基体变量对热喷涂涂层界面断裂能的影响

IF 5.3 2区 材料科学 Q1 MATERIALS SCIENCE, COATINGS & FILMS
Saim Abbas , Sanjay Sampath , Sudhanshu Mallick , B. Nagamani Jaya
{"title":"基体变量对热喷涂涂层界面断裂能的影响","authors":"Saim Abbas ,&nbsp;Sanjay Sampath ,&nbsp;Sudhanshu Mallick ,&nbsp;B. Nagamani Jaya","doi":"10.1016/j.surfcoat.2025.132237","DOIUrl":null,"url":null,"abstract":"<div><div>The effects of substrate material, substrate roughness and substrate thickness on the interface fracture energy (<em>G</em><sub><em>C</em></sub>) of thermal spray coating/metallic substrate interfaces are determined. Air Plasma Sprayed (APS) coatings of Yttria Stabilized Zirconia (YSZ) and Alumina, as well as NiCrAlY are investigated with different substrate materials (stainless steel-SS, mild steel-MS), roughness and thickness. Modified cantilever beam bending with Digital Image Correlation (DIC) based tracking of crack length is used for high-throughput measurements. A 46 % increase in <em>G</em><sub><em>C</em></sub> is seen due to an increase of 73 % substrate roughness (<em>R</em><sub><em>a</em></sub>) of substrate for YSZ/SS, while a 60 % increase in <em>G</em><sub><em>C</em></sub> is seen due to an increase in 166 % <em>R</em><sub><em>a</em></sub> of substrate for Alumina/MS system. Interface fracture energy <em>G</em><sub><em>C</em></sub> of YSZ/MS is found to be ∼75 <em>J/m</em><sup><em>2</em></sup>, compared to ∼50 <em>J/m</em><sup><em>2</em></sup> for the Alumina/MS for similar coating/substrate thickness as well as substrate roughness. For the same coating type and thickness of YSZ, <em>G</em><sub><em>C</em></sub> decreased to 60 <em>J/m</em><sup><em>2</em></sup> when the substrate was changed to SS, even with an increase in <em>R</em><sub><em>a</em></sub>. This could be attributed to the significant effect of residual stress, originating from thermal expansion mismatch, with higher compressive residual stresses increasing the propensity for interfacial delamination. There is no effect of substrate thickness on <em>G</em><sub><em>C</em></sub>, independent of whether the substrate is machined before or after the deposition. Mechanisms of these changes are discussed in the context of total interface fracture area and crack closure stresses.</div></div>","PeriodicalId":22009,"journal":{"name":"Surface & Coatings Technology","volume":"510 ","pages":"Article 132237"},"PeriodicalIF":5.3000,"publicationDate":"2025-05-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Effect of substrate variables on the interface fracture energy of thermal spray coatings\",\"authors\":\"Saim Abbas ,&nbsp;Sanjay Sampath ,&nbsp;Sudhanshu Mallick ,&nbsp;B. Nagamani Jaya\",\"doi\":\"10.1016/j.surfcoat.2025.132237\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<div><div>The effects of substrate material, substrate roughness and substrate thickness on the interface fracture energy (<em>G</em><sub><em>C</em></sub>) of thermal spray coating/metallic substrate interfaces are determined. Air Plasma Sprayed (APS) coatings of Yttria Stabilized Zirconia (YSZ) and Alumina, as well as NiCrAlY are investigated with different substrate materials (stainless steel-SS, mild steel-MS), roughness and thickness. Modified cantilever beam bending with Digital Image Correlation (DIC) based tracking of crack length is used for high-throughput measurements. A 46 % increase in <em>G</em><sub><em>C</em></sub> is seen due to an increase of 73 % substrate roughness (<em>R</em><sub><em>a</em></sub>) of substrate for YSZ/SS, while a 60 % increase in <em>G</em><sub><em>C</em></sub> is seen due to an increase in 166 % <em>R</em><sub><em>a</em></sub> of substrate for Alumina/MS system. Interface fracture energy <em>G</em><sub><em>C</em></sub> of YSZ/MS is found to be ∼75 <em>J/m</em><sup><em>2</em></sup>, compared to ∼50 <em>J/m</em><sup><em>2</em></sup> for the Alumina/MS for similar coating/substrate thickness as well as substrate roughness. For the same coating type and thickness of YSZ, <em>G</em><sub><em>C</em></sub> decreased to 60 <em>J/m</em><sup><em>2</em></sup> when the substrate was changed to SS, even with an increase in <em>R</em><sub><em>a</em></sub>. This could be attributed to the significant effect of residual stress, originating from thermal expansion mismatch, with higher compressive residual stresses increasing the propensity for interfacial delamination. There is no effect of substrate thickness on <em>G</em><sub><em>C</em></sub>, independent of whether the substrate is machined before or after the deposition. Mechanisms of these changes are discussed in the context of total interface fracture area and crack closure stresses.</div></div>\",\"PeriodicalId\":22009,\"journal\":{\"name\":\"Surface & Coatings Technology\",\"volume\":\"510 \",\"pages\":\"Article 132237\"},\"PeriodicalIF\":5.3000,\"publicationDate\":\"2025-05-04\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Surface & Coatings Technology\",\"FirstCategoryId\":\"88\",\"ListUrlMain\":\"https://www.sciencedirect.com/science/article/pii/S0257897225005110\",\"RegionNum\":2,\"RegionCategory\":\"材料科学\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q1\",\"JCRName\":\"MATERIALS SCIENCE, COATINGS & FILMS\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Surface & Coatings Technology","FirstCategoryId":"88","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S0257897225005110","RegionNum":2,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q1","JCRName":"MATERIALS SCIENCE, COATINGS & FILMS","Score":null,"Total":0}
引用次数: 0

