{"title":"Assessing the Influence of Asymmetric Modes on the Reliability Indicators of Distribution Systems","authors":"Fiodor Erhan, Dinu Voinesco","doi":"10.32515/2414-3820.2021.51.88-94","DOIUrl":"https://doi.org/10.32515/2414-3820.2021.51.88-94","url":null,"abstract":"The power electric distribution systems (PEDS) possess a great dynamics of development. Thanks to this phenomenon in the power electric distribution systems (PEDS) the probability of apparatus of asymmetrical regimes increase monotonously. As a result of this reliability of the functioning of the power electric equipment installed in the electric knots changes. The asymmetrical regimes in the power electric distribution systems (PEDS) accompanied by the short circuit current are a function of a row determinate is a vague factor of probabilistic nature. Coming from it follows that the investigation of the influence of the asymmetrical regimes accompanied by the current of the short circuit on the reliability of the Power Electric Distribution Systems (PEDS) is one of the most important problems of the development the Power Electric Distribution Systems. The short circuit currents influence the structural and functional reliability of distribution networks and at the reliability of electrical equipment installation. The dynamics of changes in the levels of short circuit currents in electrical networks depends on the rate of change of the re-recovering voltage at the short circuit point on the power supply side and on the load side, as well as on the magnitude and rate of power change at the short circuit point on the power source side and on the load side.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"44 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132149204","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Mathematical Simulation of Energetics and Economics Parameters of the 4DC-125/110 Engine Based on Thermodynamical Calculation Supplying by Various Types of Fuel","authors":"A. Dichii, P. Voleac, Eduard Banari","doi":"10.32515/2414-3820.2019.49.75-82","DOIUrl":"https://doi.org/10.32515/2414-3820.2019.49.75-82","url":null,"abstract":"","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"68 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131351472","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Experimental Research of the Working Process of the Pneumatic Conveyor of the Combed Heap","authors":"V. Holovlov, Oleksandr Lezenkin","doi":"10.32515/2414-3820.2021.51.46-53","DOIUrl":"https://doi.org/10.32515/2414-3820.2021.51.46-53","url":null,"abstract":"The article presents the advantages of harvesting grain ears by the method of combing at the root use stripper harvesting module technology with subsequent processing in comparison with combining. Harvesting with this technology is performed by a trailed harvesting machine with stripper working bodies. The implementation of this technology is constrained by namely the lack of scientific substantiation of the operating modes of the pneumatic conveyor of the combed heap. In this regard, there is a problem of researching the pneumatic conveyor, for its solution a method of experimental research was developed, which will determine the optimal parameters and performance of the pneumatic conveyor combed heap.The results of experimental researches of technological process of the pneumotransporter for transportation of the combed heap of grain in the trailer - the cart, namely range of flight of the combed heap depending on frequency of rotation dampers. The parameters of the factors and the geometric dimensions of the experimental setup were determined by computer simulation in SolidWorks. During the simulation, a full-fledged computer model was developed in real size, where the parameters were obtained by changing the speed of the impeller and changing the geometry of the loading window and the pneumatic line. Using the results of theoretical research, modeling and analysis of literature sources, the limits of the values of the factors were determined, which are given in the table. To conduct experimental research, an experimental setup was made, which allowed to vary the values of variable factors, and thus obtain a variety of data on the range of the combed pile of wheat depending on the values of variable factors. It is established that it is most expedient to use a noncomposite three - level Box - Benkin plan for three factors, which makes it possible to obtain a mathematical model according to the conducted experiments. The mathematical model is obtained, which in the future will make it possible to establish rational parameters and modes of operation of the compressed heap pneumatic conveyor. Checking the significance of the coefficients. The significance of the regression coefficients indicated that all the coefficients are significant. Checking the adequacy of the model showed that the model is adequate.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"136 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131704688","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Olexandr Subochev, Y.O. Poloz, V.Y. Malyshchuk, O. Sichko
