{"title":"Study on Implementation of Lean Six Sigma in Hospital Auxiliary Ship Block Construction Process","authors":"Muhammad Rizki Kurniawan, R. Rochmoeljati","doi":"10.14710/kapal.v19i3.46155","DOIUrl":"https://doi.org/10.14710/kapal.v19i3.46155","url":null,"abstract":"During the pandemic, transportation is needed to support the evacuation of patients through waterways; therefore, PT PAL Indonesia (Persero) has created a Hospital Auxiliary Ship project. In building a quality Hospital Auxiliary ship project, productivity is needed so the project can be completed properly. However, there are problems with the punctuality of completing the ship block construction with a total lead time of 19200 minutes and found the block quality is not up to standards like Surface Porosity, Former Stopper, Arc Strike, and Low Bead defects that require a rework process and cause long cycle times. This study aims to reduce the lead time value and minimize waste or activities that are not value-added using the lean six sigma method with stages (DMAIC). From the results of the study, it was found that the identification of the Process Activity Mapping (PAM) design, which resulted in the highest waste rating, namely 16.94% defect, with CTQ-4, lean six sigma value of 3.055 sigma and DPMO value of 59917 which was included in the excellent category for the industry average. The factors causing the problem were identified with Pareto diagrams and causal diagrams to determine the dominant type of defect and the causes of wastage of defects; there are four factors, namely material, human, machine, and environment. Recommendations for the improvement of waste are through material inspection, operator training, reworking defective blocks, and minimizing non-value-added activities. With the design of process activity mapping (PAM) and value stream mapping, the efficiency of ship block construction can increase from 67.81% to 74.06%.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"35 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-08-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121204937","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
A. I. Wulandari, R. J. Ikhwani, S. Suardi, Ratna Septati Yani, Andi Nadia Himaya, A. Alamsyah
{"title":"Collision Analysis of a Self Propelled Oil Barge’s (SPOB) Using Finite Element Method","authors":"A. I. Wulandari, R. J. Ikhwani, S. Suardi, Ratna Septati Yani, Andi Nadia Himaya, A. Alamsyah","doi":"10.14710/kapal.v19i2.45417","DOIUrl":"https://doi.org/10.14710/kapal.v19i2.45417","url":null,"abstract":"Impact is a collision between two objects of force in a short time of period. Research on hull impact SPOB 3500 DWT using element method up to Ansys Explicit Dynamics software. In this study, two variations models were used, when impact where the jetty is not equipped with fenders and jetty equipped with fenders. Value of plate thickness is 10 mm, and with a speed variation of 0.5 m/s 1 m/s and 2 m/s. Using element-based applications to determine damage based on deformation values on the SPOB 3500 DWT body when crashing jetty and hull damage after jetty that is not equipped with fenders and fenders equipped at speed variations. . The force values that have been calculated with speeds of 0.5 m/s, 1m/s and 2m/s are 3.52 MN, 7.04 MN, and 14.07 MN, respectively. With the deformation values in the model of the ship hitting a jetty that is not equipped with fenders which are calculated at a speed of 0.5 m/s, 1m/s and 2m/s, respectively, they are 0.53011 mm, 1.0594 mm, and 2.1184 mm. And the value of deformation on the model of the ship hitting a jetty equipped with fenders which is calculated at a speed of 0.5 m/s, 1m/s and 2m/s, respectively, is 0.36511 mm, 0.7357 mm, and 1.4939 mm.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"31 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-07-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121222849","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
A. Muhammad, A. Thariq, Zulkifli Yusuf, H. Yudo, M. Yasir
