Daniel Yoon , Kevin N. Eckstein , Margrethe Ruding , Philip V. Bayly
{"title":"三维打印水凝胶晶格中各向异性力学性能的结构调整","authors":"Daniel Yoon , Kevin N. Eckstein , Margrethe Ruding , Philip V. Bayly","doi":"10.1016/j.jmbbm.2024.106625","DOIUrl":null,"url":null,"abstract":"<div><p>We investigated the ability to tune the anisotropic mechanical properties of 3D-printed hydrogel lattices by modifying their geometry (lattice strut diameter, unit cell size, and unit cell scaling factor). Many soft tissues are anisotropic and the ability to mimic natural anisotropy would be valuable for developing tissue-surrogate “phantoms” for elasticity imaging (shear wave elastography or magnetic resonance elastography). Vintile lattices were 3D-printed in polyethylene glycol di-acrylate (PEGDA) using digital light projection printing. Two mechanical benchtop tests, dynamic shear testing and unconfined compression, were used to measure the apparent shear storage moduli (G′) and apparent Young's moduli (E) of lattice samples. Increasing the unit cell size from 1.25 mm to 2.00 mm reduced the Young's and shear moduli of the lattices by 91% and 85%, respectively. Decreasing the strut diameter from 300 μm to 200 μm reduced the apparent shear moduli of the lattices by 95%. Increasing the geometric scaling ratio of the lattice unit cells from 1.00 × to 2.00 × increased mechanical anisotropy in shear (by a factor of 3.1) and in compression (by a factor of 2.9). Both simulations and experiments show that the effects of unit cell size and strut diameter are consistent with power law relationships between volume fraction and apparent elastic moduli. In particular, experimental measurements of apparent Young's moduli agree well with predictions of the theoretical Gibson-Ashby model. Thus, the anisotropic mechanical properties of a lattice can be tuned by the unit cell size, the strut diameter, and scaling factors. This approach will be valuable in designing tissue-mimicking hydrogel lattice-based composite materials for elastography phantoms and tissue engineered scaffolds.</p></div>","PeriodicalId":380,"journal":{"name":"Journal of the Mechanical Behavior of Biomedical Materials","volume":null,"pages":null},"PeriodicalIF":3.3000,"publicationDate":"2024-06-14","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Structural tuning of anisotropic mechanical properties in 3D-Printed hydrogel lattices\",\"authors\":\"Daniel Yoon , Kevin N. Eckstein , Margrethe Ruding , Philip V. Bayly\",\"doi\":\"10.1016/j.jmbbm.2024.106625\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<div><p>We investigated the ability to tune the anisotropic mechanical properties of 3D-printed hydrogel lattices by modifying their geometry (lattice strut diameter, unit cell size, and unit cell scaling factor). Many soft tissues are anisotropic and the ability to mimic natural anisotropy would be valuable for developing tissue-surrogate “phantoms” for elasticity imaging (shear wave elastography or magnetic resonance elastography). Vintile lattices were 3D-printed in polyethylene glycol di-acrylate (PEGDA) using digital light projection printing. Two mechanical benchtop tests, dynamic shear testing and unconfined compression, were used to measure the apparent shear storage moduli (G′) and apparent Young's moduli (E) of lattice samples. Increasing the unit cell size from 1.25 mm to 2.00 mm reduced the Young's and shear moduli of the lattices by 91% and 85%, respectively. Decreasing the strut diameter from 300 μm to 200 μm reduced the apparent shear moduli of the lattices by 95%. Increasing the geometric scaling ratio of the lattice unit cells from 1.00 × to 2.00 × increased mechanical anisotropy in shear (by a factor of 3.1) and in compression (by a factor of 2.9). Both simulations and experiments show that the effects of unit cell size and strut diameter are consistent with power law relationships between volume fraction and apparent elastic moduli. In particular, experimental measurements of apparent Young's moduli agree well with predictions of the theoretical Gibson-Ashby model. Thus, the anisotropic mechanical properties of a lattice can be tuned by the unit cell size, the strut diameter, and scaling factors. This approach will be valuable in designing tissue-mimicking hydrogel lattice-based composite materials for elastography phantoms and tissue engineered scaffolds.</p></div>\",\"PeriodicalId\":380,\"journal\":{\"name\":\"Journal of the Mechanical Behavior of Biomedical Materials\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":3.3000,\"publicationDate\":\"2024-06-14\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Journal of the Mechanical Behavior of Biomedical Materials\",\"FirstCategoryId\":\"5\",\"ListUrlMain\":\"https://www.sciencedirect.com/science/article/pii/S1751616124002571\",\"RegionNum\":2,\"RegionCategory\":\"医学\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q2\",\"JCRName\":\"ENGINEERING, BIOMEDICAL\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Journal of the Mechanical Behavior of Biomedical Materials","FirstCategoryId":"5","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S1751616124002571","RegionNum":2,"RegionCategory":"医学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q2","JCRName":"ENGINEERING, BIOMEDICAL","Score":null,"Total":0}
Structural tuning of anisotropic mechanical properties in 3D-Printed hydrogel lattices
We investigated the ability to tune the anisotropic mechanical properties of 3D-printed hydrogel lattices by modifying their geometry (lattice strut diameter, unit cell size, and unit cell scaling factor). Many soft tissues are anisotropic and the ability to mimic natural anisotropy would be valuable for developing tissue-surrogate “phantoms” for elasticity imaging (shear wave elastography or magnetic resonance elastography). Vintile lattices were 3D-printed in polyethylene glycol di-acrylate (PEGDA) using digital light projection printing. Two mechanical benchtop tests, dynamic shear testing and unconfined compression, were used to measure the apparent shear storage moduli (G′) and apparent Young's moduli (E) of lattice samples. Increasing the unit cell size from 1.25 mm to 2.00 mm reduced the Young's and shear moduli of the lattices by 91% and 85%, respectively. Decreasing the strut diameter from 300 μm to 200 μm reduced the apparent shear moduli of the lattices by 95%. Increasing the geometric scaling ratio of the lattice unit cells from 1.00 × to 2.00 × increased mechanical anisotropy in shear (by a factor of 3.1) and in compression (by a factor of 2.9). Both simulations and experiments show that the effects of unit cell size and strut diameter are consistent with power law relationships between volume fraction and apparent elastic moduli. In particular, experimental measurements of apparent Young's moduli agree well with predictions of the theoretical Gibson-Ashby model. Thus, the anisotropic mechanical properties of a lattice can be tuned by the unit cell size, the strut diameter, and scaling factors. This approach will be valuable in designing tissue-mimicking hydrogel lattice-based composite materials for elastography phantoms and tissue engineered scaffolds.
期刊介绍:
The Journal of the Mechanical Behavior of Biomedical Materials is concerned with the mechanical deformation, damage and failure under applied forces, of biological material (at the tissue, cellular and molecular levels) and of biomaterials, i.e. those materials which are designed to mimic or replace biological materials.
The primary focus of the journal is the synthesis of materials science, biology, and medical and dental science. Reports of fundamental scientific investigations are welcome, as are articles concerned with the practical application of materials in medical devices. Both experimental and theoretical work is of interest; theoretical papers will normally include comparison of predictions with experimental data, though we recognize that this may not always be appropriate. The journal also publishes technical notes concerned with emerging experimental or theoretical techniques, letters to the editor and, by invitation, review articles and papers describing existing techniques for the benefit of an interdisciplinary readership.