Doszhan Yeleussinov, A. Assangaliyev, Assel Ospanova, V. Nagimov, Elena Kirpichikova, A. Makashev
{"title":"Vertical Fracture Monitoring by Multi-Rate Through-Barrier Diagnostics","authors":"Doszhan Yeleussinov, A. Assangaliyev, Assel Ospanova, V. Nagimov, Elena Kirpichikova, A. Makashev","doi":"10.2118/207067-ms","DOIUrl":"https://doi.org/10.2118/207067-ms","url":null,"abstract":"\u0000 Hydraulic fracturing has been demonstrated to be a cost-effective method of developing low-permeability heterogeneous clastic reservoirs with vertical wells. In the presence of a thin shale layer as a seal, monitoring effective fracture height becomes extremely important. The conventional approach of a single-regime production logging may be ineffective due to the complex geometry of fluid flow in the near-wellbore zone around the well. The paper describes the experience of the multi-rate through barrier diagnostics as a method of improving hydraulic fracturing evaluation. The standard way to diagnose the effectiveness of hydraulic fracturing is to log a survey under current operating conditions. In general, temperature and passive spectral acoustic measurements provide useful information on identifying the boundaries of fluid movement behind production casing; however, it is difficult to determine if flow occurs in the vertical hydraulic fracture or channeling through damaged cement in a single-regime survey. The multi-rate through-barrier diagnostics allow analyzing the flow dynamics of the wellbore-fracture-formation system under different flowing regimes, enabling a more accurate assessment of fluid movement in the near-wellbore environment within several meters. The paper includes the results of the multi-rate logging survey campaign in vertical water injection wells drilled in a low-permeability clastic reservoir. A proppant-based hydraulic fracturing of the target formation was carried out in the wells. The geological structure of the developed reservoir includes a thin shale layer (break) that separates the target oil-saturated interval from the overlying water bearing reservoir. In order for the operator to optimize future stimulation programs identification of effective hydraulic fracture height in reservoir regions with different shale thicknesses is crucial. The upper boundaries of the injected fluid movement behind the casing were determined based on the survey results. Analysis of the acoustic and temperature field dynamics helped more reliably evaluate the nature of the fluid movement behind the casing, whether flow happens in vertical fracture or cement channeling. This results in a more precise quantitative assessment of the injection profile in the targeted and untargeted reservoir units.","PeriodicalId":145609,"journal":{"name":"Day 3 Thu, October 07, 2021","volume":"248 6","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"132904409","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"A Workflow to Derive Rock Mechanics Correlations and Stress Profile by the Integration of Dynamic and Static Formation Evaluation Data","authors":"Ammar Qatari","doi":"10.2118/207030-ms","DOIUrl":"https://doi.org/10.2118/207030-ms","url":null,"abstract":"\u0000 Rock mechanics utilizes empirical formulas which are based on studies of certain environments. The shortcoming of such criteria is having estimations of rock physical properties with high uncertainty and not field/formation specific. The objective of this paper is to apply a core-log integration to convert dynamic mechanical properties captured from formation evaluation logs and calibrate them with core static data to generate a continuous profile of data with low uncertainty and generate correlations applicable to the specific physical environment.\u0000 To obtain proper rock mechanical correlations, building a mechanical earth model (MEM) calibrated with core data and stimulation data is essential. Multiple wells drilled in a certain sandstone field with rock mechanical physical tests are analyzed. Multi-arm caliber data is also put in use to establish knowledge about in-situ stress directions. The procedure starts with gathering and filtering acoustic slowness & shear, formation pressure, density, and oriented multi-arm caliper logs. Next, calibration of dynamic to core static mechanical data collected in the lab is established. The geomechanical analysis includes an understanding of the state of stresses in a chosen reservoir along with rock elastic and failure properties. The complied data is then integrated using different workflows to develop Mechanical Earth Model (MEM). The intended rock mechanics correlations include elastic constants (Young's Modulus and Poisson's ratio), and rock failure parameters. Once Mechanical Earth Model (MEM) is established, dynamic logging data and core static data are correlated to produce key rock mechanics elements that are field and formation specific. The correlations include Young's Modulus, Poisson's Ratio, Unconfined Compressive Strength (UCS) correlation, and Friction Angle (FANG) correlation. A range of each rock mechanic element is also highlighted for the specific environment showcasing the limits expected for collapse and fracture. Ultimately, stress profile is generated with low uncertainty highlighting magnitudes of maximum and minimum horizontal stresses along with the given interval.","PeriodicalId":145609,"journal":{"name":"Day 3 Thu, October 07, 2021","volume":"39 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130475220","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
