{"title":"Analysis and design of subnetting methods: Hybrid fixed length subnet masking (HFLSM)","authors":"Afwarman Manaf, D. S. Bataona","doi":"10.1109/ICEECS.2014.7045228","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045228","url":null,"abstract":"By doing subnetting, network address can be broken down into several smaller subnets blocks to match the needs of the host address or subnet block. There are several known methods of subnetting ie VLSM and FLSM. In the application example in the case of this research, the results of the analysis indicate that the use of VLSM with a presentation method in terms of effective and efficient by 43% compared to the method of subnetting FLSM. With the same case will try to apply a new technique that is AFLSM. This technique is able to reduce the amount of wasted host better than VLSM, but this technique is not generic and can only be applied in certain cases. This technique also uses a subnet mask pattern is confusing and not in accordance with the standard value of CIDR. To overcome the shortcomings experienced by AFLSM, in this paper proposed a new technique that is HFLSM. HFLSM technique is a technique or a combination of the combined results VLSM and AFLSM. HFLSM techniques using pattern management IP addressing calculation as AFLSM but with a little addition of some rule. While the use of the subnet mask, this technique uses the pattern of use of VLSM subnet mask held that the use of subnet mask IP address will not overlap between the one with the other and the corresponding standard CIDR value. HFLSM more generic when compared with AFLSM, because the application of HFLSM can be done in several different instances. HFLSM also have reduced the ability of IP addresses are wasted or not used better than VLSM in a particular case.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"13 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115636264","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Andri Setiyoso, H. Hindersyah, A. Purwadi, A. Rizqiawan
{"title":"Design of traction motor 180kW type SCIM for KRL (EMU) Jabodetabek re-powering project","authors":"Andri Setiyoso, H. Hindersyah, A. Purwadi, A. Rizqiawan","doi":"10.1109/ICEECS.2014.7045274","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045274","url":null,"abstract":"In 1995, Indonesia began operating the first electric train manufactured by local companies. This EMU was created by a consortium of state-owned enterprises in Indonesia (PT. INKA (Persero), PT. LEN (Persero) and PT. PINDAD (Persero)) with a consortium Belgien - Nederlandsch - Holland Electric (BN - Holec). PT. PINDAD (Persero) in charge of transferring technology in traction motor design. KRL Jabodetabek (Jabodetabek EMU (Electric Motor Car Unit)) is a rail-based transportation that serves the area with operation region covering the Capital State and several surrounding cities (DKI Jakarta, Bogor City, Depok City, Tangerang City, and Bekasi City). KRL BN-Holec is the first electric trains manufactured in Indonesia. This KRL BN-Holec was designed to meet the passenger demand back at 1995, however in the early year 2000 the passenger demand has already increased significantly. Therefore, a new design of motor traction suitable for KRL BN-Holec which meet the new passenger demand is needed. In this paper, a new design of traction motor 180 kW for KRL BN-Holec application is proposed. By using the proposed design, the power density can be increased without sacrificing the performance. It can be shown that the experimental result proves that the proposed design meet the performance required.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123092086","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
K. Diharjo, Sutrisno, Triyono, R. Afandi, D. A. Himawanto
{"title":"Enhancing of fire resistance on CFRP using Sokka-clay particle for lightweight car body panel","authors":"K. Diharjo, Sutrisno, Triyono, R. Afandi, D. A. Himawanto","doi":"10.1109/ICEECS.2014.7045243","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045243","url":null,"abstract":"The silent transportation with zero emission, especially electrical vehicle, becomes an alternative vehicle for supporting the environmentally friendly cities. The use of lightweight materials with high fire resistant are needed to be applied on the vehicle, like composites. The enhancing of fire resistant on carbon fiber reinforced composite (CFRP) may be performed using local Sokka-clay to replace the volume of fiber partially. The specimens of CFRP can be produced by using a press moulding method. For the same filler/fiber content, the the increasing of CF laminates content enhances the burning properties of CFRP. According to UL 94 standar, all these CFRP composites can be classified as Horizontal-Burning A (HB-A), and that containing 40%CF is self-extinguishing (HB-C). The percentage of remaining mass is higher for the more particles content, because of the more remains of ferro oxide and calcium oxide particles after the heating process. The more CF content increases the material cost of CFRP due to the price of CF. But, the addition of clay particle gives many advantages on CFRP, such as burning properties, thermal properties, and more economical product. This CFRP has also good prospect to be applied in EV to reduce its weight.