{"title":"The Selection of Propeller and Primary Engine Matching of A 30 GT Fishing Vessel (Case Study KM Inka Mina 759)","authors":"A. Muhammad, A. Thariq, Zulkifli Yusuf, H. Yudo, M. Yasir","doi":"10.14710/kapal.v19i2.46070","DOIUrl":"https://doi.org/10.14710/kapal.v19i2.46070","url":null,"abstract":"Reducing fuel consumption and carbon emissions in the development of ship propulsion systems following the required Energy Efficiency Design Index (EEDI) has become a concern for the fishing industry as determined by the International Maritime Organization (IMO). This study analyzes the suitability of using a 30 GT fishing vessel propeller and propulsion engine for optimum efficiency. The analysis focuses on developing a propulsion system selection model, studying the characteristics of the ship's resistance, loading propellers, and selecting the appropriate engine. The propeller-engine matching procedure predicts the propeller and engine suitability. Furthermore, the Analytic Hierarchy Process (AHP) method determines the suitability level for the propeller and diesel engine. The results showed the highest level of suitability for the Yanmar 6CH-HHTEC engine versus the A.30X34 type propeller with 31.7%. Then the Deutz BF06M1013MC engine versus the B.30X28 propeller type, the Yuchai YC6A170C engine versus the B30X28 propeller type, and the Volvo D7ATA engine versus the B30X28 propeller type with percentages of 26.6%, 26.4%, and 15.3%, respectively. The high level of SP2 selection is due to the propulsion system having minimal noise levels, dimensions, and engine weight but having maximum power.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"4 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-07-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123817534","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Comparison of the Ultimate Strength with and without Hatch Opening Subjected to Longitudinal Bending","authors":"Indah Melati Suci, M. Z. Muis Alie, G. Sitepu","doi":"10.14710/kapal.v19i2.45097","DOIUrl":"https://doi.org/10.14710/kapal.v19i2.45097","url":null,"abstract":"The hatch opening has function to enter the load into the cargo hold. One of the ship type like this is Bulk Carrier. The hatch opening must be designed in suitable way because its influence to the ultimate strength since the hull girder under longitudinal bending moment. The application of the hatch opening on the ship’s deck should be considered for the ship design critreria. The objective of the present study is to analyze the ultimate strength with and without hatch opening subjected to longitudinal bending moment. The cross section of box girder is used to analyze the effect of hatch opening to the ultimate strength. This cross section of box girder is adopted for simple calculation. The application of Multiple Point Constrained (MPC) is adopted to analyze the box girder under longitudinal bending moment. The cross section of box girder is assumed remained plane during progressive collapse. The material such as density, yield strength, elastic modulus and poisson ratio are homogeneous. The type and dimensions of the stiffeners are also identic. The only one of the difference for the stiffener is number due to the hatch opening at the top of the box girder. It is found that the ultimate strength of the box girder with hatch opening is smaller than without opening one. ","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"11 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131222517","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Study of QR Code Technology Application for Monitoring Activity of Ship Planned Maintenance System","authors":"S. I. Wahidi, T. W. Pribadi, Hajid Mulya Rahman","doi":"10.14710/kapal.v19i2.45507","DOIUrl":"https://doi.org/10.14710/kapal.v19i2.45507","url":null,"abstract":"System and outfitting in a ship vary with different brands and treatment methods. These conditions can be an issue if the operator has undisclosed damages due to a lack of knowledge about the ship's maintenance records. An electronic planned maintenance system (ePMS) is a system that is currently used to collect the ship maintenance recorded data. However, the use of ePMS still has drawbacks. The appearance is less interactive, available information about the outfitting used in ships is limited, and the operator needs to search the outfitting manually with scrolling. This research aims to study the application of QR code technology for monitoring maintenance activities of ship systems and outfitting. This research was conducted based on field observation of ePMS, designing a QR code module for the ePMS application, developing algorithms, and creating programs for website and android based applications. In addition, trials of the application and calculation of the costs incurred for implementing the QR code method are also carried out. The distribution of questionnaires for practitioners accompanied the trial. Based on that, the implementation of QR code in ePMS can be applied, easy to use and facilitate the supervision of ship system and outfitting activities with a mean score of 4.39 or equivalent to strongly agree. The addition of the QR code module is costed IDR120,426,000.00, where the process of recognizing and searching for ship systems and outfitting to view maintenance plans and maintenance history on the ePMS application is enough by scanning a QR code.