C. Seuring, A. Huber, F. Passek, W. Ammon, T. Muller
{"title":"Impact of nitrogen doping on gate oxide integrity on 300 mm silicon wafers after RTP in hydrogen ambient","authors":"C. Seuring, A. Huber, F. Passek, W. Ammon, T. Muller","doi":"10.1109/RTP.2002.1039455","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039455","url":null,"abstract":"300 mm silicon wafers with nitrogen content >1.0/spl times/10/sup 15/ at/cm/sup 3/ and without nitrogen doping (reference group) were subjected to a rapid thermal annealing process in an atmosphere of 60% hydrogen in argon. The gate oxide integrity (GOI) improvement of the annealed nitrogen-doped wafers was investigated and compared to the reference group. Additionally, the depth dependence of the GOI-improvement by annealing was evaluated. At 200 nm depth the defect density of the RTP-treated wafer was again comparable to the respective reference wafer defect density. The defect morphology change induced by hydrogen RTP was investigated via AFM measurements.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"74 3 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"121037305","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
G. Stuart, D.M. Camm, J. Cibere, L. Kaludjercic, S.L. Kervin, B. Lu, K.J. McDonnell, N. Tam
{"title":"Temperature diagnostics for a dual-arc FRTP tool","authors":"G. Stuart, D.M. Camm, J. Cibere, L. Kaludjercic, S.L. Kervin, B. Lu, K.J. McDonnell, N. Tam","doi":"10.1109/RTP.2002.1039443","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039443","url":null,"abstract":"Vortek's new 300 mm flash-assist RTP/spl trade/ tool uses a pair of arc lamps to heat wafers at >200/spl deg/C/s to an intermediate temperature of between 700/spl deg/C and 1200/spl deg/C. A high power, millisecond duration flash is then applied to the device side of the wafer, raising it to a higher peak temperature. Water-cooled windows and the cooling walls of the arcs attenuate incident radiation at the diagnostic wavelength of 1450 nm. This facilitates measuring the temperature of both wafer surfaces during the entire thermal process. A fast radiometer, which samples the back surface of the wafer at 25 kHz, provides feedback to a 1 kHz arc control system. An emissometer measures the back-surface emissivity, while one of its components, a near-infrared camera, provides a two-dimensional map of wafer temperature. An ultra-fast radiometer, which samples at up to 1 MHz, measures the device side of the wafer and estimates the peak temperature of the wafer during the flash. This radiometer has dynamic re-calibration and temperature-compensated electronics. All detectors are InGaAs. The fast radiometer, the ultra-fast radiometer, and the camera have effective resolutions of 16, 14, and 11 bits respectively. The individual components of the temperature measurement system are described. The methodologies used to achieve intermediate temperature control of better than /spl plusmn/2/spl deg/C and emissometer stability of /spl plusmn/0.2% are discussed.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"152 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123268825","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Measurement of nonthermal illumination-enhanced diffusion in silicon","authors":"M. Jung, E. Seebauer","doi":"10.1109/RTP.2002.1039451","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039451","url":null,"abstract":"Continued scaling of ultrashallow junctions in transistor devices raises the possibility that new physical effects connected with intense lamp illumination during rapid thermal annealing (RTA) need to be incorporated into models for transient enhanced diffusion (TED). Identification of such effects is difficult in conventional RTA geometries because lamps provide both heating and photostimulation, and because the interpretation of conventional dopant diffusion experiments is impeded by complex dopant-defect interactions and the presence of built-in electric fields in typical test structures. In this paper we present strong experimental evidence of nonthermal illumination-enhanced diffusion in unimplanted silicon.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"14 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130397745","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Systems analysis applied to modeling dopant activation and TED in rapid thermal annealing","authors":"R. Gunawan, M. Jung, R. D. Braatz, E. Seebauer","doi":"10.1109/RTP.2002.1039447","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039447","url":null,"abstract":"Insufficient dopant activation and excessive transient enhanced diffusion (TED) of boron in silicon has been major inhibitors to forming low-resistivity ultrashallow junctions for CMOS device applications. However, the predictive capability of most simulation-based models is subject to serious doubt. Here we apply several mathematical methods drawn from systems analysis to greatly reduce the magnitudes of these uncertainties and to determine optimal temperature trajectories. We begin by outlining firmly grounded procedures for estimating simulation rate parameters using maximum likelihood estimation together with multivariate statistics to quantify accuracy. We also describe a rigorous parameter sensitivity analysis by the finite difference method to investigate model behavior. These combined approaches not only lead to vast improvements in the ability of simulations to match experiment, but also show that, out of roughly 30 total parameters in the model, only 4 need further serious attention as targets for determination by independent experiments or quantum calculations.