A.K. Lomunov, A.M. Bragov, M.E. Gonov, T.N. Yuzhina, N.V. Krymov
{"title":"REVIEW OF DYNAMIC PROPERTIES OF WOOD","authors":"A.K. Lomunov, A.M. Bragov, M.E. Gonov, T.N. Yuzhina, N.V. Krymov","doi":"10.32326/1814-9146-2023-85-3-283-311","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-283-311","url":null,"abstract":"This review considers the state of the art in the field of theoretical and experimental studies of dynamic deformation and destruction of wood materials. The orthogonal properties of wood, features of early and late wood are considered, the dynamic properties of wood are analyzed, as well as the influence of the strain rate during dynamic compression. It is noted that wood of different species is mainly used as one of the materials that dampen dynamic loads as a result of impacts or explosions. For example, it can mitigate the effects of high-velocity impacts on the contents of containers during the transport of hazardous materials by air, road and rail. It has been established that the cause of the effects of internal friction in wood are the areas of lignin, in which bundles of cellulose molecules (microfibrils) with a diameter of 25-30 nm are immersed, which are crystalline in their structure, which leads to viscoelastic behavior - internal damping. To improve the damping properties, it is recommended to choose wood with a low microfibril angle. It is noted that the stress-strain curve under dynamic compression of wood consists of three separate parts: the initial elastic region, the yield region and the compaction region. The main characteristics of compression, that is, the components of the stress-strain curve and the destruction of the fibers, do not depend on temperature. Young's modulus is much larger in the longitudinal direction than in the radial and tangential directions. The rate of deformation, temperature and humidity have a great influence on the strength properties of wood. The features of the mechanical behavior of the zones of early and late wood in the massif of a tree trunk are considered. Late wood is more rigid than early wood. As a result, differences in the mechanical properties of the wood fibers during compression may cause the early wood fibers to be destroyed while the late wood fibers remain intact. Due to the complexity of the wood structure, its reliable description by a numerical model requires complex models that take into account not only the influence of temperature, strain rate, and the type of stress-strain state, but also the angle between the direction of loading and the direction of wood fibers. Two main groups of wood material models are considered: micromechanical models simulating the details of the wood structure, and continuum models simulating the behavior of wood as a whole.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"99 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059242","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"TRIAXIAL STRESS STATE OF CONCRETE UNDER LONGITUDINAL DEFORMATION OF TUBE-CONCRETE SAMPLES","authors":"P.A. Khazov","doi":"10.32326/1814-9146-2023-85-2-312-322","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-2-312-322","url":null,"abstract":"The effects that occur during the transition of concrete to a complex stress state, resulting from the limitation of transverse deformations due to the steel shell, are considered using experimental modeling. The studies were carried out on CFST samples of three standard sizes, as well as on differentiated samples of pure concrete and steel tube. Diagrams of work of samples under longitudinal compression and their comparison are given. The use of CFST structures turns out to be very effective not only as a result of saturation of the supporting structure with material, but due to the mutual influence of the components of the structure on each other. A quantitative assessment and a qualitative justification for increasing the efficiency of the concrete core as part of a CFST element are given. It is shown that the increase in the bearing capacity of the sample due to the reinforcement of a simple tube with concrete is several times higher than the differentiated bearing capacity of the concrete core. This fact makes it possible to consider CFST structures as composite ones with a non-linear increase in strength due to the joint work of the system components. The transition of specimens to the plastic state of tube-concrete specimens occurs at the same values of longitudinal deformation as for hollow steel tubes, but at high load values. The effects that occur in concrete under the influence of a steel shell create a triaxial stress state, which makes it possible to multiply the bearing capacity of any brittle material. It is shown that concrete under conditions of such a stressed state behaves rather like an amorphous material, does not collapse at all stages of deformation, and there are practically no processes of crack initiation and its propagation in concrete.