{"title":"Seismic fragility analysis of high‐strength concrete frame structures reinforced with high‐strength steel bars","authors":"Juan Liu, Jianwei Zhang, Zuozhou Zhao","doi":"10.1002/tal.2103","DOIUrl":null,"url":null,"abstract":"SummaryTo investigate the influence of using high‐strength steel bars in columns on the seismic resistance capacity and seismic resilience of frame structures, seismic fragility evaluation of three 8‐story reinforced concrete (RC) frame structures was conducted based on the incremental dynamic analysis (IDA) using 11 ground motion records. The main parameter is the longitudinal reinforcement configuration in the frame columns, where the first structure is reinforced with HRB 600 grade steel bars in the columns, the second structure is replaced with equal area ultra‐high‐strength (UHS) steel bars (i.e., with a yield strength of approximately 1425 MPa), and the third structure is replaced with equal strength UHS steel bars. A numerical model of the RC frame structure was developed and then validated using previous experimental results. The exceeding probabilities at various performance limit states were calculated based on two typical engineering demand parameters (EDPs) of maximum interstory drift and residual interstory drift. The results showed that using UHS longitudinal steel bars instead of HRB 600 grade steel bars in frame columns could reduce the energy dissipation capacity of the structure, inevitably leading to an increase in the maximum interstory response of the frame. However, much lower exceedance probability was observed in the UHS‐enhanced frame under the repair available limit state based on the residual interstory drift, indicating that the UHS‐enhanced RC frame had higher seismic resilience. In addition, compared to equal area substitution, equal strength substitution is a more ideal design method that can use fewer UHS steel bars to achieve comparable reparability and a smaller increase in maximum interstory drift.","PeriodicalId":501238,"journal":{"name":"The Structural Design of Tall and Special Buildings","volume":"28 1","pages":""},"PeriodicalIF":0.0000,"publicationDate":"2024-03-02","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"The Structural Design of Tall and Special Buildings","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.1002/tal.2103","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
引用次数: 0
Abstract
SummaryTo investigate the influence of using high‐strength steel bars in columns on the seismic resistance capacity and seismic resilience of frame structures, seismic fragility evaluation of three 8‐story reinforced concrete (RC) frame structures was conducted based on the incremental dynamic analysis (IDA) using 11 ground motion records. The main parameter is the longitudinal reinforcement configuration in the frame columns, where the first structure is reinforced with HRB 600 grade steel bars in the columns, the second structure is replaced with equal area ultra‐high‐strength (UHS) steel bars (i.e., with a yield strength of approximately 1425 MPa), and the third structure is replaced with equal strength UHS steel bars. A numerical model of the RC frame structure was developed and then validated using previous experimental results. The exceeding probabilities at various performance limit states were calculated based on two typical engineering demand parameters (EDPs) of maximum interstory drift and residual interstory drift. The results showed that using UHS longitudinal steel bars instead of HRB 600 grade steel bars in frame columns could reduce the energy dissipation capacity of the structure, inevitably leading to an increase in the maximum interstory response of the frame. However, much lower exceedance probability was observed in the UHS‐enhanced frame under the repair available limit state based on the residual interstory drift, indicating that the UHS‐enhanced RC frame had higher seismic resilience. In addition, compared to equal area substitution, equal strength substitution is a more ideal design method that can use fewer UHS steel bars to achieve comparable reparability and a smaller increase in maximum interstory drift.