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"78 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"117144288","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Academic ranks promotion in higher education in Indonesia during 1987–2014","authors":"Y. Haroen, Supriadi Rustad","doi":"10.1109/ICEECS.2014.7045262","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045262","url":null,"abstract":"The system of academic rank structure and first appointment regulation for academic staff has been established since 1987, this applied for either state and private-owned universities. The academic rank structure was divided into 9 level, starting from Associate Lecturer rate 100 credit points up to Full Professor rate 1000 credit points. Two years of staying in the previous position was mandatory before promotion to the higher rank, and accelerating or office caper was not possible. New regulation introduced in 1999 transformed the academic rank structure became simpler. By this new regulation Head Lecturer has been considered as associate professor level with rate 400, 550, and 700 credit points, while Professor rank rates 850 and 1050 credit points. It is eligible to get a rate promotion in the same academic ranks after 2 years in the current rate. However, The rate promotion is not possible if the adjacent rate belong to higher academic rank. A new statute passed by the parliament in 2006 stated that part time lecturer is no longer have academic ranks and also abolished Associate Lecturer rank rate 100 credit points. To have a promotion to be Professor from Head Lecturer rank, the candidate should publishes at least 1 article in accredited journal by Directorate General of Higher Education (DGHE) of Ministry of Education and Culture and fulfill the credit points needed. Special circumstances apply for office caper who jump directly from Associate Lecturer to Head Lecturer or from Lecturer to Professor, the candidate should has published at least 4 articles in acredited national journal, or equivalently 2 articles in international reputable journal. Since 2011 the DGHE has already implemented a new tighter assesment for academic rank promotion although still under the same regulation.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126024198","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Synthesis and analysis of chitosan-lithium battery cell in various charge/discharge currents","authors":"A. Rochliadi, Multazam, I. Arcana, B. Bundjali","doi":"10.1109/ICEECS.2014.7045259","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045259","url":null,"abstract":"Electricity is a form of energy that can be easily transformed into other energy forms. The purpose of this study is to analyze the chitosan-lithium battery cells. It is found that the energy of chitosan-lithium battery cells will give decreases with the decreasing of given discharge current at a very small percentage value. The greatest energy efficiency given by battery cell with charge current at 1C and discharge current at 0.2C is 12.55%. The conductivity of chitosan-lithium membrane found to be 1.25 × 10-4 S.cm-1 after charge/discharge test. At charge currents 1C, high discharge (2C and 1C) current gave higher resistances compared to lower currents (0.5C and 0.3C). ReSr value tends to decrease with decreasing discharge currents is given. However, charge current 0.7C and discharge current 0.2C did not show any significant difference between the low discharge currents and the high discharge currents.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"62 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122122993","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
A. Jamaluddin, F. Perdana, A. Supriyanto, A. Purwanto, Inayati, M. Nizam
{"title":"Development of Wireless Battery Monitoring for electric vehicle","authors":"A. Jamaluddin, F. Perdana, A. Supriyanto, A. Purwanto, Inayati, M. Nizam","doi":"10.1109/ICEECS.2014.7045235","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045235","url":null,"abstract":"A Wireless Battery Monitoring System (WBMS) for electric vehicle has been developed for monitoring voltage, current and temperature of battery. This system consists of hardwares (sensors, a microcontroller, a bluetooth module, an Android smartphone) and software. It was designed on a low cost microcontroller ATMEGA 328 (Arduino UNO). Voltage, current and temperature data are transfered to microcontroller, then data of battery is transfered using bluetooth communication to display. In this research, data of battery monitoring are displayed on Personal Computer (PC) with LabVIEW programme and android smartphone. The monitoring system was able to show real-time data of voltage, current and temperature and display data on android smartphone and PC simultaneously.