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"99 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059262","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"IMPROVING THE MECHANICAL CHARACTERISTICS OF 316L STAINLESS STEEL PRODUCED BY SELECTIVE LASER MELTING AND STUDYING THE EFFECT OF POROSITY ON STRENGTH","authors":"M.Yu. Gryaznov, S.V. Shotin, V.N. Chuvildeev, A.V. Semenycheva, R.K. Musyaev, A.A. Yukhimchuk","doi":"10.32326/1814-9146-2023-85-3-375-389","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-375-389","url":null,"abstract":"The results of experiments on the study of the physical and mechanical properties and microstructure of 316L stainless steel produced by additive technology selective laser melting are obtained. The dependences of the physical and mechanical properties (density, tensile strength, yield strength, elongation to failure, Young's modulus, nano hardness) of 316L steel on the main parameters of the selective laser melting (laser power, scanning speed) are obtained. 316L steel produced by selective laser melting has high mechanical characteristics: tensile strength – 710 MPa; yield strength – 610 MPa; elongation to failure – 48%; relative density – 99.5%, which is comparable to the values obtained for 316L steel produced by traditional methods. These characteristics were obtained using the optimal parameters of selective laser melting: laser power 100 W, scanning speed 200 mm/s, layer thickness 50 ?m, the distance between the scanning tracks is 80 ?m. It is shown that the use of the “volumetric energy density” parameter is usefully for carrying out a primary assessment of technological modes and solving the problem of optimizing the parameters of selective laser melting to obtain a material with high physical and mechanical properties. The nonlinear dependence of the mechanical properties of 316L steel on the main technological parameters can be explained by the influence of porosity arising at non-optimal modes. It is shown that selective laser melting allows controlling the porosity of 316L steel by varying the parameters of the technological mode. Thus selective laser melting makes it possible to produce both a material with a high density close to theoretical values and a material with controlled porosity.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"24 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059064","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"INVESTIGATION OF THE IMPACT OF A POROUS TUNGSTEN IMPACTOR WITH A COMBINED BARRIER","authors":"S.I. Gerasimov, A.P. Kalmykov, A.G. Ioilev, V.A. Kuzmin, S.A. Maskaikin","doi":"10.32326/1814-9146-2023-85-3-414-425","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-414-425","url":null,"abstract":"With high-speed penetration (with velocities more than 2000 m/s), the length of the cavity from a porous striker is greater than from a striker of monolithic (solid) material equal to it in size and density. But at the same time the cavern is narrower, so the volumes of the caverns are almost the same. The process of length reduction and penetration of the strikers (porous and monolithic) for a long time occurs almost identically and only at the last stage of penetration and, especially in the aftereffect phase (after the complete destruction of the striker), there is a difference. This is explained by the fact that during the movement of the porous striker, due to the collapse of the pores, an increase in density occurs, so that the density of the porous striker becomes greater than the density of the solid striker. Then, in the case of a limited thickness of the barrier, the advantage of a porous striker in terms of penetration depth may simply not have time to manifest itself. The results of experiments conducted to confirm this assumption are presented below. The results of experiments on the collision of a porous tungsten impactor with a combined barrier consisting of a steel and polyethylene plate are presented, and the results are analyzed. The problem of numerical simulation of the above experiment by a mesh-free Lagrangian continuous medium modeling method is solved. The calculation model, the results of numerical modeling and a comparative analysis of the results of the experiment and numerical modeling are presented. At the penetration rate V ? 1920 m/s, the porous striker is 2.8% less destroyed when a strong steel barrier is broken through, but in a low-strength polyethylene barrier, the length reduction coefficient of the porous striker is 170% higher relative to the steel one. In addition, a steel striker after breaking through an obstacle (in the air) it does not collapse, unlike porous, which may also be a consequence of the low strength of the latter.