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"39 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132540008","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"The Effect of Heat Input on Welding Combination of GTAW and SMAW SA537 Material on Mechanical Properties and Microstructure","authors":"T. Tarmizi, Nabil Aga Hananda, Irfan Irfan","doi":"10.14710/kapal.v19i2.45028","DOIUrl":"https://doi.org/10.14710/kapal.v19i2.45028","url":null,"abstract":"The combination of GTAW (Gas Tungsten Arc Welding) and SMAW (Shield Metal Arc Welding) processes on SA537 Class 2 carbon steel using variations of heat input is the main choice to get the best quality welded joints. This research aims to joint SA537 Class 2 material using the GTAW and SMAW process with heat input variations to get the best joint and determine the joint results mechanical properties and microstructure analysis. The experimental method uses a combination of GTAW and SMAW processes with a single V butt joint design, groove angle of 60o, root face 2 mm and root gap of 4 mm as many as 7 passes, and variations in heat input of 2.5 kJ/mm, 2.8 kJ/mm and 3.2 kJ/mm. According to ASME section IX, the mechanical testing results showed that the specimen with a heat input of 2.8 kJ/mm gave optimum results with the highest tensile strength of 480 MPa compared to the other two specimens, and there were no cracks when tested for bending The higher the heat input, the greater the decrease in the percentage of ferrite. Using a heat input of 2.8 kJ/mm in this study provides a weld result with better mechanical properties and microstructure than the use of heat input of 2.5 kJ/mm and 3.2 kJ/mm.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"6 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-06-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128877444","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Fire-safe Distance Between Ro-Ro Space Openings and Life-saving Appliances","authors":"Pierrick Mindykowski","doi":"10.14710/kapal.v19i2.44753","DOIUrl":"https://doi.org/10.14710/kapal.v19i2.44753","url":null,"abstract":"As part of the FIRESAFE II project commissioned by the European Maritime Safety Agency a study was performed to determine a safe distance between side openings and Life-Saving Appliances (LSA) in ro-ro spaces to keep them available and usable for evacuation. The study utilised analytical calculations and CFD simulations. Two exclusion zones, where LSA should not be placed, were defined. The first zone relates to LSA within an embarkation station and includes the full vertical side of the ship, 6 metres forward and aft the opening. The second zone, without presence of passengers, consisted of the exclusion zone extending 6 metres around the opening. The results presented in the paper have been implemented in the International Maritime Organization interim guidelines for minimising the incidence and consequence of fires in ro-ro spaces and special category spaces of new and existing ro-ro passenger ships.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-05-19","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131177759","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Modification of Surface Buoy to Preserve Under Water Habitat in Raja Ampat","authors":"O. Mursid, N. Huda, H. Nubli","doi":"10.14710/kapal.v19i1.41792","DOIUrl":"https://doi.org/10.14710/kapal.v19i1.41792","url":null,"abstract":"The ecosystem of the seabed is threatened by anchoring operations. Modifications were required toreduce the damage to seabed biodiversity. A laid chain on a mooring system is one of the causes ofdamage to the seabed environment. In this paper, six mooring configurations are studied to achieve theoptimum configuration on the moored vessel KM Putri Mandiri based on the chain length laid, thetension chain, and the vessel offset. The benefit of this study is to preserve the underwater habitat in RajaAmpat. The quantities and buoyancy capacities of the surface buoy are used as variable designs in thisstudy. Ansys Aqwa software is utilized to calculate mooring systems with environmental conditions,water depth 15 m, wave height 1.5 m, wind velocity 15 knots, and sea current speed of 1 m/s. The resultsshowed that more surface buoys caused lower laid chain length and closer ship offset but increasedtension chain. Configuration E, which consists of 3 surface buoys, was the optimum configuration for thisstudy.