电动汽车的微处理器控制

F. Colliver, W. D. Wesson, L. Grigsby
{"title":"电动汽车的微处理器控制","authors":"F. Colliver, W. D. Wesson, L. Grigsby","doi":"10.1109/VTC.1978.1622514","DOIUrl":null,"url":null,"abstract":"This paper will investigate the use of a micro-processor to control the operation of a d-c series motor that is used to drive a battery powered van. The microprocessor will accomplish this control by sampling the speed of the vehicle and comparing this speed to the desired speed, which is set by the operator, and then vary the duty cycle of the SCR chopper based on the computed speed error to maintain the vehicle at the desired speed. It should be pointed out that the reference speed signal is not to be preset such that the microprocessor must maintain only one speed, but rather the input speed reference is capable of being varied continuously from zero to maximum rated speed and the microprocessor is to track this varying reference and control the vehicle to this speed.","PeriodicalId":264799,"journal":{"name":"28th IEEE Vehicular Technology Conference","volume":"19 1","pages":"0"},"PeriodicalIF":0.0000,"publicationDate":"1978-03-22","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"2","resultStr":"{\"title\":\"Microprocessor control of an electric vehicle\",\"authors\":\"F. Colliver, W. D. Wesson, L. Grigsby\",\"doi\":\"10.1109/VTC.1978.1622514\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"This paper will investigate the use of a micro-processor to control the operation of a d-c series motor that is used to drive a battery powered van. The microprocessor will accomplish this control by sampling the speed of the vehicle and comparing this speed to the desired speed, which is set by the operator, and then vary the duty cycle of the SCR chopper based on the computed speed error to maintain the vehicle at the desired speed. It should be pointed out that the reference speed signal is not to be preset such that the microprocessor must maintain only one speed, but rather the input speed reference is capable of being varied continuously from zero to maximum rated speed and the microprocessor is to track this varying reference and control the vehicle to this speed.\",\"PeriodicalId\":264799,\"journal\":{\"name\":\"28th IEEE Vehicular Technology Conference\",\"volume\":\"19 1\",\"pages\":\"0\"},\"PeriodicalIF\":0.0000,\"publicationDate\":\"1978-03-22\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"2\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"28th IEEE Vehicular Technology Conference\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.1109/VTC.1978.1622514\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"\",\"JCRName\":\"\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"28th IEEE Vehicular Technology Conference","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.1109/VTC.1978.1622514","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
引用次数: 2

摘要

本文将研究使用微处理器来控制用于驱动电池供电面包车的直流串联电动机的运行。微处理器将通过采样车辆的速度并将此速度与由操作员设置的所需速度进行比较来完成此控制,然后根据计算的速度误差改变可控硅斩波器的占空比,以保持车辆在所需速度。应该指出的是,参考速度信号不是预先设定的,这样微处理器必须只保持一个速度,而是输入的参考速度能够从零到最大额定速度连续变化,微处理器要跟踪这个变化的参考并控制车辆达到这个速度。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
Microprocessor control of an electric vehicle
This paper will investigate the use of a micro-processor to control the operation of a d-c series motor that is used to drive a battery powered van. The microprocessor will accomplish this control by sampling the speed of the vehicle and comparing this speed to the desired speed, which is set by the operator, and then vary the duty cycle of the SCR chopper based on the computed speed error to maintain the vehicle at the desired speed. It should be pointed out that the reference speed signal is not to be preset such that the microprocessor must maintain only one speed, but rather the input speed reference is capable of being varied continuously from zero to maximum rated speed and the microprocessor is to track this varying reference and control the vehicle to this speed.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
CiteScore
2.20
自引率
0.00%
发文量
0
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
确定
请完成安全验证×
copy
已复制链接
快去分享给好友吧!
我知道了
右上角分享
点击右上角分享
0
联系我们:info@booksci.cn Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。 Copyright © 2023 布克学术 All rights reserved.
京ICP备2023020795号-1
ghs 京公网安备 11010802042870号
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术官方微信