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"64 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124135217","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Rapid thermal curing of low-k spin-on films","authors":"R. Sharangpani, S. Tay","doi":"10.1109/RTP.2002.1039453","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039453","url":null,"abstract":"We have used short time, high temperature, and high ramp-rate thermal cycles for curing organic low-k spin-on films in a rapid thermal processing (RTP) system. We show that such cycles can give lower copper diffusion through barrier layers than the conventional low temperature, long duration cycles carried out in furnaces. In addition, a highly controlled ambient is needed to prevent film oxidation. All of these requirements make RTP ideally suited for low-k film curing. Therefore, RTP can enable integration of low-k films in advanced interconnect schemes.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"11 3 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123683765","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
W. Zagozdzon-wosik, M. Ranjit, D. Ravindranath, Z. Zhang, J. Charlson, I. Rusakova, P. van der Heide, L. Larson, J. Bennett, R. Tichy, M. Beebe
{"title":"Conductive borides used for junction formation and integration with contacts in deep 0.1 /spl mu/m MOSFETs","authors":"W. Zagozdzon-wosik, M. Ranjit, D. Ravindranath, Z. Zhang, J. Charlson, I. Rusakova, P. van der Heide, L. Larson, J. Bennett, R. Tichy, M. Beebe","doi":"10.1109/RTP.2002.1039452","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039452","url":null,"abstract":"Future generations of CMOS integrated circuits (IC) face challenging requirements to lower parasitic resistances associated with the source and drain (SID) regions. New solutions are necessary as the current technology cannot provide parameters of ultra shallow junctions and their contacts to would allow avoiding device degradation. We studied properties of titanium boride layers and process integration issues for potential application of such films in the SID engineering focused on both junction and contact formation. Controlled dopant outdiffusion, obtained by RTP conditions, resulted in either diode fabrication on n-type silicon or ohmic contacts on p-type substrates. Complementary analytical techniques including RBS, XPS, SIMS, and TEM as well as various electrical measurements on test structnres allowed for identification of the most difficult process constrains.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"18 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"131642690","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Rapid thermal processing of high dielectric constant gate dielectrics for sub 70 nm silicon CMOS technology","authors":"M. Fakhruddin, R. Singh, K. F. Poole, S. Kar","doi":"10.1109/RTP.2002.1039444","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039444","url":null,"abstract":"The use of high-/spl kappa/ gate dielectrics in place of the currently used Si-based gate dielectrics has the potential to push Si complementary metal-oxide-silicon (CMOS) technology to the fundamental limit of about 10 nm feature size circuits. Rapid thermal atomic layer chemical vapor deposition (RTALCVD) is used to deposit ZrO/sub 2/ on Si substrates to fabricate MIS structures. The leakage current and capacitance measurements were done to analyze their electrical properties. Achieving low leakage current density along with high capacitance per unit area demonstrates the superior performance of our process.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"19 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"133121575","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Establishing advanced implant annealing for the 65 nm technology node","authors":"A. Jain, L. Robertson","doi":"10.1109/RTP.2002.1039436","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039436","url":null,"abstract":"An essential requirement for the continued scaling of CMOS technology is the ability to fabricate junctions with decreased depth and increased abruptness without compromising the maximum activation level of dopants. Reduction of ion implantation energy has been instrumental in meeting this requirement and will play an important role in the future. However, advances in annealing technology continue to be critical in order to realize the potential benefits of lower energy implants. Spike anneals, in which the wafer only spends 1 to 2 s within 50/spl deg/C of the peak temperature, are playing a key role in 130 nm and 90 nm node technologies. These anneals have proved successful in mitigating enhanced diffusion effects. They