{"title":"利用硅基开关设备提高功率因数,改变负载参数","authors":"Popuri Rajani Kumari, Kasula Rajasri, Tadi Diwakara Subba Reddy, Ambarapu Sudhakar, Bodapati Venkata Rajanna","doi":"10.11591/ijape.v12.i4.pp367-372","DOIUrl":null,"url":null,"abstract":"Systems power factor provides information on how effectively it uses the electrical power being provided to hold out real work. Losses rise as a results of poor power factor, and therefore the utility is penalized. In general, inductive loads, which are reactive in nature, make up AC loads. As a result, loads require and consume reactive power from the supply source which leads to excessive voltage drop in the line if they draw a lot of lagging current from the source, which could potentially result in the line's voltage collapsing if the drop is too high. When inductors cause a phase difference between voltage and current, the information is sent to the micro-controller, where the program takes control and activates the right number of opto-isolators interfaced to the triac silicon-based semiconductor device at its output to bring shunt capacitors into the load circuit to improve power factor to the desired range Semiconductors such as silicon or germanium are generally used for making triac. The most commonly used is silicon, due to its high abundance and the fact that it can operate at a higher temperature than germanium.","PeriodicalId":340072,"journal":{"name":"International Journal of Applied Power Engineering (IJAPE)","volume":" 1","pages":""},"PeriodicalIF":0.0000,"publicationDate":"2023-12-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Power factor improvement using silicon based switching devices for changing load parameters\",\"authors\":\"Popuri Rajani Kumari, Kasula Rajasri, Tadi Diwakara Subba Reddy, Ambarapu Sudhakar, Bodapati Venkata Rajanna\",\"doi\":\"10.11591/ijape.v12.i4.pp367-372\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"Systems power factor provides information on how effectively it uses the electrical power being provided to hold out real work. Losses rise as a results of poor power factor, and therefore the utility is penalized. In general, inductive loads, which are reactive in nature, make up AC loads. As a result, loads require and consume reactive power from the supply source which leads to excessive voltage drop in the line if they draw a lot of lagging current from the source, which could potentially result in the line's voltage collapsing if the drop is too high. When inductors cause a phase difference between voltage and current, the information is sent to the micro-controller, where the program takes control and activates the right number of opto-isolators interfaced to the triac silicon-based semiconductor device at its output to bring shunt capacitors into the load circuit to improve power factor to the desired range Semiconductors such as silicon or germanium are generally used for making triac. The most commonly used is silicon, due to its high abundance and the fact that it can operate at a higher temperature than germanium.\",\"PeriodicalId\":340072,\"journal\":{\"name\":\"International Journal of Applied Power Engineering (IJAPE)\",\"volume\":\" 1\",\"pages\":\"\"},\"PeriodicalIF\":0.0000,\"publicationDate\":\"2023-12-01\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"International Journal of Applied Power Engineering (IJAPE)\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.11591/ijape.v12.i4.pp367-372\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"\",\"JCRName\":\"\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"International Journal of Applied Power Engineering (IJAPE)","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.11591/ijape.v12.i4.pp367-372","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
Power factor improvement using silicon based switching devices for changing load parameters
Systems power factor provides information on how effectively it uses the electrical power being provided to hold out real work. Losses rise as a results of poor power factor, and therefore the utility is penalized. In general, inductive loads, which are reactive in nature, make up AC loads. As a result, loads require and consume reactive power from the supply source which leads to excessive voltage drop in the line if they draw a lot of lagging current from the source, which could potentially result in the line's voltage collapsing if the drop is too high. When inductors cause a phase difference between voltage and current, the information is sent to the micro-controller, where the program takes control and activates the right number of opto-isolators interfaced to the triac silicon-based semiconductor device at its output to bring shunt capacitors into the load circuit to improve power factor to the desired range Semiconductors such as silicon or germanium are generally used for making triac. The most commonly used is silicon, due to its high abundance and the fact that it can operate at a higher temperature than germanium.