{"title":"Modeling of Production of Service Companies of Trucks","authors":"Olexandr Subochev, Y.O. Poloz, V.Y. Malyshchuk, O. Sichko","doi":"10.32515/2414-3820.2019.49.221-232","DOIUrl":"https://doi.org/10.32515/2414-3820.2019.49.221-232","url":null,"abstract":"","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"15 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"126024585","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Mathematical Modeling of the Process of Operation of the Drying Chamber of a Tower Grain Dryer With a Suction Air Flow","authors":"V. Shvidia, S. Stepanenko","doi":"10.32515/2414-3820.2020.50.114-121","DOIUrl":"https://doi.org/10.32515/2414-3820.2020.50.114-121","url":null,"abstract":"In the article, a drying scheme in a tower grain dryer has been developed, equations for the conservation of energy and material balance for grain, equations for mass transfer and heat transfer between the drying agent and grain have been drawn up. On their basis, analytical dependences of changes in the temperature and moisture content of grain, moisture content and temperature of the drying agent along and in the width of the drying channel were obtained, depending on the operating parameters (the value of rarefaction in the drying channel, the speed of grain movement along the drying channel, the speed of movement of the drying agent, the initial temperatures of the grain and drying agent, initial moisture content of grain, as well as initial moisture content of drying agent). Their analysis facilitates the work in choosing the optimal mode. The developed analytical dependences of changes in the main drying parameters (moisture and temperature of grain, moisture content and temperature of the drying agent) along the length and width of the drying channel in tower dryers with suction air flow make it possible to link the main operating parameters, which facilitate the choice of rational drying modes.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"274 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116084221","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Theoretical Studies of the Motion of Grain Material Components With Artificially Formed Air Velocity Distribution in the Cross Section of the Channel","authors":"B. Kotov, S. Stepanenko","doi":"10.32515/2414-3820.2021.51.20-35","DOIUrl":"https://doi.org/10.32515/2414-3820.2021.51.20-35","url":null,"abstract":"The purpose of research to formulate a mathematical description of the movement of components of grain material in pneumatic channels with artificially formed distribution of air velocity in the cross section of the channel to improve the quality of separation (trajectory divergence) of grain material components. The article considers studies of grain separation in pneumatic channels with artificially formed air velocity distribution in the cross section of the channel, to determine the rational form and parameters of material supply and options for separation of grain material into fractions. The regularities of grain motion in the form of mathematical models of the dynamics of solid particle motion in air flow are theoretically investigated and established, which differ from those known in that they take into account the action of lateral forces, material concentration, and the application of power law and artificially formed exponential air distribution law) trajectories. The solution of the system of nonlinear differential equations with initial conditions is made in the MathCad software environment in the form of grain motion trajectories in air flow, allows to calculate their motion trajectories that differ in sailing coefficients and determine rational values of pneumogravity and pneumoinertia parameters. Using the obtained dependences for the development of air separators, it is possible to determine the initial velocity of entry and direction of entry of grains into the air stream, as well as to determine the trajectories of the material in the air ducts with lower material unloading. Conclusions: 1. Theories of grain motion are theoretically investigated and established in the form of mathematical models of solid grain motion dynamics in air flow, which differ from those known in that they take into account the action of lateral forces, material concentration, and the application of power and artificial exponential law (splitting) of grain movement trajectories by 20%. 2. The solution of the system of nonlinear differential equations with initial conditions is made in the MathCad software environment in the form of grain motion trajectories in the air stream, which allows to calculate their motion trajectories differing in sailing coefficients and determine rational values of pneumogravity and pneumoinertial separators.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"26 1-2 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116555566","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Determination of Rational Parameters Pneumomechanical Seeding Machine with Peripheral Arrangement of the Cell and Inertial Edition of Extra Seeds`","authors":"K. Vasylkovska","doi":"10.32515/2414-3820.2019.49.59-66","DOIUrl":"https://doi.org/10.32515/2414-3820.2019.49.59-66","url":null,"abstract":"","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"76 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132718091","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A methodical Approach to Substantiating the Performance Indicators of the Machine-Tractor Unit Using Energy-saving Technologies","authors":"R. Kudrynetskyi, V. Dnes, S. Krupych","doi":"10.32515/2414-3820.2022.52.48-55","DOIUrl":"https://doi.org/10.32515/2414-3820.2022.52.48-55","url":null,"abstract":"The article considers a mathematical model for determining the operational indicators of a machine-tractor unit, for determining a rational fleet of farm machines that ensures the performance of work with minimal operating costs and in optimal agrotechnical terms. The structure of operating costs during the cultivation of agricultural crops using different technologies was obtained. Patterns of changes in operational costs for growing crops using No-till and Strip-till technologies. The application of these regularities makes it possible to obtain predictive values of the efficiency of the use of the farm's machine-tractor