have enabled superior junctions by allowing annealing at higher temperatures to increase electrical activation while limiting diffusion by virtue of sharper temperature-time profiles. Employing temperature-time profiles of greatly increased sharpness can extend this principle further. We have used a flash-lamp based system to investigate the evolution of dopant profiles and the associated damage structure following low-energy ion implantation. Peak temperatures of values up to 1300/spl deg/C were used while the sharpness of the temperature-time profile was sharpened in to the sub-millisecond range. Profiles with significantly reduced junction depths have been obtained without compromising high active concentration. This method has the potential to produce profiles with improved abruptness but we show that this is sensitive to the choice of implantation conditions. Under optimized conditions it is now possible to take full advantage of reducing implantation energy and produce profiles that can be expected to enable device technology at the 65 nm node and beyond.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"14 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"134055520","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Comparison of silicon wafer temperature measurements using thin film thermocouples and lightpipe radiation thermometers in a thermometry test bed","authors":"K. Ball, G.Y. Tan","doi":"10.1109/RTP.2002.1039442","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039442","url":null,"abstract":"This paper reports on the results of a research study to compare the temperature measurements obtained using NIST (National Institute of Standards and Technology) thin-film. thermocouple calibration wafers and other commercial calibration wafers to those of lightpipe radiation thermometers (LPRTs) from at least two commercial manufacturers. These comparisons have been performed in the UT (The University of Texas at Austin) RTP Thermometry Test Bed, which has been previously described. The LPRT-to-thermocouple comparison measurements have been made at temperatures ranging from 700/spl deg/C to 900/spl deg/C in the UT Test Bed. The Thermometry Test Bed is a joint project by UT, NIST, SA (SensArray Corporation) and ISMT (International SEMATECH) under Sponsored Research Agreement No. 38060302. The Test Bed facility is evolving into a temperature standard, traceable to ITS-90, for commercial sensors (OEM pyrometers) targeting applications in RTP and (MO)CVD. The Test Bed facility can accommodate a wide variety of commercial sensors. The performance of the Test Bed is indicated by the following wafer temperature characteristics: run-to-run repeatability better than /spl plusmn/1.0/spl deg/C at 1000/spl deg/C, and overall temperature uniformity better than /spl plusmn/1.5/spl deg/C across the wafer (better than /spl plusmn/1.0/spl deg/C at any given radial location). Results using standard TC (thermocouple) instrumented wafers from SA are presented to characterize the performance of the Test Bed, as well as results from the NIST thin-film thermocouple calibration wafers. Several commercial sensor suppliers have initiated tests of their pyrometers. The pyrometers tested in this study are the CI Systems NTM500, and the Mikron Instrument Company's M680S IR Fiberoptic Temperature Measuring System.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"25 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"134521685","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Applications of rapid thermal process to nitridation of tungsten and denudation of WN/sub x/ for poly-Si/Metal gates","authors":"Y. Hu, S. Tay","doi":"10.1109/RTP.2002.1039450","DOIUrl":"https://doi.org/10.1109/RTP.2002.1039450","url":null,"abstract":"To reduce gate RC delay in sub-100 nm CMOS devices, a poly-Si/metal gate electrode stack, consisting of W/barrier/poly-Si layers has become an attractive candidate. Recent studies show that rapid thermal annealing (RTA) of amorphous WN/sub x//poly-Si resulted in denudation of nitrogen atoms with simultaneous in situ formation of low resistivity W and highly reliable barrier layer. This process indicated some advantages, i.e. there is no need for barrier interface, yet device properties superior to those of conventional W/WN/sub x//poly-Si gate has been achieved. The purpose of this paper is to report a study of tungsten nitridation and WN/sub x/ denudation using RTP in various gas ambients, including N/sub 2/, Ar, forming gas (10% H/sub 2/ in Ar), wet H/sub 2/ (16% H/sub 2/O in H/sub 2/) and NH/sub 3/. RTA in a spike fashion in NH/sub 3/ or wet H/sub 2/ for only 2 seconds was used to convert 50 nm WN/sub x/ to pure W. Auger electron spectroscopy (AES) studies indicated that the in situ interface barrier formation with high nitrogen content was completed during the denudation of WN/sub x/.","PeriodicalId":268697,"journal":{"name":"10th IEEE International Conference of Advanced Thermal Processing of Semiconductors","volume":"28 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2002-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"117007229","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}