{"title":"From manufacturing scheduling to supply chain coordination: the control of complexity and uncertainty","authors":"P. Luh, Weidong Feng","doi":"10.1109/ICAL.2007.4338509","DOIUrl":"https://doi.org/10.1109/ICAL.2007.4338509","url":null,"abstract":"With time-based competition and rapid advancements in technology, effective manufacturing scheduling and supply chain coordination are critical to quickly respond to changing market conditions. These problems, however, are difficult in view of inherent complexity and various uncertainties involved. In this paper, decomposition and coordination based on Lagrangian relaxation are identified as an effective way to control complexity and uncertainties. A manufacturing scheduling problem is first formulated within the job shop context with uncertain order arrivals, processing times, due dates, and part priorities. A solution methodology that combines Lagrangian relaxation, stochastic dynamic programming, and heuristics is developed. Method improvements to effectively solve large problems are highlighted. A decentralized supply chain model is then established. By relaxing cross-member constraints, the model is decomposed into member-wise subproblems, and a nested optimization structure is established. Coordination is performed through the iterative updating of cross-member prices without accessing other member's private information or intruding their decision-making authorities, either with or without a coordinator. Two examples are presented to demonstrate the effectiveness of the method. Finally, future prospects are discussed.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2007-10-08","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122379080","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A new intelligent field: metasynthesis engineering","authors":"Xia Cui, Yaodong Li, Ruwei Dai","doi":"10.1109/ICCA.2003.1595111","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595111","url":null,"abstract":"The metasynthesis methodology, i.e. metasynthesis engineering for solving open complex problems was proposed in 1990, which was to combine the human’s mind and the computer’s capability. And a theoretical framework of the implement of metasynthetic engineering, i.e. the hall for workshop of metasynthetic engineering (HWME) was proposed in 1992.The central issue we address within our framework is to explore the metasynthetic engineering as a new intelligent field by means of artificial intelligence, knowledge engineering, system science, system thinking, Dialogue, knowledge management and www technology, which involves experts, computer, intranet and internet, which meta-synthesize the human intelligence, the high capability of computer, the intercourse platform–intranet-of knowledge creativity and organizational creativity, the collective intelligence on some certain topic of millions of web users from the internet, which emerges the collective intelligence from the network of HWME established by the inter-response embodied in the contents of interactions among components. And we have developed the algorithm tools, i.e. analysis of the link structure of HWME to distill the emergent collective wisdom on some topic.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"97 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115228312","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Fault diagnosis techniques: Application to the thermoforming process","authors":"N. Aouf, B. Boulet","doi":"10.1109/ICCA.2003.1595089","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595089","url":null,"abstract":"This study presents two fault detection and isolation techniques for thermoforming reheat process actuators. The actuators are the top and bottom oven heating bands. The second technique presented, called generalized Kalman filter scheme, is more innovative and showed better fault isolation compared to the first technique of this study called the direct Kalman filter scheme (DKFS).","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"9 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"115639638","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Modeling and Simulation of A Commercial Medium Sun Sensor","authors":"J. Lee, K. Di Filippo, A. Ng, C. Ribe","doi":"10.1109/ICCA.2003.1595118","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595118","url":null,"abstract":"Sun sensors are widely used in spacecraft attitude determination and control systems (ADCS), while an analytical model of a sun sensor would help in spacecraft ADCS design, analysis, and simulation. This paper derives an analytical model of a commercial medium sun sensor, which, to the knowledge of the authors, has not been seen in literature. In addition, the model is validated with experiments by comparing model outputs with experimentally measured outputs of the sensor. Both sets of results coincide quite well. Furthermore, the possible sources of modeling errors and the measures to eliminate them are discussed.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"68 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"123103197","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A Software Environment for Aircraft Modern Control Design and Simulation","authors":"Madjid Haouani, O. Akhrif, Maarouf Saad","doi":"10.1109/ICCA.2003.1595042","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595042","url":null,"abstract":"Improving the efficiency of the control laws design process represents a great challenge for the coming years in the field of flight control. This is due to the increasing requirements from industry in terms of robustness to uncertainties. In other words, the flight control laws have to maintain the requested design performance for flight conditions that have not explicitly been used in control design. To meet these objectives, an interactive graphical software environment (ACDA), based upon Matlab/simulink, for the design and analysis of aircraft dynamics and control systems is proposed.