V. Blinov, E. Koshevaya, Samat Ramatullayev, A. Filimonov, Kirill Shteynbrenner, M. Zhabagenov
{"title":"Exploration and Formation Testing of Low Permeability Clastic Reservoir in Hot Slim-Diameter Open-Hole Well","authors":"V. Blinov, E. Koshevaya, Samat Ramatullayev, A. Filimonov, Kirill Shteynbrenner, M. Zhabagenov","doi":"10.2118/207031-ms","DOIUrl":"https://doi.org/10.2118/207031-ms","url":null,"abstract":"\u0000 The objective of the logging campaign was to explore the hydrocarbon deposits in low-permeability clastic reservoirs utilizing an advanced logging suite and a high-tech wireline formation tester (WFT). The exploration well, which had a diameter of 146 mm and was drilled to a vertical depth of 4750 m, had a temperature of 147 degrees Celsius downhole.\u0000 Despite the challenging geological and downhole conditions: low permeability reservoir, high reservoir temperature, small wellbore diameter, and very high salinity drilling mud, the advanced logging suite data, which included nuclear magnetic resonance (NMR) and cross-dipole broadband acoustic logging, was successfully acquired. The WFT, which consists of a unique radial probe technology for efficient sampling of extremely low-permeability formations and a downhole fluid analyzer to determine the nature of the inflow and make rapid operational decisions in real time, was then used to perform downhole fluid analysis and sampling stations.\u0000 Oil and gas-saturated reservoir intervals were identified, their porosity, water saturation, and permeability were evaluated, and an optimal open hole WFT program was produced as a result of the extended logging suite's interpretation. Special technological operations were performed during well logging in this well, allowing for the acquisition of high-quality NMR data under extreme conditions. Rapid processing and interpretation of well logging data, performed without any a priori reservoir data, allowing for the identification of the best permeability intervals in oil and gas-saturated reservoirs and the design of an optimal WFT program in an open hole. Downhole fluid analysis and sampling stations were performed with WFT with pressure build-up to determine fluid mobility to validate the presence of productive intervals. Thus, in several downhole trips in a relatively short period of time, potential hydrocarbon layers were assessed in an open hole section, and in the presence of sufficient fluid mobility, the saturation of the interval was determined by WFT. It is important to note that downhole gas samples were acquired in intervals having fluid mobility less than 0.06 mD/cP, where the conventional well test would most probably fail to induce a flow without stimulation.\u0000 An integrated approach using modern well logging methods made it possible to solve the set geological challenges in the extreme conditions in this exploration well, where traditional methods would introduce significant uncertainties.","PeriodicalId":145609,"journal":{"name":"Day 3 Thu, October 07, 2021","volume":"1 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129074413","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Artem Galimzyanov, Orkhan Heydarov, Bakhtiyar Jafarov, Rufat Mirzayev, Kamal Kamalov, A. Kilic
{"title":"Offshore Caspian Sea: Appraisal Well Monitoring Using Inflow Tracer Technology","authors":"Artem Galimzyanov, Orkhan Heydarov, Bakhtiyar Jafarov, Rufat Mirzayev, Kamal Kamalov, A. Kilic","doi":"10.2118/207065-ms","DOIUrl":"https://doi.org/10.2118/207065-ms","url":null,"abstract":"\u0000 A gas condensate field development in the offshore Caspian Sea experienced monitoring challenges and costly operations. In regular field-wide surveillance it is a challenging task to evaluate the numerous well monitoring options on the market, such as production logging, permanent downhole gauges, and distributed temperature sensing along the wellbore. These solutions require wellbore interventions and introduce operational risk during well logging or completion installation risk when fiber is installed. Permanently installed inflow tracer technology is an alternative monitoring solution which avoids the above-mentioned risks but still obtain valuable inflow information concerning well performance over several years.