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"20 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059068","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"MATHEMATICAL AND MECHANICAL RELATIONSHIP OF CRACKS GRIFFITH AND A NEW TYPE IN SOME NANOTECHNOLOGIY","authors":"V.A. Babeshko, O.V. Evdokimova, O.M. Babeshko","doi":"10.32326/1814-9146-2023-85-3-404-413","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-404-413","url":null,"abstract":"In this paper, for the first time, mathematically strictly, models of Griffiths cracks and cracks of a new type are constructed simultaneously. Accurate models are constructed as a result of the convergence of the ends of two semi-infinite deformable stamps located on a deformable multilayer base. The mechanism of destruction of the medium by cracks of a new type is radically different from the mechanism of destruction of the medium by Griffiths cracks, and has so far been poorly studied. Griffiths formed his cracks with a smooth border as a result of compression from the sides of an elliptical cavity in the plate. Cracks of a new type have a piecewise smooth border, resulting from the replacement of an ellipse with a rectangle compressed from the sides. The construction of models in the work is based precisely on these descriptions of the origin of cracks formed by the ends of approaching deformable stamps. When creating models, the results of previously performed studies on the construction of exact solutions to a number of integral equations of contact problems, published in this journal, are used. The paper found that the destruction of the medium, in the case of cracks of a new type, occurs earlier than in the case of Griffith cracks, which, according to the authors, explains the reason for the destruction of Griffith cracks in the experiment earlier than the theory predicts. Griffiths explained this by the presence of microcracks on the border of the main crack. The authors tend to believe that the cause is the transformation of one type of crack into another, under certain conditions. The results obtained make it possible to compare and quantify the behavior of the medium in the presence of both one and another type of cracks. It is applicable both for the study of mutual transitions of Griffith cracks and cracks of a new type, and for the construction of models of adhesion of wetted nanoparticles.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"39 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059266","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"RECONSTRUCTION OF THE VARIABLE PROPERTIES OF A PIEZOELECTRIC ROD","authors":"A.O. Vatulyan, V.O. Yurov","doi":"10.32326/1814-9146-2023-85-3-340-355","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-340-355","url":null,"abstract":"The problem of reconstruction of variable characteristics (piezoelectric modulus and elastic compliance) of a functionally graded electroelastic rod with steady oscillations is considered when some additional information is given. To formulate the operator relations connecting the desired and measured characteristics, two types of influence are considered: a) by applying a potential difference to the electrodes, b) by applying a force to the end of the rod. Moreover, in the first case, the ends of the rod are free from stress and the current is measured, and in the second case, one of the ends of the rod is rigidly clamped, there are no electrodes, and the oscillation amplitude of the free end is measured. Statements of the corresponding boundary value problems are given in dimensionless form. Asymptotic formulas (quadratic in the frequency parameter) are constructed for the amplitude-frequency characteristics of the current and displacements in the low-frequency range. The inverse problem is solved on the basis of data on the amplitude-frequency characteristics of the current and displacements in a certain frequency range. The solution of the inverse problem is began with the procedure for choosing the initial approximation, and then it is constructed in an iterative manner. At each iteration, the direct problem with known characteristics is solved and corrections are found based on the solution of the system of Fredholm integral equations of the first kind with smooth kernels using the regularization method of A.N. Tikhonov. To find the initial approximation, the constructed asymptotic formulas are used, as well as the method of minimizing the residual functional. The conditions are described under which the non-uniqueness of the solution of the inverse problem is possible. The results of computational experiments on the simultaneous restoration of two functions are presented. The choice of the most informative frequency ranges is discussed. The various methods for choosing the initial approximation are considered. To control the iterative process, the plots of the residual in the frequency response and plots of the reconstruction error depending on the iteration number are given.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"51 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059251","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
D.V. Tarlakovskii, G.V. Fedotenkov, None Mai Quoc Chien