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"140 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"125690844","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Two-Degree-Of-Freedom Control with Dual-stage Actuators for Short-Span Seeking in HDD","authors":"Daowei Wu, Youyi Wang, G. Guo","doi":"10.1109/ICCA.2003.1595166","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595166","url":null,"abstract":"In hard disk drive (HDD) servo systems, the short-span track seeking control may be viewed as a reference tracking problem. However, the perfect tracking control (PTC) is difficult to realize, because the voice coil motor (VCM) has a double-integrator behavior with a relative degree of two and it may also have nonminimum-phase (NMP) zero. These characteristics prevent the plant model inversion for the PTC design. A dual-stage HDD servo system uses VCM as the primary actuator and places a secondary micro-actuator piggyback on the VCM. This paper proposes a two-degree-of-freedom (2DOF) control scheme for fast short-span seeking such a system. The control design utilizes the parallel structure of two actuators to relax the restriction of plant order and NMP zero for perfect reference tracking. Experiment results show that the time of short-span seeking can be greatly shortened with the proposed 2DOF control design with dual-stage actuators.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"105 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"116011871","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"On-Line Defect Detection in Web Offset Printing","authors":"N. Shankar, N. Ravi, Zhaowei Zhong","doi":"10.1109/ICCA.2003.1595132","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595132","url":null,"abstract":"This paper presents a detailed description of a vision system developed to detect and locate the non-uniformities that appear on the web offset printing machine. Specifically, the system is capable of monitoring the high-speed web offset printing in a real time environment and alerting the operator of any events (e.g., structural faults, color variations, missing characters, ink splashes, streaks, etc.) that disrupt the uniformities in the web offset printing. Such events are thought to affect crucial printing properties, resulting in non-uniformities in printing and impacting its quality and printability. This paper describes the vision system in terms of its hardware modules, as well as the image processing algorithms that it utilizes to scan the color images and locate areas of defect from the printing web. Basically, the system utilizes high-speed image scanning algorithms to detect edges and boundaries using linear and non-linear filters of dynamic size, threshold and transformation for further analysis. In addition to being tested in a laboratory environment, a prototype of this system was constructed and deployed to a web printing system, where its performance was evaluated under realistic conditions. The system was installed on a Flexo gravure-print-press machine for testing, and it was found that the vision system was able to successfully monitor and detect non-uniformities.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"22 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122853587","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Robust H∞Filtering for Discrete-time Systems with Limited Communication","authors":"Lilei Lu, Lihua Xie","doi":"10.1109/ICCA.2003.1595120","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595120","url":null,"abstract":"This paper jointly considers robust filtering and communication issues. The limited bandwidth in control networks is taken into account when investigating filtering problem under scheduled releasing policy. We adopt the notion of communication sequence. Our objective is to find an optimal sequence and the corresponding filter for a given plant and the communication resource. For a given communication sequence, the problem is formulated into a periodic filtering problem for which a direct LMI design method is developed. Then a heuristic search method is proposed to seek a sub-optimal communication sequence, which greatly reduces the computational cost as compared with the exhaustive search method. An example is given to illustrate the design method.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"4 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122191014","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Forced Singular Perturbations as Theoretical Background to a Split-Coordinate Frame Multirate Strapdown Terrestrial Navigation Algorithm","authors":"J. Waldmann","doi":"10.1109/ICCA.2003.1594978","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1594978","url":null,"abstract":"Forced singular perturbations (FSP) are proposed as a theoretical background to Bar-Itzhack's body−local-level split-coordinate frame multirate scheme intuitively derived for terrestrial strapdown navigation with reduced computations. Forcing the dynamics into distinct time scales caused a degradation of the continuous-time solution, though the loss of accuracy was not significant in comparison with the covered distance. Simulation of ideal sensors undergoing actual operating conditions showed that discretization and use of inertial data in incremental form, however, had a significant impact on navigation acuracy. The interaction between sensor quantization and sensor sampling frequency was investigated. The evaluation of performance in a variety of conditions indicated that the multirate algorithm proposed by Bar-Itzhack, in spite of its elegance and simplicity with reduced computational workload, showed acceptable accuracy in comparison with Savage's more complex multirate correction terms to coning, sculling, and scrolling errors.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128728967","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"On Optimization of Machining Parameters","authors":"Li-Bao An, Ming-Ying Chen","doi":"10.1109/ICCA.2003.1595141","DOIUrl":"https://doi.org/10.1109/ICCA.2003.1595141","url":null,"abstract":"In this paper, an optimization model based on minimum production cost for multi-pass face-milling operations with single-tool applications is presented. Limits on cutting speed, feed rate, depth of cut as well as tool life, surface roughness, cutting force, cutting power are constraints of the model. Optimal values of machining parameters are found by a solution procedure using integer programming. An example is presented to illustrate the optimization model and the solution approach.","PeriodicalId":181531,"journal":{"name":"2003 4th International Conference on Control and Automation Proceedings","volume":"88 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2003-06-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124306384","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}