{"title":"工艺空气条件下MIL100 (Fe)涂层除湿转子除湿性能评价","authors":"J. Y. Chung, M. Park, Sewon Lee, Yongchan Kim","doi":"10.11159/htff22.146","DOIUrl":null,"url":null,"abstract":"Extended Abstract Adsorbents are the main design factor in the desiccant rotor of a solid dehumidification system because they are directly related to the dehumidification and energy performance [1,2]. Silica gel and zeolite have been widely used in conventional desiccant rotors owing to their wide range of temperature and humidity conditions. However, they have a limitation to dramatically enhance the dehumidification and energy performance of a desiccant rotor owing to its high regeneration temperature and low water adsorption capacity [3]. In this regard, MIL-100 (Fe) has attracted attention to overcome this challenge because it has a low regeneration temperature and high-water adsorption capacity [4,5]. However, studies on the desiccant rotor coated with MIL-100 (Fe) have been very limited. Therefore, the moisture removal capacity (MRC) and dehumidification coefficient of performance (DCOP) of a desiccant rotor coated with MIL-100 (Fe) must be investigated to figure out the dehumidification and energy performance. In this study, the MRC and DCOP of the desiccant rotor coated with MIL-100 (Fe) were investigated through experiments under various process air conditions. The experimental setup was constructed in the environmental chamber based on the NREL desiccant wheel test guide [6] and ASHRAE standard 174 [7]. The desiccant","PeriodicalId":385356,"journal":{"name":"Proceedings of the 8th World Congress on Mechanical, Chemical, and Material Engineering","volume":null,"pages":null},"PeriodicalIF":0.0000,"publicationDate":"2022-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Dehumidification Performance Evaluation of a Desiccant Rotor Coated With MIL100 (Fe) Under Process Air Conditions\",\"authors\":\"J. Y. Chung, M. Park, Sewon Lee, Yongchan Kim\",\"doi\":\"10.11159/htff22.146\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"Extended Abstract Adsorbents are the main design factor in the desiccant rotor of a solid dehumidification system because they are directly related to the dehumidification and energy performance [1,2]. Silica gel and zeolite have been widely used in conventional desiccant rotors owing to their wide range of temperature and humidity conditions. However, they have a limitation to dramatically enhance the dehumidification and energy performance of a desiccant rotor owing to its high regeneration temperature and low water adsorption capacity [3]. In this regard, MIL-100 (Fe) has attracted attention to overcome this challenge because it has a low regeneration temperature and high-water adsorption capacity [4,5]. However, studies on the desiccant rotor coated with MIL-100 (Fe) have been very limited. Therefore, the moisture removal capacity (MRC) and dehumidification coefficient of performance (DCOP) of a desiccant rotor coated with MIL-100 (Fe) must be investigated to figure out the dehumidification and energy performance. In this study, the MRC and DCOP of the desiccant rotor coated with MIL-100 (Fe) were investigated through experiments under various process air conditions. The experimental setup was constructed in the environmental chamber based on the NREL desiccant wheel test guide [6] and ASHRAE standard 174 [7]. The desiccant\",\"PeriodicalId\":385356,\"journal\":{\"name\":\"Proceedings of the 8th World Congress on Mechanical, Chemical, and Material Engineering\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":0.0000,\"publicationDate\":\"2022-08-01\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Proceedings of the 8th World Congress on Mechanical, Chemical, and Material Engineering\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.11159/htff22.146\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"\",\"JCRName\":\"\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Proceedings of the 8th World Congress on Mechanical, Chemical, and Material Engineering","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.11159/htff22.146","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
Dehumidification Performance Evaluation of a Desiccant Rotor Coated With MIL100 (Fe) Under Process Air Conditions
Extended Abstract Adsorbents are the main design factor in the desiccant rotor of a solid dehumidification system because they are directly related to the dehumidification and energy performance [1,2]. Silica gel and zeolite have been widely used in conventional desiccant rotors owing to their wide range of temperature and humidity conditions. However, they have a limitation to dramatically enhance the dehumidification and energy performance of a desiccant rotor owing to its high regeneration temperature and low water adsorption capacity [3]. In this regard, MIL-100 (Fe) has attracted attention to overcome this challenge because it has a low regeneration temperature and high-water adsorption capacity [4,5]. However, studies on the desiccant rotor coated with MIL-100 (Fe) have been very limited. Therefore, the moisture removal capacity (MRC) and dehumidification coefficient of performance (DCOP) of a desiccant rotor coated with MIL-100 (Fe) must be investigated to figure out the dehumidification and energy performance. In this study, the MRC and DCOP of the desiccant rotor coated with MIL-100 (Fe) were investigated through experiments under various process air conditions. The experimental setup was constructed in the environmental chamber based on the NREL desiccant wheel test guide [6] and ASHRAE standard 174 [7]. The desiccant