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130588908","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Dispersion relation of 1-D photonic crystal","authors":"F. Akbar, A. Syahriar, A. Lubis","doi":"10.1109/ICEECS.2014.7045222","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045222","url":null,"abstract":"Photonic crystal is a periodic dielectric material that affect the propagation of light. That produces a photonic bandgap. Photonic bandgap is a structure where a range of frequency cannot propagate through the structure. The characteristics can bee seen from the dispersion relation of the light propagate in the structure. In this paper, we use two different methods to simulate the dispersion relation; firstly we use a Plane wave method and secondly we use a transfer matrix method. Both methods use a different approach to describe the periodic dielectric structures. In the simulation we try to compare both results and show them in graph of wavevector k vs frequency, with unit cell consisting GaAS as material of the dielectric and air as the gap. The width of GaAS is 0.8 micron and width of the air gap is 0.2 micron. We also rescaling both normalized frequency to be the similar. In the process we examine the normalised frequency values using both methods as well as the difference results appears on the calculations.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"66 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130593405","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
M. Nizam, Hery Tri Waloyo, Agus Mujianto, Inayati, A. Purwanto
{"title":"Brushless DC motor torque improvement with mgnetic material stator core","authors":"M. Nizam, Hery Tri Waloyo, Agus Mujianto, Inayati, A. Purwanto","doi":"10.1109/ICEECS.2014.7045237","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045237","url":null,"abstract":"In transportation, BLDC motors are required to have high torque. This BLDC electric motor is designed to drive an electric car. Increased torque can be done in many ways one of which is the selection of the stator material. Effect on the generated torque can be studied by replacing its stator materials. Design was begun with determining the electrical circuit and the coil for the excitation power. Electric motors which was simulated in this paper was a 3-phase BLDC motor. Voltage and current data were analyzed to study the motor performance when different core materials used. It can be concluded that applying ferrite materials stator core reduced core loss, while using ferrite core on the stator slots produces higher voltages and lower currents. Based on the magnitude of the torque produced by the electric motors, ferrite materials was more suitable to be used as slots of the stator core for better motor.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"7 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121769348","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Video-based system development for automatic traffic monitoring","authors":"Okaswara Perkasa, D. H. Widyantoro","doi":"10.1109/ICEECS.2014.7045254","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045254","url":null,"abstract":"Traffic jam poses a serious problem because it creates distress and causes inefficiency of fuel consumption. Part of the solution to this problem is a system that can automatically detect the traffic congestion level in a road segment. This paper reports our work on developing such a system. It assumes a fixed camera is attached on high location, enabling it to monitor traffic flow in a specified road segment. The frame of video stream is analyzed by estimating the traffic density and traffic speed from the moving vehicles. The combination of traffic density and traffic speed is used for classifying the traffic congestion level, either belonging to free flow, slow moving or congestion category. Our evaluation using two traffic videos reveal a high accuracy of traffic congestion level prediction.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"4 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115799399","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Evaluating Indonesian C2C and B2C quality using eQual: A preliminary research","authors":"N. Rahayu, F. Anggriawan","doi":"10.1109/ICEECS.2014.7045238","DOIUrl":"https://doi.org/10.1109/ICEECS.2014.7045238","url":null,"abstract":"E-commerce is increasingly popular, both in terms of functionality and coverage. Depending on the parties involved, e-commerce comes in many forms, such as C2C, B2C, B2B, and C2B. In Indonesia context, recent survey shows a growing number of Indonesian internet users and also online shoppers. To capture Indonesia e-commerce quality, we develop a preliminary study focusing on C2C and B2C. As sample, we choose the two best providers for each category and use eQual Index (EQI) to assess them. We asked 89 respondents from January to February 2014 using eQual questionnaire. The validity and reliability test shows all of the questions to be valid. The survey has been delivered online, and overall, the result showed that both EQIs are almost equivalent. It means all B2C and C2C qualities are equal. We also found online users perceived trust as the critical factor for e-commerce, and the C2C best player has outstanding value on empathy component. This study delivers each e-commerce strength and weakness and gives implicit recommendation to fulfil the gap to attract more customers in the future.","PeriodicalId":368243,"journal":{"name":"2014 International Conference on Electrical Engineering and Computer Science (ICEECS)","volume":"5 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2014-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132264466","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}