{"title":"LONGITUDINAL TRANSIENT VIBRATIONS OF A FINITE MOMENT ELASTIC ROD","authors":"D.V. Tarlakovskii, G.V. Fedotenkov, None Mai Quoc Chien","doi":"10.32326/1814-9146-2023-85-3-390-403","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-390-403","url":null,"abstract":"Non-stationary longitudinal vibrations of a moment elastic rod of finite length are investigated. To describe the motion of the rod, the system of equations of the general model of moment elastic thin bodies is used without additional hypotheses. The equations of this model take into account longitudinal movements, changes in the angle of independent microrotation, as well as transverse compression of the rod. The rod material is assumed to be homogeneous and isotropic. The system of equations of motion is supplemented by physical relations that describe the relationship of displacements, changes in angles and transverse compression with forces. In contrast to classical models, in addition to normal forces, additional force factors arise in a moment rod. They are: additional moments, moment cutting forces, moments of moment stresses. Accordingly, in addition to the elastic constants of the material, additional physical parameters of the medium are taken into account, which are necessary when taking into account moment effects in the material. The conditions of generalized hinged support are used as boundary conditions at the ends of the rod. The initial conditions are assumed to be zero. To construct the solution, expansions of the desired functions and the external load into trigonometric Fourier series are used. Substituting these expansions into the original relations leads to a system of equations for the coefficients of time-dependent series. To solve it, the integral Laplace transform a in time is used. As a result, expressions for the required coefficients of expansion series in the image space are found. Each of these expressions is the sum of three products. The factors in these products are the Laplace images of the coefficients of the Fourier expansions for the load and for the influence functions. Influence functions are fundamental solutions (Green's functions) of the problem under study. The original coefficients of the series for the influence functions are found analytically using residues. The final expressions for the coefficients of the expansion series of solutions have the form of convolutions in time. The cores of these integral representations are the original coefficients of the series for the influence functions. As an example, the response of a moment elastic rod to the action of a non-stationary axial load is considered. The results obtained are illustrated graphically. The practical convergence of expansion series is estimated.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"25 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059259","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
V.B. Shirokov, B.M. Seredin, P.E. Timoshenko, V.V. Kalinchuk, V.P. Popov
{"title":"THE ROLE OF ELASTIC STRESS DURING THERMOMIGRATION OF LIQUID ZONES BASED ON ALUMINUM IN SILICON","authors":"V.B. Shirokov, B.M. Seredin, P.E. Timoshenko, V.V. Kalinchuk, V.P. Popov","doi":"10.32326/1814-9146-2023-85-3-426-436","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-426-436","url":null,"abstract":"The method of thermomigration of liquid zones based on aluminum makes it possible to create complex structures of closed channels with boundaries formed from p-n junctions in single-crystal silicon wafers. The channels are characterized by the uniformity of their properties, and the pn junctions are characterized by their sharpness. Such structures are used in high-current electronics, photovoltaics, and microelectromechanical converters. Volumetric deformation inside and outside the channel due to alloying of silicon with aluminum leads to the formation of mechanical stresses. The equilibrium shape of the channels formed at high temperatures is determined by the minimum elastic energy and depends on the material parameters and geometry of the structure. Within the framework of the linear theory of elasticity, the behavior of elastic energy during the formation of the structure of thermomigration channels at high temperatures doped with aluminum in a single-crystalline (001) cut disk was studied. The simulation was performed using the finite element method in the COMSOL Multiphysics mathematical package. The study was carried out for practically important structures in which the direction of the edges is oriented along the diagonal of the square. Only such structures do not have breaks during the process of thermomigration. Based on the calculation results, it was revealed that the minimum elastic energy corresponds to structures with different crystalline orientations inside the channel and outside it – in the main silicon matrix. The direction of the crystalline axes inside the channel, corresponding to the minimum elastic energy, is rotated by 45 degrees in the plane of the disk relative to the direction of the axes of the main matrix of the silicon crystal. In addition, calculations showed that with such a turn, the shape of the channels changes. The minimum elastic energy corresponds not to vertical structures, but to inclined ones. The angle of inclination of the pyramids depends on the width of the channels and the distance between them.