304L不锈钢摩擦堆焊接触半径:主轴转速和杆径的影响

IF 2.4 3区 工程技术 Q3 ENGINEERING, MANUFACTURING
Hemant Agiwal, Hwasung Yeom, Kumar Sridharan, Shiva Rudraraju, Frank E. Pfefferkorn
{"title":"304L不锈钢摩擦堆焊接触半径:主轴转速和杆径的影响","authors":"Hemant Agiwal, Hwasung Yeom, Kumar Sridharan, Shiva Rudraraju, Frank E. Pfefferkorn","doi":"10.1115/1.4063653","DOIUrl":null,"url":null,"abstract":"Abstract The ‘radius of contact’ or the ‘real-rotational contact plane’, has been increasingly mentioned terminology in friction surfacing. However, the fundamental understanding of the flow dynamics behind this phenomenon is still very limited. The goal of this study was to understand the influence of spindle speed and consumable rod diameter on the flow dynamics and radius of contact during friction surfacing of 304L stainless steel over a substrate of the same material. Friction surfacing was performed using consumable rods with diameters of 4.76 mm, 9.52 mm, and 12.7 mm while using spindle speeds from 1,500 RPM to 20,000 RPM. The impact of spindle speed on deposition morphology, including the radius of contact, was studied. The radius of contact was calculated empirically and was found to be inversely proportional to the tangential velocity of the rod. The coupling between flow stresses and localized forces is hypothesized to be the key factor behind the variation of the radius of contact with processing conditions.","PeriodicalId":16299,"journal":{"name":"Journal of Manufacturing Science and Engineering-transactions of The Asme","volume":null,"pages":null},"PeriodicalIF":2.4000,"publicationDate":"2023-10-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Radius of Contact During Friction Surfacing of Stainless Steel 304L: Effect of Spindle Speed and Rod Diameter\",\"authors\":\"Hemant Agiwal, Hwasung Yeom, Kumar Sridharan, Shiva Rudraraju, Frank E. Pfefferkorn\",\"doi\":\"10.1115/1.4063653\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"Abstract The ‘radius of contact’ or the ‘real-rotational contact plane’, has been increasingly mentioned terminology in friction surfacing. However, the fundamental understanding of the flow dynamics behind this phenomenon is still very limited. The goal of this study was to understand the influence of spindle speed and consumable rod diameter on the flow dynamics and radius of contact during friction surfacing of 304L stainless steel over a substrate of the same material. Friction surfacing was performed using consumable rods with diameters of 4.76 mm, 9.52 mm, and 12.7 mm while using spindle speeds from 1,500 RPM to 20,000 RPM. The impact of spindle speed on deposition morphology, including the radius of contact, was studied. The radius of contact was calculated empirically and was found to be inversely proportional to the tangential velocity of the rod. The coupling between flow stresses and localized forces is hypothesized to be the key factor behind the variation of the radius of contact with processing conditions.\",\"PeriodicalId\":16299,\"journal\":{\"name\":\"Journal of Manufacturing Science and Engineering-transactions of The Asme\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":2.4000,\"publicationDate\":\"2023-10-04\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Journal of Manufacturing Science and Engineering-transactions of The Asme\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.1115/1.4063653\",\"RegionNum\":3,\"RegionCategory\":\"工程技术\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q3\",\"JCRName\":\"ENGINEERING, MANUFACTURING\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Journal of Manufacturing Science and Engineering-transactions of The Asme","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.1115/1.4063653","RegionNum":3,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q3","JCRName":"ENGINEERING, MANUFACTURING","Score":null,"Total":0}
引用次数: 0

摘要

“接触半径”或“实旋转接触面”是摩擦表面加工中越来越多地被提及的术语。然而,对这种现象背后的流动动力学的基本理解仍然非常有限。本研究的目的是了解主轴转速和耗材杆直径对304L不锈钢摩擦表面在相同材料基体上的流动动力学和接触半径的影响。采用直径为4.76 mm、9.52 mm和12.7 mm的耗材进行摩擦堆焊,主轴转速为1,500 RPM至20,000 RPM。研究了主轴转速对接触半径等沉积形貌的影响。根据经验计算接触半径,发现接触半径与杆的切向速度成反比。假设流动应力和局部力之间的耦合是接触半径随加工条件变化的关键因素。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
Radius of Contact During Friction Surfacing of Stainless Steel 304L: Effect of Spindle Speed and Rod Diameter
Abstract The ‘radius of contact’ or the ‘real-rotational contact plane’, has been increasingly mentioned terminology in friction surfacing. However, the fundamental understanding of the flow dynamics behind this phenomenon is still very limited. The goal of this study was to understand the influence of spindle speed and consumable rod diameter on the flow dynamics and radius of contact during friction surfacing of 304L stainless steel over a substrate of the same material. Friction surfacing was performed using consumable rods with diameters of 4.76 mm, 9.52 mm, and 12.7 mm while using spindle speeds from 1,500 RPM to 20,000 RPM. The impact of spindle speed on deposition morphology, including the radius of contact, was studied. The radius of contact was calculated empirically and was found to be inversely proportional to the tangential velocity of the rod. The coupling between flow stresses and localized forces is hypothesized to be the key factor behind the variation of the radius of contact with processing conditions.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
CiteScore
6.80
自引率
20.00%
发文量
126
审稿时长
12 months
期刊介绍: Areas of interest including, but not limited to: Additive manufacturing; Advanced materials and processing; Assembly; Biomedical manufacturing; Bulk deformation processes (e.g., extrusion, forging, wire drawing, etc.); CAD/CAM/CAE; Computer-integrated manufacturing; Control and automation; Cyber-physical systems in manufacturing; Data science-enhanced manufacturing; Design for manufacturing; Electrical and electrochemical machining; Grinding and abrasive processes; Injection molding and other polymer fabrication processes; Inspection and quality control; Laser processes; Machine tool dynamics; Machining processes; Materials handling; Metrology; Micro- and nano-machining and processing; Modeling and simulation; Nontraditional manufacturing processes; Plant engineering and maintenance; Powder processing; Precision and ultra-precision machining; Process engineering; Process planning; Production systems optimization; Rapid prototyping and solid freeform fabrication; Robotics and flexible tooling; Sensing, monitoring, and diagnostics; Sheet and tube metal forming; Sustainable manufacturing; Tribology in manufacturing; Welding and joining
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
确定
请完成安全验证×
copy
已复制链接
快去分享给好友吧!
我知道了
右上角分享
点击右上角分享
0
联系我们:info@booksci.cn Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。 Copyright © 2023 布克学术 All rights reserved.
京ICP备2023020795号-1
ghs 京公网安备 11010802042870号
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术官方微信