氧-乙炔火焰热冲击下空气等离子喷涂（掺钆、掺镱）YSZ隔热涂层的裂纹行为和失效机理

IF 5.1 2区材料科学 Q1 MATERIALS SCIENCE, CERAMICS

Ceramics International Pub Date : 2024-10-01 DOI:10.1016/j.ceramint.2024.09.417

Zheng Zhao , Junmiao Shi , Wenhu Xu , Xiaolong Chen , Kehan Yang , Fuqiang Tian , Xiancheng Zhang

{"title":"氧-乙炔火焰热冲击下空气等离子喷涂（掺钆、掺镱）YSZ隔热涂层的裂纹行为和失效机理","authors":"Zheng Zhao , Junmiao Shi , Wenhu Xu , Xiaolong Chen , Kehan Yang , Fuqiang Tian , Xiancheng Zhang","doi":"10.1016/j.ceramint.2024.09.417","DOIUrl":null,"url":null,"abstract":"<div><div>This paper examines the performance and failure mechanisms of atmospheric plasma sprayed (Gd, Yb)-doped YSZ (RYSZ) thermal barrier coatings (TBCs) under oxy-acetylene flame thermal shock conditions. The study involved cyclic thermal shock testing at temperatures of 1400 °C, 1500 °C, and 1600 °C for 10-min intervals until failure occurred, with failure counts recorded as 6, 2, and 2, respectively. During the thermal shock tests, tensile stress in the top coat (TC) caused vertical cracks. The growth of the thermally grown oxide (TGO) layer concentrated stress at the top coat/bond coat interface, leading to transverse interfacial cracks. As the shock temperature increased, the density of vertical cracks and the length of transverse interfacial cracks also increased. Additionally, transverse cracks developed in the TC due to sintering of the surface region at higher shock temperatures. The interaction between vertical and transverse cracks was critical to the spalling of the TC. Variations in crack densities and lengths resulted in different failure modes of the TBCs, depending on the thermal shock temperatures (1400 °C, 1500 °C, and 1600 °C).</div></div>","PeriodicalId":267,"journal":{"name":"Ceramics International","volume":"50 23","pages":"Pages 50726-50737"},"PeriodicalIF":5.1000,"publicationDate":"2024-10-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Crack behaviour and failure mechanisms of air plasma sprayed (Gd, Yb) doped YSZ thermal barrier coatings under oxy-acetylene flame thermal shock\",\"authors\":\"Zheng Zhao , Junmiao Shi , Wenhu Xu , Xiaolong Chen , Kehan Yang , Fuqiang Tian , Xiancheng Zhang\",\"doi\":\"10.1016/j.ceramint.2024.09.417\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<div><div>This paper examines the performance and failure mechanisms of atmospheric plasma sprayed (Gd, Yb)-doped YSZ (RYSZ) thermal barrier coatings (TBCs) under oxy-acetylene flame thermal shock conditions. The study involved cyclic thermal shock testing at temperatures of 1400 °C, 1500 °C, and 1600 °C for 10-min intervals until failure occurred, with failure counts recorded as 6, 2, and 2, respectively. During the thermal shock tests, tensile stress in the top coat (TC) caused vertical cracks. The growth of the thermally grown oxide (TGO) layer concentrated stress at the top coat/bond coat interface, leading to transverse interfacial cracks. As the shock temperature increased, the density of vertical cracks and the length of transverse interfacial cracks also increased. Additionally, transverse cracks developed in the TC due to sintering of the surface region at higher shock temperatures. The interaction between vertical and transverse cracks was critical to the spalling of the TC. Variations in crack densities and lengths resulted in different failure modes of the TBCs, depending on the thermal shock temperatures (1400 °C, 1500 °C, and 1600 °C).</div></div>\",\"PeriodicalId\":267,\"journal\":{\"name\":\"Ceramics International\",\"volume\":\"50 23\",\"pages\":\"Pages 50726-50737\"},\"PeriodicalIF\":5.1000,\"publicationDate\":\"2024-10-01\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Ceramics International\",\"FirstCategoryId\":\"88\",\"ListUrlMain\":\"https://www.sciencedirect.com/science/article/pii/S0272884224044523\",\"RegionNum\":2,\"RegionCategory\":\"材料科学\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q1\",\"JCRName\":\"MATERIALS SCIENCE, CERAMICS\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Ceramics International","FirstCategoryId":"88","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S0272884224044523","RegionNum":2,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q1","JCRName":"MATERIALS SCIENCE, CERAMICS","Score":null,"Total":0}