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"46 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059070","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"INVESTIGATION OF THE PASSAGE OF VIBRATIONS THROUGH A FIXED SECTION OF AN ELONGATED PLATE CAUSED BY THE ACTION OF THE AXIAL FORCE AT THE END","authors":"V.N. Paimushin, V.M. Shishkin, V.A. Gazizullin, A.N. Nuriev","doi":"10.32326/1814-9146-2023-85-3-356-374","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-356-374","url":null,"abstract":"A method has been developed for the experimental study of forced elastic vibrations of a cantilevered thin-walled structural element in the form of a rod-strip, excited due to the passage of vibrations through the section of a finite length fixed along one of the surfaces caused by axial loading by a harmonic force applied to the end of the fixed section. The experimental dependence of the amplitude values of the vibration accelerations of the point at the end of the console on the frequency of the excited bending vibrations of the end of the rod is obtained, indicating the passage of vibrations through the fixing section of the finite length, which occurs due to the transformation of longitudinal vibrations in the loading zone into longitudinal-transverse-shear vibrations of the rod-strip in the fixing zone, followed by their transformation into predominantly bending vibrations of the cantilever part of the rod. For the theoretical study of the described phenomenon, a transformational model of deformation of the rod-strip is constructed, taking into account the deformability of the fastening section of finite length on the basis of the refined model of S. Timoshenko. The cantilever part of the rod is represented by the classical Kirchhoff-Love model, taking into account geometric nonlinearity in determining axial deformations. The kinematic conditions of coupling of the fixed and cantilever parts of the rod are formulated. On the basis of the Hamilton-Ostrogradsky variational equation, the equations of motion of the non-fixed and fixed parts of the rod, as well as the boundary conditions for them and the force condition of conjugation of the marked parts of the rod are obtained. Numerical experiments have been carried out for a rod-strip made of aluminum alloy D16AT, showing a noticeable passage of vibrations through the fixing section of the final length into the cantilever part of the rod with a decrease in the dynamic shear modulus of the material to a certain value.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"7 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059065","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"2D TOPOLOGICAL OPTIMIZATION WITH STATIC AND KINEMATIC EFFECTS","authors":"V.G. Kiselev, O.A. Sergeev, S.A. Sergeeva, E.I. Komarova","doi":"10.32326/1814-9146-2023-85-3-323-339","DOIUrl":"https://doi.org/10.32326/1814-9146-2023-85-3-323-339","url":null,"abstract":"Topological optimization of linearly elastic 2D structures under static and kinematic effects is presented. As an objective function, the compliance of the structure is considered, which is equal to the work of given external forces and displacements on the displacements and support forces caused by them. The design variables are the thicknesses of 2D finite elements. A constraint in the form of equality on a given volume of distributed material within a given design area is taken into account. The optimization method is based on optimality criteria. The examples consider the topological optimization of a simply supported beam and a cantilever beam under kinematic and static effects.The displacement is given instead of a concentrated force in the middle of simplysupported beam or at the free end of a cantilever beam. The simply supported beam was divided into 150 finite elements along the length and 50 finite elements along the height, the cantilever beam – into 150 finite elements along the lengthand 100 finite elements along the height. Differences between the results of optimization under kinematic effect and the results of optimization under static effect are insignificant. To conduct an experiment on biaxial tensionthe analysis considered a 2D sample consisting of a square test part of constant thickness and a square supporting part, which transmits an external force to the test part. The distribution of thicknesses of the providing part of a given volume was obtained, which minimizes its compliance.Under kinematic effect, the testing machine generates a unit displacement perpendicular to both ends of the specimen and a zero displacement along both edges of the supporting part.Under static effect, the testing machine created a uniform load along the edge of the supporting part in each node. It is shown t hat the sensitivity and the optimization process significantly depend on the type of external effect – static and kinematic.","PeriodicalId":496917,"journal":{"name":"Проблемы прочности и пластичности","volume":"137 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135059263","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}