New Insights From Conceptual Design of an Additive Manufactured 300 W Micro Gas Turbine Towards UAV Applications

Lukas Badum, B. Leizeronok, B. Cukurel
{"title":"New Insights From Conceptual Design of an Additive Manufactured 300 W Micro Gas Turbine Towards UAV Applications","authors":"Lukas Badum, B. Leizeronok, B. Cukurel","doi":"10.1115/GT2020-16218","DOIUrl":null,"url":null,"abstract":"\n Owing to the high energy density of hydrocarbon fuels, ultra-micro gas turbines with power outputs below 1 kW have clear potential as battery replacement in drones. However, previous works on gas turbines of this scale revealed severe challenges due to air bearing failures, heat transfer from turbine to compressor, rotordynamic instability and manufacturing limitations. To overcome these obstacles, a novel gas turbine architecture is proposed based on conventional roller bearing technology that operates at up to 500,000 RPM and an additively manufactured monolithic rotor in cantilevered configuration, equipped with internal cooling blades. The optimum turbomachinery design is elaborated using diabatic cycle calculation, coupled with turbomachinery meanline design code. This approach provides new insights on the interdependencies of heat transfer, component efficiency and system electric efficiency. Thereby, a reduced design pressure ratio of 2.5 with 1200 K turbine inlet temperature is identified as most suitable for 300 W electric power output. In following, a review of available additive manufacturing technologies yields material properties, surface roughness and design constraints for the monolithic rotor. Rotordynamic simulations are then conducted for four available materials using a simplified rotor model to identify valid permanent magnet dimensions that would avoid operation close to bending modes. To complete the baseline engine architecture, a novel radial inflow combustor concept is proposed based on porous inert media combustion. CFD simulations are conducted to quantify compressor efficiency and conjugate heat transfer analysis of the monolithic rotor is performed to assess the benefit of the internal cooling cavity and vanes for different rotor materials. It is demonstrated that the cavity flow absorbs large amount of heat flux from turbine to compressor, thus cooling the rotor structure and improving the diabatic cycle efficiency. Finally, the results of this conceptual study show that ultra-micro gas turbine with electric efficiency of up to 5% is feasible, while energy density is increased by factor of 3.6, compared to lithium-ion batteries.","PeriodicalId":211867,"journal":{"name":"Volume 8: Industrial and Cogeneration; Manufacturing Materials and Metallurgy; Marine; Microturbines, Turbochargers, and Small Turbomachines","volume":"9 1","pages":"0"},"PeriodicalIF":0.0000,"publicationDate":"2020-09-21","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"2","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Volume 8: Industrial and Cogeneration; Manufacturing Materials and Metallurgy; Marine; Microturbines, Turbochargers, and Small Turbomachines","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.1115/GT2020-16218","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
引用次数: 2

Abstract

Owing to the high energy density of hydrocarbon fuels, ultra-micro gas turbines with power outputs below 1 kW have clear potential as battery replacement in drones. However, previous works on gas turbines of this scale revealed severe challenges due to air bearing failures, heat transfer from turbine to compressor, rotordynamic instability and manufacturing limitations. To overcome these obstacles, a novel gas turbine architecture is proposed based on conventional roller bearing technology that operates at up to 500,000 RPM and an additively manufactured monolithic rotor in cantilevered configuration, equipped with internal cooling blades. The optimum turbomachinery design is elaborated using diabatic cycle calculation, coupled with turbomachinery meanline design code. This approach provides new insights on the interdependencies of heat transfer, component efficiency and system electric efficiency. Thereby, a reduced design pressure ratio of 2.5 with 1200 K turbine inlet temperature is identified as most suitable for 300 W electric power output. In following, a review of available additive manufacturing technologies yields material properties, surface roughness and design constraints for the monolithic rotor. Rotordynamic simulations are then conducted for four available materials using a simplified rotor model to identify valid permanent magnet dimensions that would avoid operation close to bending modes. To complete the baseline engine architecture, a novel radial inflow combustor concept is proposed based on porous inert media combustion. CFD simulations are conducted to quantify compressor efficiency and conjugate heat transfer analysis of the monolithic rotor is performed to assess the benefit of the internal cooling cavity and vanes for different rotor materials. It is demonstrated that the cavity flow absorbs large amount of heat flux from turbine to compressor, thus cooling the rotor structure and improving the diabatic cycle efficiency. Finally, the results of this conceptual study show that ultra-micro gas turbine with electric efficiency of up to 5% is feasible, while energy density is increased by factor of 3.6, compared to lithium-ion batteries.
从增材制造300w微型燃气轮机概念设计到无人机应用的新见解
由于碳氢化合物燃料的高能量密度,功率输出低于1千瓦的超微型燃气轮机作为无人机电池替代品具有明显的潜力。然而,以前对这种规模的燃气轮机的研究表明,由于空气轴承故障、从涡轮到压缩机的热量传递、转子动态不稳定和制造限制,存在严峻的挑战。为了克服这些障碍,提出了一种基于传统滚子轴承技术的新型燃气轮机结构,其转速高达500,000 RPM,并采用增材制造的悬臂式单片转子,配备内部冷却叶片。采用绝热循环计算,结合涡轮机械平均线设计规范,阐述了涡轮机械的优化设计。这种方法为传热、组件效率和系统电效率的相互依赖性提供了新的见解。因此,降低设计压力比为2.5,涡轮进口温度为1200k时,最适合300w电力输出。接下来,对现有的增材制造技术进行了回顾,得出了单片转子的材料特性、表面粗糙度和设计约束。然后使用简化的转子模型对四种可用材料进行了转子动力学仿真,以确定有效的永磁体尺寸,以避免接近弯曲模式的运行。为了完善基准发动机结构,提出了一种基于多孔惰性介质燃烧的径向流入燃烧室概念。通过CFD模拟量化压气机效率,并对整体式转子进行了共轭传热分析,以评估不同转子材料的内冷却腔和叶片的效益。结果表明,空腔流吸收了从涡轮到压气机的大量热流,从而冷却了转子结构,提高了非绝热循环效率。最后,本概念研究结果表明,电效率高达5%的超微型燃气轮机是可行的,能量密度比锂离子电池提高3.6倍。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 求助全文
来源期刊
自引率
0.00%
发文量
0
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
确定
请完成安全验证×
copy
已复制链接
快去分享给好友吧!
我知道了
右上角分享
点击右上角分享
0
联系我们:info@booksci.cn Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。 Copyright © 2023 布克学术 All rights reserved.
京ICP备2023020795号-1
ghs 京公网安备 11010802042870号
Book学术文献互助
Book学术文献互助群
群 号:604180095
Book学术官方微信
小红书