\u0000 An appraisal well in the field was selected to pilot inflow tracing technology for assessment of reserves and productivity, for the first time in the Caspian Sea. Multiple sampling campaigns to capture the data was incorporated into a well testing programme to complement the pressure transient data collection and interpretation. The inflow tracer interpretations were successful in providing additional insight towards clean-up efficiency and flow distribution between zones. The latter was verified later by production logging, strengthening confidence with inflow tracer technology.\u0000 The application of the permanent inflow tracers has proven to be a viable alternative to other well monitoring solutions without any risk and will become an effective long-term monitoring solution for planned production wells in the field development.","PeriodicalId":145609,"journal":{"name":"Day 3 Thu, October 07, 2021","volume":"117 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129979378","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Chingis Oshakbayev, Roman M. Romanov, Valentin Vlassenko, S. Austin, Sergey Kovalev, S. Shatalov, Rostislav Platonov, Aidos Osipov
{"title":"Combined Application of Deep Boundary Detection Tool, Multilayer Data Inversion and 3D Visualization of Seismic Data in Real Time for Geosteering on the Oilfield in the Russian Federation","authors":"Chingis Oshakbayev, Roman M. Romanov, Valentin Vlassenko, S. Austin, Sergey Kovalev, S. Shatalov, Rostislav Platonov, Aidos Osipov","doi":"10.2118/207035-ms","DOIUrl":"https://doi.org/10.2118/207035-ms","url":null,"abstract":"\u0000 Currently drilling of horizontal wells is a common enhanced oil recovery method. Geosteering services are often used for accurate well placement, which makes it possible to achieve a significant increase in production at relatively low cost.\u0000 This paper describes the result of using seismic data in three-dimensional visualization for high-quality geosteering using a deep boundary detection tool and multilayer inversion in real time.\u0000 Crossing the top of the reservoir while drilling horizontal sections at the current oilfield is unacceptable, due to the presence of reactive mudstones. In case of crossing the top of reservoir, further work on running and installing the liner becomes impossible due to instability and may lead to well collapse.\u0000 Based on prewell analysis of the structural data, the well was not supposed to approach the top of the target formation along the planned profile. However, while preparing geosteering model and analyzing seismic data it became possible to reveal that risk, elaborate its mitigation and eventually increase the length of the horizontal section.\u0000 Such integrated analysis made it possible to maintain the wellbore within the target reservoirs, as well as to update the structural bedding of the top based on the multilayer inversion results.","PeriodicalId":145609,"journal":{"name":"Day 3 Thu, October 07, 2021","volume":"577 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127069236","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
{"title":"Nano Composite Polymer Composition for Water Shutoff Treatment at High Formation Temperature","authors":"A. B. Suleymanov, A. D. Shovgenov","doi":"10.2118/207066-ms","DOIUrl":"https://doi.org/10.2118/207066-ms","url":null,"abstract":"\u0000 Excess water production cause serious technical and economic issues including corrosion, loss of productivity, scaling and etc. Various chemical and mechanical methods have been developed to isolate water source in the formation. Among chemical methods polymer-gel treatment is one of the proven solutions in which gel block is placed into high permeable water channel in order to isolate the water source. Most common polymer that is used for water shut-off treatments is Polyacrylamide (PAM) due to its availability and low cost. However in harsh reservoir conditions stability of gel based on PAM is unsatisfactory. Present study focuses on enhancement of bulk gel composition by addition of nano Silica. The effect of nano Silica on gel properties such as gel stability, strength, gelation time, bound/free water content, residual resistance factor was investigated. The results shows that nano Silica addition into bulk gel shortens the gelation time and strengthens the gel. Addition of nano silica significantly reduces syneresis of the gel and nano silica significantly improves the blocking ability of the gel by strengthening the bulk gel and increasing the adsorption. Furthermore, even after aging at 105 °C for 30 days the RRF for the gel with 1% nano silica is still sufficiently high. This observation is explained by syneresis decrement of bulk gel caused by nano Silica.","PeriodicalId":145609,"journal":{"name":"Day 3 Thu, October 07, 2021","volume":"18 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2021-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"117064468","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}