α、α+β 和 β 钛合金与钢的摩擦学行为综合研究

IF 5.3 1区工程技术 Q1 ENGINEERING, MECHANICAL

Wear Pub Date : 2024-10-18 DOI:10.1016/j.wear.2024.205595

Tania Sola , Pierre Maurel , Laurent Weiss , Eric Fleury , Thierry Grosdidier

{"title":"α、α+β 和 β 钛合金与钢的摩擦学行为综合研究","authors":"Tania Sola , Pierre Maurel , Laurent Weiss , Eric Fleury , Thierry Grosdidier","doi":"10.1016/j.wear.2024.205595","DOIUrl":null,"url":null,"abstract":"<div><div>The tribological behaviour of three different natures of titanium alloys, the α (T50), α+β (Ti-6Al-4V) and β (Ti-5553), against a steel ball counterpart was investigated for different surface conditions produced by surface severe plastic deformation (SSPD) at room and cryogenic temperatures.</div><div>Friction led to the formation of various oxides that acted as third bodies and resulted in different wear regimes referred to as stages I, II, and III. Stage I, the initial abrasive regime under which TiO<sub>2</sub>-anatase formed, was the only characteristic of the β Ti-5553 alloy behaviour. In addition, stages II and III were observed for the α T50 and α+β Ti-6Al-4V alloys. Stage II is characterised by an increase in the coefficient of friction (COF) associated with the formation of hard TiO<sub>2</sub>-rutile. Stage III corresponds to the formation of Fe-oxides induced by the steel ball abrasion. While the COF remained steady during stage III for T50, the presence of β-phase in the Ti-6Al-4V destabilised periodically the Fe-oxide layer during stage III and generated repeated sharp drops in the COF values.</div><div>Despite increasing hardness and roughness of the treated surfaces, SSPD did not modify the overall mechanisms of abrasion and improved only slightly the tribological properties.</div></div>","PeriodicalId":23970,"journal":{"name":"Wear","volume":"560 ","pages":"Article 205595"},"PeriodicalIF":5.3000,"publicationDate":"2024-10-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"A comprehensive investigation of the tribological behaviour of α, α+β, and β titanium alloys against a steel counterpart\",\"authors\":\"Tania Sola , Pierre Maurel , Laurent Weiss , Eric Fleury , Thierry Grosdidier\",\"doi\":\"10.1016/j.wear.2024.205595\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<div><div>The tribological behaviour of three different natures of titanium alloys, the α (T50), α+β (Ti-6Al-4V) and β (Ti-5553), against a steel ball counterpart was investigated for different surface conditions produced by surface severe plastic deformation (SSPD) at room and cryogenic temperatures.</div><div>Friction led to the formation of various oxides that acted as third bodies and resulted in different wear regimes referred to as stages I, II, and III. Stage I, the initial abrasive regime under which TiO<sub>2</sub>-anatase formed, was the only characteristic of the β Ti-5553 alloy behaviour. In addition, stages II and III were observed for the α T50 and α+β Ti-6Al-4V alloys. Stage II is characterised by an increase in the coefficient of friction (COF) associated with the formation of hard TiO<sub>2</sub>-rutile. Stage III corresponds to the formation of Fe-oxides induced by the steel ball abrasion. While the COF remained steady during stage III for T50, the presence of β-phase in the Ti-6Al-4V destabilised periodically the Fe-oxide layer during stage III and generated repeated sharp drops in the COF values.</div><div>Despite increasing hardness and roughness of the treated surfaces, SSPD did not modify the overall mechanisms of abrasion and improved only slightly the tribological properties.</div></div>\",\"PeriodicalId\":23970,\"journal\":{\"name\":\"Wear\",\"volume\":\"560 \",\"pages\":\"Article 205595\"},\"PeriodicalIF\":5.3000,\"publicationDate\":\"2024-10-18\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Wear\",\"FirstCategoryId\":\"5\",\"ListUrlMain\":\"https://www.sciencedirect.com/science/article/pii/S0043164824003600\",\"RegionNum\":1,\"RegionCategory\":\"工程技术\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q1\",\"JCRName\":\"ENGINEERING, MECHANICAL\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Wear","FirstCategoryId":"5","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S0043164824003600","RegionNum":1,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q1","JCRName":"ENGINEERING, MECHANICAL","Score":null,"Total":0}

引用次数: 0

摘要

研究了三种不同性质的钛合金--α（T50）、α+β（Ti-6Al-4V）和β（Ti-5553）--在室温和低温下通过表面剧烈塑性变形（SSPD）产生的不同表面条件下与钢球的摩擦学行为。阶段 I 是形成 TiO2-anatase 的初始磨损状态，是 β Ti-5553 合金行为的唯一特征。此外，在 α T50 和 α+β Ti-6Al-4V 合金中还观察到第二和第三阶段。第二阶段的特点是摩擦系数（COF）的增加与硬质 TiO2-Rutile 的形成有关。第三阶段与钢球磨损引起的铁氧化物的形成相对应。虽然 T50 的 COF 在第三阶段保持稳定，但 Ti-6Al-4V 中存在的 β 相在第三阶段周期性地破坏了氧化铁层的稳定性，并导致 COF 值反复急剧下降。

本文章由计算机程序翻译，如有差异，请以英文原文为准。

A comprehensive investigation of the tribological behaviour of α, α+β, and β titanium alloys against a steel counterpart

查看原文本刊更多论文

A comprehensive investigation of the tribological behaviour of α, α+β, and β titanium alloys against a steel counterpart

The tribological behaviour of three different natures of titanium alloys, the α (T50), α+β (Ti-6Al-4V) and β (Ti-5553), against a steel ball counterpart was investigated for different surface conditions produced by surface severe plastic deformation (SSPD) at room and cryogenic temperatures.

Friction led to the formation of various oxides that acted as third bodies and resulted in different wear regimes referred to as stages I, II, and III. Stage I, the initial abrasive regime under which TiO₂-anatase formed, was the only characteristic of the β Ti-5553 alloy behaviour. In addition, stages II and III were observed for the α T50 and α+β Ti-6Al-4V alloys. Stage II is characterised by an increase in the coefficient of friction (COF) associated with the formation of hard TiO₂-rutile. Stage III corresponds to the formation of Fe-oxides induced by the steel ball abrasion. While the COF remained steady during stage III for T50, the presence of β-phase in the Ti-6Al-4V destabilised periodically the Fe-oxide layer during stage III and generated repeated sharp drops in the COF values.

Despite increasing hardness and roughness of the treated surfaces, SSPD did not modify the overall mechanisms of abrasion and improved only slightly the tribological properties.

求助全文

通过发布文献求助，成功后即可免费获取论文全文。去求助

来源期刊

Wear 工程技术-材料科学：综合

CiteScore

8.80

自引率

8.00%

发文量

280

审稿时长

47 days

期刊介绍： Wear journal is dedicated to the advancement of basic and applied knowledge concerning the nature of wear of materials. Broadly, topics of interest range from development of fundamental understanding of the mechanisms of wear to innovative solutions to practical engineering problems. Authors of experimental studies are expected to comment on the repeatability of the data, and whenever possible, conduct multiple measurements under similar testing conditions. Further, Wear embraces the highest standards of professional ethics, and the detection of matching content, either in written or graphical form, from other publications by the current authors or by others, may result in rejection.