各向同性和各向异性基板上带通滤波器的WCIP方法分析

2015 SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC) Pub Date : 2015-11-01 DOI:10.1109/IMOC.2015.7369218

V. P. S. Neto, Jurgen K. A. Nogueira, A. D’assunção

{"title":"各向同性和各向异性基板上带通滤波器的WCIP方法分析","authors":"V. P. S. Neto, Jurgen K. A. Nogueira, A. D’assunção","doi":"10.1109/IMOC.2015.7369218","DOIUrl":null,"url":null,"abstract":"This work presents the frequency response analysis of a planar band pass filter using the WCIP method. The filter geometry is composed of a rectangular microstrip patch with a perforated complementary split ring resonator (CSRR). The investigation of the filter properties is done considering the perforated patch geometry printed on isotropic and anisotropic substrates. Simulations results are determined by WCIP method and HFSS software, for comparison purpose, for the filter resonant frequency, bandwidth, return loss, and insertion loss. A prototype of the proposed band pass filter printed on isotropic substrate was fabricated and measured. Simulation (WCIP and HFSS) and measurement results are in good agreement.","PeriodicalId":431462,"journal":{"name":"2015 SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC)","volume":"6 1","pages":"0"},"PeriodicalIF":0.0000,"publicationDate":"2015-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"2","resultStr":"{\"title\":\"Analysis of band pass filter printed on isotropic and anisotropic substrates by the WCIP method\",\"authors\":\"V. P. S. Neto, Jurgen K. A. Nogueira, A. D’assunção\",\"doi\":\"10.1109/IMOC.2015.7369218\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"This work presents the frequency response analysis of a planar band pass filter using the WCIP method. The filter geometry is composed of a rectangular microstrip patch with a perforated complementary split ring resonator (CSRR). The investigation of the filter properties is done considering the perforated patch geometry printed on isotropic and anisotropic substrates. Simulations results are determined by WCIP method and HFSS software, for comparison purpose, for the filter resonant frequency, bandwidth, return loss, and insertion loss. A prototype of the proposed band pass filter printed on isotropic substrate was fabricated and measured. Simulation (WCIP and HFSS) and measurement results are in good agreement.\",\"PeriodicalId\":431462,\"journal\":{\"name\":\"2015 SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC)\",\"volume\":\"6 1\",\"pages\":\"0\"},\"PeriodicalIF\":0.0000,\"publicationDate\":\"2015-11-01\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"2\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"2015 SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC)\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.1109/IMOC.2015.7369218\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"\",\"JCRName\":\"\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"2015 SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC)","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.1109/IMOC.2015.7369218","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}

引用次数: 2

摘要

本文采用WCIP方法对平面带通滤波器的频响进行了分析。该滤波器几何形状由矩形微带贴片和穿孔互补分裂环谐振器(CSRR)组成。考虑了各向同性和各向异性基板上印刷的穿孔贴片几何形状，对滤光片的性能进行了研究。利用WCIP方法和HFSS软件确定了滤波器谐振频率、带宽、回波损耗和插入损耗的仿真结果，并进行了比较。在各向同性基板上制作并测量了所提出的带通滤波器的原型。仿真(WCIP和HFSS)与实测结果吻合较好。

本文章由计算机程序翻译，如有差异，请以英文原文为准。

查看原文本刊更多论文

Analysis of band pass filter printed on isotropic and anisotropic substrates by the WCIP method

This work presents the frequency response analysis of a planar band pass filter using the WCIP method. The filter geometry is composed of a rectangular microstrip patch with a perforated complementary split ring resonator (CSRR). The investigation of the filter properties is done considering the perforated patch geometry printed on isotropic and anisotropic substrates. Simulations results are determined by WCIP method and HFSS software, for comparison purpose, for the filter resonant frequency, bandwidth, return loss, and insertion loss. A prototype of the proposed band pass filter printed on isotropic substrate was fabricated and measured. Simulation (WCIP and HFSS) and measurement results are in good agreement.

求助全文

通过发布文献求助，成功后即可免费获取论文全文。去求助

来源期刊

2015 SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC)

自引率

0.00%

发文量