扫描方向双光斑光束设置光纤激光切割钢板

IF 1.7 4区 工程技术 Q3 MATERIALS SCIENCE, MULTIDISCIPLINARY
Yasuhiro Okamoto, Kota Morimoto, Naoki Kai, Akira Okada, Hiroaki Ishiguro, Ryohei Ito, Hiroshi Okawa
{"title":"扫描方向双光斑光束设置光纤激光切割钢板","authors":"Yasuhiro Okamoto, Kota Morimoto, Naoki Kai, Akira Okada, Hiroaki Ishiguro, Ryohei Ito, Hiroshi Okawa","doi":"10.2351/7.0001097","DOIUrl":null,"url":null,"abstract":"This study investigated the effects of laser beam intensity distribution on the reduction of dross height in fiber laser cutting of a steel plate with 3.2 mm thickness. A twin-spot beam was produced by splitting a single Gaussian beam into two beams using a special axicon lens, and these beams were set in the scanning direction for cutting experiments. The power ratio of two beams (R:F = Rear power:Front power) was varied to discuss the intensity balance for the effective reduction of dross. After cutting experiments, ray tracing analysis was conducted using an optical analysis to calculate the absorbed power density distributions in the kerf. A smaller dross height of 18 μm can be achieved at a power ratio of R:F = 8:2, and its value is lower than that by a single Gaussian beam. At a power ratio of R:F = 8:2, the front beam of lower power is irradiated at the upper part of the workpiece, and the rear beam of higher power is absorbed at the lower part of the workpiece. Thus, effective heat input to the lower part of the workpiece can contribute to a reduction of the dross height. Variation of power ratio in the rear and the front beams is effective in controlling the cutting front shape, and the uniformity of absorbed power in the thickness direction can be improved by setting the rear beam of about four times higher power to the front beam of lower power to obtain a smaller dross height in the case of a 3.2 mm steel plate.","PeriodicalId":50168,"journal":{"name":"Journal of Laser Applications","volume":null,"pages":null},"PeriodicalIF":1.7000,"publicationDate":"2023-10-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Fiber laser cutting of steel plate by twin spot beam setting in scanning direction\",\"authors\":\"Yasuhiro Okamoto, Kota Morimoto, Naoki Kai, Akira Okada, Hiroaki Ishiguro, Ryohei Ito, Hiroshi Okawa\",\"doi\":\"10.2351/7.0001097\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"This study investigated the effects of laser beam intensity distribution on the reduction of dross height in fiber laser cutting of a steel plate with 3.2 mm thickness. A twin-spot beam was produced by splitting a single Gaussian beam into two beams using a special axicon lens, and these beams were set in the scanning direction for cutting experiments. The power ratio of two beams (R:F = Rear power:Front power) was varied to discuss the intensity balance for the effective reduction of dross. After cutting experiments, ray tracing analysis was conducted using an optical analysis to calculate the absorbed power density distributions in the kerf. A smaller dross height of 18 μm can be achieved at a power ratio of R:F = 8:2, and its value is lower than that by a single Gaussian beam. At a power ratio of R:F = 8:2, the front beam of lower power is irradiated at the upper part of the workpiece, and the rear beam of higher power is absorbed at the lower part of the workpiece. Thus, effective heat input to the lower part of the workpiece can contribute to a reduction of the dross height. Variation of power ratio in the rear and the front beams is effective in controlling the cutting front shape, and the uniformity of absorbed power in the thickness direction can be improved by setting the rear beam of about four times higher power to the front beam of lower power to obtain a smaller dross height in the case of a 3.2 mm steel plate.\",\"PeriodicalId\":50168,\"journal\":{\"name\":\"Journal of Laser Applications\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":1.7000,\"publicationDate\":\"2023-10-18\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Journal of Laser Applications\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.2351/7.0001097\",\"RegionNum\":4,\"RegionCategory\":\"工程技术\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q3\",\"JCRName\":\"MATERIALS SCIENCE, MULTIDISCIPLINARY\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Journal of Laser Applications","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.2351/7.0001097","RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q3","JCRName":"MATERIALS SCIENCE, MULTIDISCIPLINARY","Score":null,"Total":0}
引用次数: 0

