Degree of conversion and residual monomer elution of 3D-printed, milled and self-cured resin-based composite materials for temporary dental crowns and bridges
Eva Berghaus, Thorsten Klocke, Reinhard Maletz, Svea Petersen
{"title":"Degree of conversion and residual monomer elution of 3D-printed, milled and self-cured resin-based composite materials for temporary dental crowns and bridges","authors":"Eva Berghaus, Thorsten Klocke, Reinhard Maletz, Svea Petersen","doi":"10.1007/s10856-023-06729-z","DOIUrl":null,"url":null,"abstract":"<div><p>The aim of this work was to investigate the elution of residual monomers as a function of the manufacturing process, which are CAD/CAM manufacturing, self-curing and 3D printing. The experimental materials used consisted of the base monomers TEGDMA, Bis-GMA and Bis-EMA and 50 wt.% fillers. Additionally, a 3D printing resin without fillers was tested. The elution of the base monomers into the different media (water, ethanol and ethanol/water (75/25 vol. %)) at 37 °C over a period of up to 120 d as well as the degree of conversion (DC) by FTIR were investigated. No monomer elution could be detected in water. Most residual monomers in both other media were released from the self-curing material whereas the 3D printing composite released relatively little. The CAD/CAM blanks released hardly any quantitatively detectable amounts of monomers. Relative to the base composition, TEGDMA eluted less than Bis-GMA and Bis-EMA. DC did not correlate with residual monomer release; thus, leaching was determined not only by the amount of residual monomers present but by further factors as possibly network density and structure. The CAD/CAM blanks and the 3D printing composite showed similar high DC but lower residual monomer release from the CAD/CAM blank, likewise the self-curing composite and the 3D printing resin exhibited similar DC but different monomer elution. In terms of residual monomer elution and DC, the 3D printing composite seems promising as a new material class for the use as temporary dental crowns and bridges.</p><h3>Graphical Abstract</h3>\n <figure><div><div><div><picture><source><img></source></picture></div></div></div></figure>\n </div>","PeriodicalId":647,"journal":{"name":"Journal of Materials Science: Materials in Medicine","volume":null,"pages":null},"PeriodicalIF":4.2000,"publicationDate":"2023-05-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"https://link.springer.com/content/pdf/10.1007/s10856-023-06729-z.pdf","citationCount":"1","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Journal of Materials Science: Materials in Medicine","FirstCategoryId":"5","ListUrlMain":"https://link.springer.com/article/10.1007/s10856-023-06729-z","RegionNum":3,"RegionCategory":"医学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q2","JCRName":"ENGINEERING, BIOMEDICAL","Score":null,"Total":0}
引用次数: 1
Abstract
The aim of this work was to investigate the elution of residual monomers as a function of the manufacturing process, which are CAD/CAM manufacturing, self-curing and 3D printing. The experimental materials used consisted of the base monomers TEGDMA, Bis-GMA and Bis-EMA and 50 wt.% fillers. Additionally, a 3D printing resin without fillers was tested. The elution of the base monomers into the different media (water, ethanol and ethanol/water (75/25 vol. %)) at 37 °C over a period of up to 120 d as well as the degree of conversion (DC) by FTIR were investigated. No monomer elution could be detected in water. Most residual monomers in both other media were released from the self-curing material whereas the 3D printing composite released relatively little. The CAD/CAM blanks released hardly any quantitatively detectable amounts of monomers. Relative to the base composition, TEGDMA eluted less than Bis-GMA and Bis-EMA. DC did not correlate with residual monomer release; thus, leaching was determined not only by the amount of residual monomers present but by further factors as possibly network density and structure. The CAD/CAM blanks and the 3D printing composite showed similar high DC but lower residual monomer release from the CAD/CAM blank, likewise the self-curing composite and the 3D printing resin exhibited similar DC but different monomer elution. In terms of residual monomer elution and DC, the 3D printing composite seems promising as a new material class for the use as temporary dental crowns and bridges.
期刊介绍：
The Journal of Materials Science: Materials in Medicine publishes refereed papers providing significant progress in the application of biomaterials and tissue engineering constructs as medical or dental implants, prostheses and devices. Coverage spans a wide range of topics from basic science to clinical applications, around the theme of materials in medicine and dentistry. The central element is the development of synthetic and natural materials used in orthopaedic, maxillofacial, cardiovascular, neurological, ophthalmic and dental applications. Special biomedical topics include biomaterial synthesis and characterisation, biocompatibility studies, nanomedicine, tissue engineering constructs and cell substrates, regenerative medicine, computer modelling and other advanced experimental methodologies.
求助内容：
应助结果提醒方式：
京公网安备 11010802042870号
