4i2.3556","DOIUrl":"https://doi.org/10.30811/jowt.v4i2.3556","url":null,"abstract":"Transportation of oil and gas through oil refinery pipelines is faced with problems, including corrosion problems. Corrosion is a natural phenomenon that occurs in metal materials, where corrosion is a process of material damage due to chemical or electrochemical reactions with its environment. The purpose of this study is the results of the analysis of HydroTest pressure variations on the Welding Joints of Carbon Steel Pipes (carbon steel) A106 Gr.B. In the study did not discuss the occurrence of corrosion and other tests, while the welding process in detail was shown in WPS. This experimental research method uses the Welding Repair Method on welded joints according to the ASME IX, ASME B31.3 standard. The research material is A106 GR carbon steel pipe. B is in the form of a U Tube Seal Deck that has undergone corrosion and damage, where later the fabrication process (pipe repair) especially welding (using SMAW and GTAW) has been determined in PQR and WPS (WPS / CS / EM / ASME / WPxxx). The focus of this research is on stage 9 (hydro testing stage) of the Welding Repair method. Free variables in pressures of 240 Psi, 435 Psi, 690 Psi, and 910 Psi, which have been planned based on the thickness and length of the Pipe joint. Variable fixed temperature test Hydrotest 28OC, holding time holding time (pressurizing) 10 minutes and holding time peak 60 minutes before (depressurizing). The results were obtained that the pressure change was divided into two stages, pressurizing with the highest pressure of 915 Psi is the 4th pressure variation this was obtained from the test observation that there were no leaks in the welded joints and pipe materials in accordance with the acceptance criteria. While the second stage is (depressurizing) with a decrease in pressure or called realese, where successively realese 100%, 75%, 50%, 25%, and 0% at pressures of 915 Psi, 690 Psi, 435 Psi, 240 Psi, 0 Psi with the results of no leakage and observation test results in accordance with the acceptance criteria. So it can be concluded that the welded joints of carbon steel pipes tested using hydrotest, no deformation occurs, there is no change in shape and there are no leaks in the welded joint layer of A106 Gr.B carbon steel pipe","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"98 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-12-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124954192","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Hardness Analysis of Weld Metal Electrode Low Hydrogen Potassium E7016 and E7018","authors":"Syukran Syukran, Azwinur Azwinur","doi":"10.30811/jowt.v4i2.3492","DOIUrl":"https://doi.org/10.30811/jowt.v4i2.3492","url":null,"abstract":"Electrodes for the Manual Metal Arc (MMA) welding process or welding electrodes are classified based on the type of coating which is informed by the last digit code of the electrode. Electrodes E7016 and E7018 are basic types of electrodes with a Low Hydrogen Potassium coating type which are widely used in welding heavy construction equipment and piping. This electrode has a minimum tensile value of 70 ksi (480 MPa) with a carbon content of 0.07% for E7018 and 0.08% for E7016. The difference in carbon content in the composition of the electrode will determine the hardness value of the resulting weld. In use in the field these two electrodes are often recommended and can even be exchanged according to the assumption that the minimum tensile value is relatively the same between the two electrodes. However, due to the difference in carbon content, it will affect the hardness of the weld (weld metal) after welding. Many studies have been carried out to determine the mechanical properties of the welded joints using these electrodes, but research on the specific mechanical properties of the welds of the two electrodes is very rarely carried out. The test method is carried out by making 2 test specimens each for currents of 80A, 100A, and 120A using E7016 and E7018 electrodes with a diameter of 3.2mm. The material used is SA.36. The hardness test was carried out using the Rockwell-C (HRC) method. The test results show that the hardness value of the basic low hydrogen potassium electrode E7018 has a higher hardness value than E7016 for the same current. At currents of 80A, 100A, and 120A, there was an increase in the hardness of the E7018 weld metal against E7016 by 2.0% each; 9.8%; and 6.7%. The highest hardness value is found at 80A of 42.3HRC for the E7018 electrode, and 41.5 HRC for the E7016 electrode. In E7016 the increase in current causes a decrease in hardness level of 8.2% from 80A to 100A; 12.3% from 100A to 120A. In E7018 the increase in current causes a 1.2% decrease in hardness from 80A to 100A; 14.7% from 100A to 120A","PeriodicalId":397972,"journal":{"name":"Journal of Welding Technology","volume":"6 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-12-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115197391","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}