park even at the planning stage. The choice of technical means must be carried out taking into account the requirements of agricultural techniques for growing agricultural crops, zonal soil and climatic conditions and the condition of the fields. To ensure the performance of works with minimal operating costs, it is necessary to equip the machine and tractor park with technical means that ensure high-quality performance of works in optimal agrotechnical terms. It was established that in the structure of the total operational costs for growing agricultural crops using intensive technology, about 55...66% are the costs of technological materials used during the cultivation of agricultural crops.The developed mathematical model for determining the performance indicators of the MTA makes it possible to obtain predictive values of the efficiency of the use of the farm's machine-tractor fleet even at the planning stage.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"23 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133751529","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
V. Bokov, O. Sisa, V. Mirzak, Volodymyr Sviatskyi, V. Shmelyov
{"title":"Physical Features of The Process of Multi-operation Extraction of Cylindrical Parts From a Metal Mesh","authors":"V. Bokov, O. Sisa, V. Mirzak, Volodymyr Sviatskyi, V. Shmelyov","doi":"10.32515/2414-3820.2022.52.135-155","DOIUrl":"https://doi.org/10.32515/2414-3820.2022.52.135-155","url":null,"abstract":"In modern mechanical engineering, a method of single-operation extraction of cylindrical parts from a metal grid with a square mesh is known, which, in particular, has found application for the manufacture of microphone casings. Further improvement of the technology of extracting parts from a metal mesh in the direction of increasing the relative height of the stamped part is associated with the use of a multi-operation method of extraction. The study of this process will allow to significantly reduce the limit coefficient of extraction and thereby significantly increase the relative height of the part. Therefore, the work aimed at improving the technology of manufacturing parts from a metal mesh due to the use of a multi-operation method of extraction is an urgent scientific and practical task. The purpose of the study is to improve the technology of manufacturing cylindrical parts from a metal mesh by using a multi-operation method of drawing. The result of the work is the study of physical limitations that determine the limiting coefficient of multi-operational extraction of cylindrical parts from a metal mesh. The phenomenon of elasticity of the mesh wires was revealed, as a result of which the side wall of the part acquires a curved, close to conical shape. The physical similarity between the process of deformation of a single wire of a metal mesh during multi-operation drawing and the process of bending a flat workpiece is shown, which allows determining the technological effort of each drawing operation using formulas for calculating the bending force. In addition, two forms of instability of the process of multi-operational drawing of cylindrical parts from a metal grid with a square mesh were revealed, and a new method of drawing was proposed, which creates such stamping conditions, in which asymmetric deformation of the part (irreparable defect) is not observed, and separate additional means for cutting the edge of the stamped parts are not used.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"24 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133927675","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Improve the Durability of a Turbocharger as a Result of Repair Work","authors":"Yuriy Kuleshkov, M. Chernovol, Timofey Rudenko","doi":"10.32515/2414-3820.2021.51.169-174","DOIUrl":"https://doi.org/10.32515/2414-3820.2021.51.169-174","url":null,"abstract":"A turbocharger is a unit of modern internal combustion engines designed to boost it. Since a drive of the turbocharger is most often carried out from the energy of the exhaust gases, the conditions of its operation can not be called favorable: the temperature of the exhaust gases sometimes reaches 7000C, high chemical activity of the exhaust gases, high speed of rotation of the turbine. The consequence of difficult operating conditions is the wear of its elements. One of the main causes of wear of the active elements of the turbocharger is abrasive wear. Various methods of restoration and strengthening can be used to restore machine parts. However, not all methods can provide the necessary resource for the restoration and strengthening of parts working in abrasive and corrosive environments. One of the modern directions of increasing the wear resistance and other properties of reducing coatings is the use of composite materials. This article presents the results of research on the development of a new method for restoring and strengthening parts with composite materials based on the use of chemical vapor deposition of metals CVD - method (Chemicikal Vapor Deposition) by decomposition of organometallic compounds. It is shown that the developed composite material obtained by the CVD-method of decomposition of organometallic compounds provides an increase in wear resistance of at least 2.0...2.2 times in comparison with new parts composite material. Vapor-phase deposition of metals, Chemicikal Vapor Deposition-method, decomposition of organometallic compounds.","PeriodicalId":302253,"journal":{"name":"National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines","volume":"291 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"1900-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"134555874","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}