引用次数: 0

摘要

本文研究了常压等离子喷涂（钆、镱）掺杂 YSZ（RYSZ）隔热涂层（TBC）在氧-乙炔焰热冲击条件下的性能和失效机理。研究包括在 1400 ℃、1500 ℃ 和 1600 ℃ 温度下进行循环热冲击测试，每隔 10 分钟测试一次，直至涂层失效，失效次数分别为 6、2 和 2。在热冲击试验过程中，表层（TC）的拉伸应力导致垂直裂纹。热生长氧化物 (TGO) 层的生长将应力集中在面层/粘合层界面上，导致横向界面裂纹。随着冲击温度的升高，垂直裂纹的密度和横向界面裂纹的长度也在增加。此外，在冲击温度较高时，由于表面区域烧结，TC 中也出现了横向裂纹。垂直裂缝和横向裂缝之间的相互作用对 TC 的剥落至关重要。根据热冲击温度（1400 ℃、1500 ℃ 和 1600 ℃）的不同，裂纹密度和长度的变化导致了 TBC 的不同失效模式。

本文章由计算机程序翻译，如有差异，请以英文原文为准。

查看原文本刊更多论文

Crack behaviour and failure mechanisms of air plasma sprayed (Gd, Yb) doped YSZ thermal barrier coatings under oxy-acetylene flame thermal shock

This paper examines the performance and failure mechanisms of atmospheric plasma sprayed (Gd, Yb)-doped YSZ (RYSZ) thermal barrier coatings (TBCs) under oxy-acetylene flame thermal shock conditions. The study involved cyclic thermal shock testing at temperatures of 1400 °C, 1500 °C, and 1600 °C for 10-min intervals until failure occurred, with failure counts recorded as 6, 2, and 2, respectively. During the thermal shock tests, tensile stress in the top coat (TC) caused vertical cracks. The growth of the thermally grown oxide (TGO) layer concentrated stress at the top coat/bond coat interface, leading to transverse interfacial cracks. As the shock temperature increased, the density of vertical cracks and the length of transverse interfacial cracks also increased. Additionally, transverse cracks developed in the TC due to sintering of the surface region at higher shock temperatures. The interaction between vertical and transverse cracks was critical to the spalling of the TC. Variations in crack densities and lengths resulted in different failure modes of the TBCs, depending on the thermal shock temperatures (1400 °C, 1500 °C, and 1600 °C).

求助全文

通过发布文献求助，成功后即可免费获取论文全文。去求助

来源期刊

Ceramics International 工程技术-材料科学：硅酸盐

CiteScore

9.40

自引率

15.40%

发文量

4558

审稿时长

25 days

期刊介绍： Ceramics International covers the science of advanced ceramic materials. The journal encourages contributions that demonstrate how an understanding of the basic chemical and physical phenomena may direct materials design and stimulate ideas for new or improved processing techniques, in order to obtain materials with desired structural features and properties. Ceramics International covers oxide and non-oxide ceramics, functional glasses, glass ceramics, amorphous inorganic non-metallic materials (and their combinations with metal and organic materials), in the form of particulates, dense or porous bodies, thin/thick films and laminated, graded and composite structures. Process related topics such as ceramic-ceramic joints or joining ceramics with dissimilar materials, as well as surface finishing and conditioning are also covered. Besides traditional processing techniques, manufacturing routes of interest include innovative procedures benefiting from externally applied stresses, electromagnetic fields and energetic beams, as well as top-down and self-assembly nanotechnology approaches. In addition, the journal welcomes submissions on bio-inspired and bio-enabled materials designs, experimentally validated multi scale modelling and simulation for materials design, and the use of the most advanced chemical and physical characterization techniques of structure, properties and behaviour. Technologically relevant low-dimensional systems are a particular focus of Ceramics International. These include 0, 1 and 2-D nanomaterials (also covering CNTs, graphene and related materials, and diamond-like carbons), their nanocomposites, as well as nano-hybrids and hierarchical multifunctional nanostructures that might integrate molecular, biological and electronic components.