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"130 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-03-14","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131466501","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Analysis of Performance, Emission, Noise and Vibration on Single Cylinder Diesel Engine After Installing Dual Fuel Converter-Kit Based on ECU","authors":"A. Iswantoro, I. Ariana, Muhammad Syuhri","doi":"10.14710/kapal.v19i1.44126","DOIUrl":"https://doi.org/10.14710/kapal.v19i1.44126","url":null,"abstract":"Now the demand for fuel oil has increased, this can cause fuel oil reserves to be depleted. To reduce the use of fuel oil, alternative energy is needed. One alternative energy that can be used to reduce fuel oil consumption is LPG (Liquid Petroleum Gas). The use of alternative fuels for LPG in diesel engines is done by converting diesel engines into dual fuel. This research aims to determine the effect of using dual fuel that are LPG-Diesel fuel on engine performance including power, torque, fuel consumption, emissions, vibration and noise. The research was conducted using a Yanmar TF 85 MH engine at 2000 RPM engine speed with variations in loading of 1000, 1500, 2000, 2500, and 3000 watts, and dual fuel with variations in injector openings of 3ms, 4ms, 5ms. Based on the research results, the use of LPG in dual fuel system with installing ECU (Electronic Control Unit) converter-kit, can replace diesel fuel oil consumption up to 93%. In the use of dual fuel there is an average decrease in power and torque of up to 1.95% if using only diesel fuel have average power up to 2.32 kW and torque up to 11.09 Nm. When using dual fuel there is a decrease in specific fuel oil consumption by up to 44% when using only diesel fuel have average fuel oil consumption up to 414.15 g/kWh. The maximum NOx emission produced is 1.83 g/kWh for a 3ms gas injector opening, 1.48 g/kWh for a 4ms gas injector opening, and 1.81 g/kWh for a 5ms injector opening. The maximum vibration generated is 33.2 m/s² for a 3ms injector opening, 31.4 m/s² for a 4ms injector opening, 27.46 m/s² for a 5ms injector opening, and when used only Diesel Fuel is 32.8 m/s2. The maximum noise generated is 92.33 dBA for 3ms injector opening, 92.43 dBA for 4ms injector aperture, 93.20 dBa for 5ms injector aperture, and 91.73 dBa when using diesel oil only.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"42 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-03-11","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122440565","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Riska Arum Dona Kusnadi Putri, T. Yulianto, R. C. Ariesta, M. N. Misbah
{"title":"Influence of Stress Concentration Factor due to Scallop Form on the Wrang Plate Stucture","authors":"Riska Arum Dona Kusnadi Putri, T. Yulianto, R. C. Ariesta, M. N. Misbah","doi":"10.14710/kapal.v19i1.43344","DOIUrl":"https://doi.org/10.14710/kapal.v19i1.43344","url":null,"abstract":"The presence of opening in construction is unavoidable for the purpose of reducing stress. A small opening at the construction serves as access to continue the installed construction that runs through the web or girder. However, the presence of the hole also creates an unavoidable problem, the concentration of stress in the area around the hole that will gradually reduce the strength of the ship's construction. Stress concentration occurs due to changes in geometry, causing the flow of stress initially uniformly driven and following the existing geometry. This analysis aims to determine the value of stress concentration factors on the wrang plate due to variations in the shape of scallops. The research method is performed numerically using finite element analysis to find variations in the model with the lowest stress concentration factor. This variation consists of 3 different scallops models with 2 load, drag and press conditions. The values of stress concentration factors are grouped into 3 modes according to mechanical fractures in press loading conditions. Based on the analysis of panel models with compressed loads, it can be seen that model III has the smallest stress concentration factor value in case modes I and III but for mode II the value of the smallest stress concentration factor in model II.","PeriodicalId":396367,"journal":{"name":"Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan","volume":"4 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2022-03-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115584286","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}