摘要

研究了光纤激光切割厚度为3.2 mm的钢板时,激光束强度分布对切屑高度降低的影响。利用一种特殊的轴突透镜将一束高斯光束分成两束,产生双点光束,并将这两束光束设置在扫描方向上进行切割实验。通过改变两束光束的功率比(R:F =后功率:前功率),探讨了有效减渣的强度平衡。切割实验结束后,利用光学分析进行光线追迹分析,计算切口内吸收功率密度分布。当功率比为R:F = 8:2时,可获得更小的杂散高度,仅为18 μm,且其值低于单高斯光束。当功率比为R:F = 8:2时,较低功率的前光束照射到工件的上部,较高功率的后光束照射到工件的下部。因此,有效的热量输入到工件的下部可以有助于减少渣滓高度。改变前后梁的功率比可以有效地控制切割前形状,在3.2 mm钢板的情况下,将高功率的后梁与低功率的前梁分别设置4倍左右,可以提高吸收功率在厚度方向上的均匀性,从而获得较小的截渣高度。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
Fiber laser cutting of steel plate by twin spot beam setting in scanning direction
This study investigated the effects of laser beam intensity distribution on the reduction of dross height in fiber laser cutting of a steel plate with 3.2 mm thickness. A twin-spot beam was produced by splitting a single Gaussian beam into two beams using a special axicon lens, and these beams were set in the scanning direction for cutting experiments. The power ratio of two beams (R:F = Rear power:Front power) was varied to discuss the intensity balance for the effective reduction of dross. After cutting experiments, ray tracing analysis was conducted using an optical analysis to calculate the absorbed power density distributions in the kerf. A smaller dross height of 18 μm can be achieved at a power ratio of R:F = 8:2, and its value is lower than that by a single Gaussian beam. At a power ratio of R:F = 8:2, the front beam of lower power is irradiated at the upper part of the workpiece, and the rear beam of higher power is absorbed at the lower part of the workpiece. Thus, effective heat input to the lower part of the workpiece can contribute to a reduction of the dross height. Variation of power ratio in the rear and the front beams is effective in controlling the cutting front shape, and the uniformity of absorbed power in the thickness direction can be improved by setting the rear beam of about four times higher power to the front beam of lower power to obtain a smaller dross height in the case of a 3.2 mm steel plate.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
CiteScore
3.60
自引率
9.50%
发文量
125
审稿时长
>12 weeks
期刊介绍: The Journal of Laser Applications (JLA) is the scientific platform of the Laser Institute of America (LIA) and is published in cooperation with AIP Publishing. The high-quality articles cover a broad range from fundamental and applied research and development to industrial applications. Therefore, JLA is a reflection of the state-of-R&D in photonic production, sensing and measurement as well as Laser safety. The following international and well known first-class scientists serve as allocated Editors in 9 new categories: High Precision Materials Processing with Ultrafast Lasers Laser Additive Manufacturing High Power Materials Processing with High Brightness Lasers Emerging Applications of Laser Technologies in High-performance/Multi-function Materials and Structures Surface Modification Lasers in Nanomanufacturing / Nanophotonics & Thin Film Technology Spectroscopy / Imaging / Diagnostics / Measurements Laser Systems and Markets Medical Applications & Safety Thermal Transportation Nanomaterials and Nanoprocessing Laser applications in Microelectronics.
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
确定
请完成安全验证×
copy
已复制链接
快去分享给好友吧!
我知道了
右上角分享
点击右上角分享
0
联系我们:info@booksci.cn Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。 Copyright © 2023 布克学术 All rights reserved.
京ICP备2023020795号-1
ghs 京公网安备 11010802042870号
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术官方微信