摘要

确定了基体材料、基体粗糙度和基体厚度对热喷涂涂层/金属基体界面断裂能(GC)的影响。采用不同的基体材料(不锈钢- ss、低碳钢- ms)、粗糙度和厚度,研究了氧化钇稳定氧化锆(YSZ)、氧化铝和NiCrAlY的空气等离子喷涂(APS)涂层。改进悬臂梁弯曲与数字图像相关(DIC)为基础的裂纹长度跟踪用于高通量测量。由于YSZ/SS的基体粗糙度(Ra)增加了73%,GC增加了46%,而氧化铝/质谱系统的基体Ra增加了166%,GC增加了60%。发现YSZ/MS的界面断裂能GC为~ 75 J/m2,而氧化铝/MS的界面断裂能GC为~ 50 J/m2,涂层/衬底厚度和衬底粗糙度相似。对于相同涂层类型和厚度的YSZ,当基体改为SS时,即使Ra增加,GC也下降到60 J/m2。这可能是由于热膨胀失配引起的残余应力的显著影响,较高的压残余应力增加了界面分层的倾向。衬底厚度对GC没有影响,与衬底是在沉积之前还是之后加工无关。从界面总断裂面积和裂纹闭合应力的角度讨论了这些变化的机理。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
Effect of substrate variables on the interface fracture energy of thermal spray coatings
The effects of substrate material, substrate roughness and substrate thickness on the interface fracture energy (GC) of thermal spray coating/metallic substrate interfaces are determined. Air Plasma Sprayed (APS) coatings of Yttria Stabilized Zirconia (YSZ) and Alumina, as well as NiCrAlY are investigated with different substrate materials (stainless steel-SS, mild steel-MS), roughness and thickness. Modified cantilever beam bending with Digital Image Correlation (DIC) based tracking of crack length is used for high-throughput measurements. A 46 % increase in GC is seen due to an increase of 73 % substrate roughness (Ra) of substrate for YSZ/SS, while a 60 % increase in GC is seen due to an increase in 166 % Ra of substrate for Alumina/MS system. Interface fracture energy GC of YSZ/MS is found to be ∼75 J/m2, compared to ∼50 J/m2 for the Alumina/MS for similar coating/substrate thickness as well as substrate roughness. For the same coating type and thickness of YSZ, GC decreased to 60 J/m2 when the substrate was changed to SS, even with an increase in Ra. This could be attributed to the significant effect of residual stress, originating from thermal expansion mismatch, with higher compressive residual stresses increasing the propensity for interfacial delamination. There is no effect of substrate thickness on GC, independent of whether the substrate is machined before or after the deposition. Mechanisms of these changes are discussed in the context of total interface fracture area and crack closure stresses.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
Surface & Coatings Technology
Surface & Coatings Technology 工程技术-材料科学:膜
CiteScore
10.00
自引率
11.10%
发文量
921
审稿时长
19 days
期刊介绍: Surface and Coatings Technology is an international archival journal publishing scientific papers on significant developments in surface and interface engineering to modify and improve the surface properties of materials for protection in demanding contact conditions or aggressive environments, or for enhanced functional performance. Contributions range from original scientific articles concerned with fundamental and applied aspects of research or direct applications of metallic, inorganic, organic and composite coatings, to invited reviews of current technology in specific areas. Papers submitted to this journal are expected to be in line with the following aspects in processes, and properties/performance: A. Processes: Physical and chemical vapour deposition techniques, thermal and plasma spraying, surface modification by directed energy techniques such as ion, electron and laser beams, thermo-chemical treatment, wet chemical and electrochemical processes such as plating, sol-gel coating, anodization, plasma electrolytic oxidation, etc., but excluding painting. B. Properties/performance: friction performance, wear resistance (e.g., abrasion, erosion, fretting, etc), corrosion and oxidation resistance, thermal protection, diffusion resistance, hydrophilicity/hydrophobicity, and properties relevant to smart materials behaviour and enhanced multifunctional performance for environmental, energy and medical applications, but excluding device aspects.
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
确定
请完成安全验证×
copy
已复制链接
快去分享给好友吧!
我知道了
右上角分享
点击右上角分享
0
联系我们:info@booksci.cn Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。 Copyright © 2023 布克学术 All rights reserved.
京ICP备2023020795号-1
ghs 京公网安备 11010802042870号
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术官方微信